Install Instructions

FCC Statement:
The equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. During the
operation of device a distance of 15 cm surrounding the
device and 20 cm above the top surface of the device must
be respected.
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help.
FCC Statement:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
Any changes or modications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
FCC ID: 2APCQ-TAC-134
FCC WARNING:This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Install instructions:
6. Place your device into the bracket and press the
clamp arm to lock it tightly.
5. Press the release button to release the clamp arms,
adjust the foot support to t your phone size.
Press button
Install instructions:
3. Insert the mount directly into the car air vent
blade, set the locking switch to proper position.
4. Connect the charging cable to the charging
interface.
Install instructions:
1. Insert the adjuster into the ball joint adapter.
2. Insert the ball into the socket at the back of
bracket, turn the adjuster to tighten.
Attentions:
1. Please use the product correctly according instructions.
4. Please do not put wireless charger close to cards with
magnetic stripes or chips (ID card,credit card etc.) to
avoid demagnetization
5. Please keep wireless charger at least 20 CM distance
away from implantable medical device (heart pacemaker,
Implantable cochlea etc.) to avoid potential interferences.
6. Please do safekeeping, do not let your kids treat wireless
charger as toy to avoid unwanted accidents.
The pictures only supplies the reference, please take the
actual product as the standard.
2. Please do not disassemble the product or throw it to re
and water, to avoid leakage that caused by electrical
short circuit.
3. Please do not use wireless charger in high temperature,
wet, corrosive environment, to avoid leakage that caused
by damaged circuit.
Product specication:
LED Mode:
Wireless Charging Holder
5W/7.5W/10W/15W(Max)
5V/9V/12V
Input voltage
Output power
110-205KHZ
2APCQ-TAC-134
2AInput current
Frequency
FCC ID
Working state LED light color
Power transfer
Red,blue,red blue light turn
on by turns for once,then o
Standby mode Light o
Charging Red light keeps on
FOD Warning Red light keeps ashing
Charge complete Red light keeps on
Parameters:
Air Vent Mount
There are three levels of locking for dierent size AC
vent blades.
2.5-3.5mm
1.8-2.5mm
Within 1.8mm
Loose First position
Second position Third position
Parameters:
Wireless Charging Holder
Easy touch button to
open the clamps
62-106mm
21mm
Charging Indicator :
Turn red when
charging
Type C charging interface
iP 12mini
iP 12(pro)
iP 12 Pro Max
To charge eectively, the foot support
should be adjusted to align the phone
receiving coil to the charging center.
Alignment sticker:
Features:
Compatible devices:
Car holder with wireless charging fuction, charges
your phone conveniently when driving.
Power output 5W/7.5W/10W/15W, compatible with all
phones with QI standard.
Full 360 degrees rotation for perfect viewing angle.
Custom made magnet array, precisely compatible for
iPhone 12 series.
Start charging once as the phone contact with the
holder, no need cable anymore.
Adjustable foot support makes easy to align to the
charging center.
Qi disabled devices with wireless receiver or wireless
charging case.
(Require receiver compliant with WPC Qi standard to match).
Work well with:
iPhone 12, iPhone12 Pro Max, iPhone12 Pro, iPhone12 mini
Samsung Note 8, Note 9, iPhone XS MAS, Huawei P30 Pro, MIUI9,
Samsung S10+, iPhone 8PLus, Samsung S9+, Samsung S8+, iPhone XR,
Samsung S10, Samsung S7edge, Samsung S8, iPhone XS, iPhone X,
Samsung S9, iPhone 8, iPhone 11, iPhone SE, Samsung S21, Samsung S20
Also work with all other Qi enabled devices.
Compatible with MagSafe slim phone cover thickness
within 4mm
Magnetic Fast Wireless
Charging Holder
What is included:
X 1
Air vent mount
X 1
X 1
cableUSB
Please read the instructions carefully before using.
Pictures are for reference only, Specifications are
subject to the physical product
Magnetic Fast Wireless
Charging Holder
Instructions