Instructions Notice

ManualsBrandsDongguan farui Electronics ManualsCamera & PhotoWiFi printing camera

Table Of Contents

页 1

Content

1、Instruction Before Use ..................1

2、Function Keys..............................2/3

3、WiFi Operating Guidance..............4

4、Replace the Printing Paper........... 5

5、TF Card Installation......................6

6、Charging Instruction.....................7

7、Battery &Safety............................7

8、Settery Details............................ .8

1 .Language Setting...............................8

2 .Printing Density................................. 9

3 .Cyclic Record.................................... 9

4 .Sound............................................. 10

5 .Video Quality................................... 10

6 .Record Audio....................................11

7 .Image Quality................................... 11

8 .Continuous Shooting........................12

9 .Camera Timer...................................12

10 .Format......................................... ..13

11 .Recovery Setting........................... . 13

12 .Auto Power-off.............................. . 14

9、Specification............................. .15

10、Q&A.........................................1 6/17

1 .Language Settings

1、Instruction Before Use

1 . Please tear off the protective film of the lens before.

2 . The print needs taking a while to warm up, so the

first pictures are blurry.

8、Setting Details

Press the set button to enter the menu page;

Step 2.Press the up/down button to select the

corresponding requirement.

Step 1.

2 .Printing Density

Note: Larger numbers are higher printing density.

Why it’s blurry？？？

19、Q & A

matter

Printing

problem

Paper does

not come out

Blurred

printing

Printing

paper jam

Print with

missing edges

Streaks in print

Cannot print

out the screen

1. The printing paper should be reserved about 1cm outside the cover

2. Check if the paper cover is tightly closed

3. Check whether the camera's print switch is turned on, or the print

switch is abnormal

1. The thermal paper needs to be preheated, and 2-5 sheets are required

2. The camera has a layer of protective film, which should be removed

before use, which will affect the sharpness of the shooting

3. Adjust the printing density to be high, medium, and low (setting

interface→find printing density→select high, medium and low→OK)

4. The printing paper is not from the original factory (need to be replaced

with original printing paper)

1. The printing paper is not put properly, the printing paper needs to

be rolled tightly

2. Repeated paper jams, restart the camera or reset the keyhole

1. Check whether the paper is in the correct position

1. Reload the paper and pack two more sheets to see if there are still streaks

1. Check whether the printing paper is put in the correct direction

Memory

card

problem

The camera

shows a memory

card error

1. For mat the memory card

2. The camera freezes or restarts repeatedly, and the memory

card n eeds to be replaced

3. The memory card is not compatible with the camera

(the o riginal memory card is required)

The memory

card tray cannot

be ejected

1. Che ck whether there are foreign objects in the memo ry card

sock et and whether the SD is normal

Charging

problem

Screen

problem

Sound

problem

尺寸：90*68mm

18、Specification

Dimensions 90*112*42mm

Display 2.4-inch color screen

Battery specification 7.4V/800mAh lithium battery

Pho to pape r specification 57X27mm glossy

Shooting mode: Single shot, 3-20 seconds timer

Photo resolution 4032*3024, 1920*1440, 1280*960

Video resolution 1080FHD, 720P

Maximum support 32G

Print density 1highest, 2high, 3medium, 4low, 5lowest

Function WIFI Photographing Video Printing

System language Chinese, Japanese , English, Russian, etc.

Continuous shooting 3-10 shots

Loop photography 1-10 minutes

Transmission interface Type-C

Support system WINDOWS XP/7/8

Body weight 178g

Working temperature -5℃ to 40℃

Step 1: Hold the two buckles and outwards to

open the cover of compartment;

WiFi Print

Camera Instructions

Notice: Tear the photo paper in the zigzag direction.

4、Replace the Printing Paper

5、TF Card Installation

1 . Hold the TF card slot in the correct direction until the TF

card is fixed in the card slot. When removing the TF card,

please gently press down the TF card. After the TF card is

ejected, you can take it out. (The TF card must be a

high-speed card above C10 to be used.Please do not plug

or unplug the TF card while the machine is working to

avoid damage to the machine and memory card)

2 . Please pay attention to the direction in which the TF

card is inserted. If it is inserted upside down, it may

damage the machine, TF card and card slot.

3 . When you insert the TF card into the machine, the

machine will set the TF card as the default storage device.

The data in the original TF card may not be readable.

Please make a data backup first.

4 . If the TF card is not compatible with the machine,

please use the format option in the memory menu of the

machine to format the TF card or try another TF card.

6、Charging Instruction

1 . The indicator light is always on during charging, and

the full indicator light is off.

2 . When there is input over-voltage, output

under-voltage and over-voltage, output short circuit or

chip over-temperature, and the battery is not connected,

the indicator light flashes at a frequency of 1.3HZ.

3 . It takes 70-130 minutes to fully charge the battery.

7、Battery & Safety

1 .This machine uses a built-in 7.4V/800mAh polymer

lithium battery, which cannot be removed or replaced.

If it is damaged, contact the seller for repair.

2 .The battery must be charged under adult supervision.

When the battery is charging, the toy switch should be

turned off.

3.The power terminals must not be short-circuited. Do

not connect more than the recommended quantity or the

recommended adapter specification to the power supply

with a voltage greater than the recommended voltage

: 5V___2A).

4 .During the use of the toy, check whether the wire plug

shell and other parts are damaged regularly. If the

damage is found, stop using it until the repair is

complete.

5 .When the machine is not used for a long time, please

charge the battery fully before turning off the power

switch.

Step 2: Select the corresponding APP to download:

FR_PRINT: (IOS Android)

Step 3: Click the menu button and turn on the WiFi;

Step 4: Enter wlan list of your mobile phone and

select the Wifi name of: FR_PRINT;

Step 5: Enter the password: 12345678 to connect

Step 2: Load the printing paper as shown.

Insert the memory card chip face up directly

The display repeatedly

shows the charging screen

The charging icon is

displayed when the machine

is turned on, and it cannot

be used

Unable to turn on, charging

red light is on, unable to display

Unable to turn on,

charging red flashing

Can't turn on, can't charge

Charging light is on,

no display, no power on

Charging is displayed, but it

can’t be displayed when booting

1. Due t o insufficient voltage, it needs to

be rep laced (5V 1A charging head)

1. Afte r reinserting the USB, unplug it again to

chec k whether it is normal/click the system

rese t button

1. Cli ck the system reset button (the small

hole o n the memory card)

1. Che ck whether the USB port is abnormal

1. Cli ck the system reset button (the small

hole o n the memory card)

1. Cli ck the system reset button (the small

hole o n the memory card)

Screen discoloration,

abnormal printing noise

1. Press once, scroll up and down, whether the

color changes again, and determine whether

the filter causes

2. In the settings, the camera is restored to

factory settings

Camera display,

font is not displayed

1. In the settings, the camera restores the

fact ory settings

Camera sound is small

1. Check whether the horn is blocked by

foreign objects

Please read this instruction manual carefully before using the

produc, It contains im portant information,please keep it in a safe place for uset

2、 Function Keys

1 . Up Key

2 . Confirm / Delete Key

3 . Down Key

4 . Back Key / Main Menu

5 . Photo Sticker: Press this button enter the

Sticker Mode and press up/down key to choose

different sticker

6 . Power on/off: Long press for 3 seconds to turn

on/off

7 . Front Camera

8 . Display

9 . Photo / Video / Camera Switch / Video Play

Key: Press this button for photo & video; Long

press it to switch the front / rear camera;

Choose a video from album page and press this

button to play the video

10 . Charging Port

11 . Memory Card Jack

12 . Rear Camera

13 . Print Paper Compartment

3、WiFi Operating Guidance

Step 1: Scan the QR code

to download APP;

3 .Cyclic Record

4 .Sound

5 .Video Quality

6 .Record Audio

7 .Image Quality

8 .Continuous Shooting

9 .Camera Timer

10 . Format

11.Recovery Setting

12 . Auto Power-off

1 2 3 4 5 6 7

15141312

11109

Summary of content (2 pages)

PAGE 1
Content 2、 Function Keys 7 1、Instruction Before Use 1 . Please tear off the protective film of the lens before. 1、Instruction Before Use ..................1 2、Function Keys..............................2/3 3、WiFi Operating Guidance..............4 4、Replace the Printing Paper........... 5 5、TF Card Installation......................6 6、Charging Instruction.....................7 7、Battery &Safety............................7 8、Settery Details.............................
PAGE 2
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.