Install Instructions

FCC Statement:
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
between 20cm the radiator your body.
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
FCC Statement:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
Any changes or modications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
FCC ID: 2APCQ-TAC-138
FCC WARNING:This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Install instructions:
6. Place your device into the bracket, clamping arms
of bracket will closed automatically when it inducts
receiver coil of your device.
5. Extend the foot support according to your phone
size, to align the charging center of your smartphone.
Install instructions:
3. Insert the hook into the car air outlet vane and
tighten to lock. When you hear 'clatter' sounds,
it means the mount has been xed tightly.
4. Connect the charging cable to the charging
interface, after power is on, the clamp arms
will open automatically, the clamp arm can
also be opened by pressing the button on
both sides
.
Install instructions:
1. Insert the adjuster into the ball joint adapter.
2. Insert the ball into the socket at the back of
bracket, turn the adjuster to tighten.
Attentions:
1. Please use the product correctly according instructions.
4. Please do not put wireless charger close to cards with
magnetic stripes or chips (ID card,credit card etc.) to
avoid demagnetization
5. Please keep wireless charger at least 20 CM distance
away from implantable medical device (heart pacemaker,
Implantable cochlea etc.) to avoid potential interferences.
6. Please do safekeeping, do not let your kids treat wireless
charger as toy to avoid unwanted accidents.
The pictures only supplies the reference, please take the
actual product as the standard.
2. Please do not disassemble the product or throw it to re
and water, to avoid leakage that caused by electrical
short circuit.
3. Please do not use wireless charger in high temperature,
wet, corrosive environment, to avoid leakage that caused
by damaged circuit.
Product specication:
Wireless Charging Holder
5W / 7.5W / 10W / 15W (Max)
5V/9V/12V /
Over voltage protection
Input voltage
Output power
115-148KHZ
10W/83% 15W/82.6%
2A / Over current protection
Input current
Frequency
Eciency
4mm (Max)
Induction Distance:
Coil Induction or press button
Open / Close
holder arms:
Support QI / Apple Iphone
7.5W / HUAWEI / SAMSUNG
10W / LG / SONY / GOOGLE /
XIAOMI wireless charging
Compatible with
Fast Wireless
Charging Mode：
2APCQ-TAC-138FCC ID
LED Mode:
Working state LED light color
Power transfer
Standby mode Light o
Charging Red light keeps on
FOD Warning Red light keeps ashing
Charge complete Red light keeps on
Red, blue, red blue light
ash once, then o
Parameters:
Parameters:
Wireless Charging Holder
Air Vent Mount
58-104mm
Charging Indicator :
Turn red when
charging
Type C charging
interface
iPhone13 Pro Max / 12 Pro Max
iPhone 13 / 13 Pro / 12 / 12 Pro
iPhone13 mini / 12 mini
To charge eectively, the foot support
should be adjusted to align the phone
receiving coil to the charging center.
Alignment mark:
Features:
Car holder with wireless charging function, charges
your phone conveniently when driving.
Power output 5W/7.5W/10W/15W, compatible
with all phones with QI standard.
Full 360 degrees rotation for perfect viewing angle.
Start charging once as the phone contact with the
holder, no need plug cable in the phone.
Adjustable foot support makes easy to align to the
charging center.
(Require receiver compliant with WPC Qi standard to match).
Compatible devices:
Qi disabled devices with wireless receiver or wireless
charging case.
Work well with all Qi enabled devices including:
iPhone 13, iPhone13 Pro Max, iPhone13 Pro,
iPhone13 mini, iPhone 12, iPhone12 Pro Max,
iPhone12 Pro, iPhone12 mini, Samsung Note 8,
Note 9, iPhone XS MAS, Huawei P30 Pro, MIUI9,
Samsung S10+, iPhone 8PLus, Samsung S9+,
Samsung S8+, iPhone XR, Samsung S10,
Samsung S7edge, Samsung S8, iPhone XS, iPhone X,
Samsung S9, iPhone 8, iPhone 11, iPhone SE,
Samsung S22, Samsung S21, Samsung S20
Magnetic Fast Wireless
Charging Holder
What is included:
X 1
Please read the instructions carefully before using.
Pictures are for reference only, Specifications are
subject to the physical product
Instructions
Automatic Induction
Fast Wireless Car Charger
X 1
Air vent mount
X 1
6.7 INCH
6.1 INCH
5.4 INCH
15mm
Easy touch
button to
open the
clamps
26 mm
6.7 INCH
6.1 INCH
5.4 INCH
Press both
side buttons
The Type-c cable of
the product has 2
magnetic rings