User Manual Bluetooth Wireless Earbuds TW10 •18-month limited warranty • Lifetime technical support • support@linpaworld.com • Facebook: @LinpaOfficial www.linpaofficial.
Connection Pair with Your Device: Taking the earbuds from the charging case,the left LED lights alternately flash blue and red,the right LED lights off (Make sure tear off ransparent static sticker on the bottom of the earbuds) Enter pairing mode“TW10” The left LED lights off Connected Tips: ® Bluetooth Devices T10 Pro > on - After booting, no connection automatically shuts down within 60s - Connected for 20 minutes without any playback auto shutdown - Actively turn off the Bluetooth function of t
Pairing issues Pairing issues: The left and right side can be used separately.If there is only one side work.How did I pairing the earbud from single mode to stereo mode? Step 1->: Put them back to the case. Step 2->: Delete “T10 Pro” from Bluetooth menu on your device, if your device menu has been connected “T10 Pro”. Step 3->: Taking the earbuds from the charging case, both earbuds are turned on, the LED lights alternately flash blue and red,Double click on the“R”side.
Controls Music Short press Play/pause songs Double click(Right) Double click(Left) Next track Previous track Click left earbud twice to keep Click right earbud twice to keep Decrease the volume Increase the volume Calling Press Answer/End Call Long press 2 seconds Reject the call Long press 1 second Reject third party calls Double click Connect a new call while retaining the current call Three-party call Double-click to switch between the second party and the third party, and there is a 'didi
Siri/Other voice control software Connect to the standby state, double-click when no music is playing Turn On/Off Taking the earbuds from the charging case Blue light flashes for 3 seconds Long press 5 seconds Red light flashes for 3 seconds
Charging Charge 1.5 h For the charging case 1 When the charging case cannot fully charge the earbuds, if putting the earbuds into the charging case, the red light of the charging case flashes every 3 seconds, this will cycle 10 times. 2 When the charging case is in low battery, if putting the earbuds into the charging case, the red light of the charging case flashes every 1 second. It means you need to charge the case first..
Charging issue 1. Please check if you have tear off transparent static sticker on the bottom of the earbuds. 2. Please adjust the earbuds or take off the ear tips to make sure it connected well with the Conductive needle, or you can exchange the left and right earbuds to check if the charging dock is working. 3. Please take out the earbud from charging dock, and charging the case individually about 30mins, then put back the earbuds to charging dock for charging.
FAQ Sound and Volume: Q: I paired the headphones with my phone but there is no sound from the headphones. A: Make sure the headphones are not muted. Some phones ask for setup of the wireless headphones as an audio output device before sound is transmitted. Please refer to the instructions of your phone for details. Q: The sound quality of the headphones is not good: A: For all of the headphone products, they need a period of use to get better sound quality.
Attention - Never disassemble or modify your earphone for any reasons to avoid any damages and danger. - Do not store the earphone in extreme temperature(under 0℃ or over 45℃). - Do not use this earphone during a thunderstorm to avoid irregular function and increased risk of electricshock. - Do not use harsh chemicals or strong detergents to clean the earbuds. - Keep the earbuds dry Maintenance: 1.
Specifications Model: TW10 FCC ID: 2AKZ8-TW10 Standby time: One year Charging Time: 1.5hours Bluetooth Standard: V5.0 Frequency range: 2.402GHz-2.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.