FS- TH9X INSTRUCTION MANUAL Technical updates available at: Http: / / www. flyskychina.
FS-TH9X Table of contents ......35 9.14 AilDiff 1.Introduction .... . . 2 ......35 9.15 AIR BRAKES 2.Service .... . . 2 9.16 ELE.Flap ......36 3.Meaning of special markings .... . . 3 ......36 9.17 V_Tail 4.Transmitter controls .... . . 5 ......37 5.Radio installation 9.18 ELEVON .... . . 7 5 . 1 R e c e i v e r a n d s e r v o c o n n e c t i o n.... s 9.19 Snap-roll ......37 ..7 5 . 2 C h a r g i n g t h e N i - C d b a t t e r i e s .... . . 8 9.20 THR.needle Mixing ......38 5 .
FS-TH9X 1. Introduction Thank you for purchasing the digital proportional remot control system.If this your first computer radio.rest assured that it is designed to make initial setup and fieldtuning of your more accurate than would be if using a non-computer radio.Although this is a geginner or sport system with the requirements of those flyers in mind,in order to make the best use of your FLYSKY FS-TH9X and to operate it safely,you must carefully read all of the instructions.
FS-TH9X 3.Meaning of special markings Pay special attention to safety where indicated by the following marks: DANGER- Procedures which ma y lead to dangerous conditions and cause death/serious injury if not carried out properly. WARN ING - Procedures which ma y lead to a dangerous condition or cause death or serious injury to the user if not carried out properly,or procedures where the probability of superficial injury or physical dama ge is high.
FS-TH9X 6.Test all controls If aservo operates abnormally,don't attempt to fly until you determine the cause of fhe problem(For PCM systems only:Test to ensure that the FailSafe settings are correct by waiting at least2 mi-nutes after adjusting then,turning the transmitter off and confirming the proper surface/throttle movements,Turn the transmitter back on.) 7 . Start your engine 8.Complete a full range check (see p.9) 9.
FS-TH9X Transmitter controls ANTENNA H OV P IT T H RO C UT LCD DISPLAY HOV THR TRN R UDD D/R GEAR ELE AILE D /R P I T T RIM PROGRAMMABLE STICK PROGRAMMABLE TRIM UP D/R F.MOD AIL/THR STICK PROGRAMMABLE TRIM POWER SWITCH MENU EXIT DOWN LCD MENU: The function of the main menu for button EXIT: Withdraw from the button UP: The menu is chosen upwards DOWN: The menu is chosen downwards +: Increase the value of the parameter -: Reduce the value of the parameter NOTE: Press for short and long 1.
FS-TH9X Carrying Handle CAUTION The module is unre m o vable which is fixed to the product. RF module Trainer function /DSC function connector Battery cover NOTE:If you need to remove or replace the transmitter battery, do not pull on its wires to remove it.Instead,gently pull on the connector's plastic housing where it plugs into the transmitter.
FS-TH9X 5.Radio installation Foll o w t h e s e g u i d e l i n e s t o p r o p e r l y m o u n t the servos,receiver and battery Make certain the alignment tab on the battery,switch and servo connectors is oriented correctly and “ key” into the corresponding notch in the receiver or connectors before plugging them in .when unplugging connectors,never pull on the wires.
FS-TH9X 5. 2 Charging the Ni-Cd batteries Charger TX :Tr an sm it te r ch ar gi ng in di ca to r RX:Receiver charging indicator The transmitter and receiver batteries included with you FS-TH9 X system are rechargeable,Ni-Cd batteries.Ni-Cd batteries require special care and charging. NOTE:The batteries are partially charged,but will require a full, overnight charge before the model may be flown. 1.
FS-TH9X Test two-engine/mot o r o n : .Repeat the test w i t h t h e m o d e l ' s e n g i n e r u n ni n g a n d w i t h s o m e o n e h o l d i n g t h e m o d e l . I f a decrease of more t h a n 1 0 % i s n o t e d , r e s e a r c h a n d r e s o l v e t h e c a u s e o f i n t e r f e r e n c e p r i o r t o flying your model .
FS-TH9X 6.Multi LCD and Programming controls 6. 1 DISPLAY Modulation indicator (PPM&PCM) Throttle/Elevator trim display Model number and name Battery voltage Rudder trim display Timers Aileron trim display Elevator/ Throttle trim display Model type Battery voltage:Battery voltage display (If after the voltage of the battery is lower than 8.5V,Buzzer sends the suggestion sound through 5S once). Modulation indicator:pulse position modulation &pulse code modulation select.
FS-TH9X 7 SYSTEM SETTING STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key for short and choose SYSTEM SETTING menu,press MENU key for short into next submenu. Press the UP or DOWM key to select the SYSTEM SETTING screen. Press MENU key for short into next submenu. Press EXIT Key return last menu. SYSTEM SETTING: M O DEL SELE:This function selects which of the 8 model memories in the transmitter to set up o r fly.
FS-TH9X 7. 2NAME EDIT SYSTEM SETTING STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the SYSTEM SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key to select the NAMEEDIT menu,and press MENU key for short into next submenu. Press the UP or DOWM key to move the cursor to the desired character's position. Press the "+"or"-"key to select the desired character.Press the MENU key for long time enter.
FS-TH9X SYSTEM SETTING 7. 3. 0 HILI TYPE SELECT STEPS: Under the state o f the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the SYSTEM SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN ke y to select the TYPE menu,and p ress MENU key for short into ne xt submenu. Press UP/DOWN key for short and select HELI menu,and press MENU key for short into next menu.
FS-TH9X 7.4 Modulation selection STEPS: SYSTEM SETTING Under the state of the initial picture,press MENU key for long, access the main menu. Press UP/DOWN key select the SYSTEM SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key to select the MODEULAT menu,and press MENU key for short into next submenu. Modulation select: s e ts the type of modeulation transmittec. Press the UP or DOWM key to select the MODULAT screen.
FS-TH9X 7 . 6COPY SYSTEM SETTING STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the SYSTEM SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key to select the COPY menu,and press MENU key for short into next submenu.
FS-TH9X 8 FUNCTION SETTING(HELICOPTER) Page1 Page2 HELICOPTER 8. 1REVERSE STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key to select the REVERSE menu,and press MENU key for short into next submenu. REVERSE: The reverse switch function allows electronic means of reversing the servo's throw .Servo reversing is available for all 9 channels.
FS-TH9X 8. 2THRO CURVE HELICOPTER STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key to select the THRO CURVE menu,and press MENU key for short into next submenu. Press UP/DOWN key to choose the THRO CURVE screen. THRO CURVE: The FS-TH9X offers three separate throttle curves with five adjustable points per curve.
FS-TH9X 8. 4SUB TRIM: HELICOPTER STEPS: Under the state o f the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key choose SUB TRIM menu, press MENU key for short and enter the page to establish. Press UP/DOWN key to choose the SUB TRIM screen. Press "+"or"-" key to adjust the sub-trim position for that selected channel.
FS-TH9X HELICOPTER 8. 6THRO HOLD STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key choose THRO HOLD menu, press MENU key for short and enter the page to establish. Press UP/DOWN key to choose the THEO HOLDM screen. Press "+"or"-" key to select the state(INT or ACT) and change the throttle hold value..
FS-TH9X HELICOPTER 8. 8SWASH MIX STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key choose SWASH MIX menu, press MENU key for short and enter the page to establish. Press UP/DOWN key to choose the SWASH MIX screen.
FS-TH9X HELICOPTER 8. 10TRIM STEPS: Under the state of the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key choose TRIM menu, press MENU key for short and enter the page to establish. Press UP/DOWN key to choose the TRIM screen. TRIM: The FS-TH9X super has digital trims whic are different from conventional mechanical trim slders.
FS-TH9X 8. 12FAIL SAF HELICOPTER STEPS: Under the state o f the initial picture,press MENU key forlong, access the main menu. Press UP/DOWN key select the FUNC SETTING menus,and press MENU key for short into next submenu. Press UP/DOWN key choose FAIL SAF menu, press MENU key for short and enter the page to establish. FAIL SAF: S e ts responses in case of loss of signal or l o w rx battery(PCM mode only). Press UP/DOWN key to choose the FAIL SAF screen.