User's Manual

Infrared Sensor
Wireless Charge Holder
USER MANUAL
Features:
Attentions: Attentions: Attentions:
Compatible devices:
What is included:
Parameters:
Car holder with wireless charging fuction,
charges your phone conveniently when
driving.
Power output 5W/7.5W/10W, compatible with
all phones with QI standard.
Advanced infrared sensor system, automatically
open and clamp your phone onto the mount.
Full 360 degrees rotation for perfect viewing
angle.
Start charging once as the phone contact with
the holder, no need cable anymore.
Fix foot support to t any size of phone, much
convenient for use.
QC 3.0 USB car charger included so you can
start charging readily, with over temperature,
over current, over voltage muti-safety protection.
Infrared Sensor
Wireless Charger Holder
X 1
Air vent mount
X 1
X 1
cableUSB
QC3.0 car charger
X 1
Work well with: iP XS Max / NOTE 8 / 9 / iP XR /
8P / iP XS / iP X / S8 / S9 / iP 8.
Also work with all other Qi enabled devices.
Qi disabled devices with wireless receiver or
wireless charging case.
（Require receiver compliant with WPC Qi
standard to match).
Clamp arms
stretchable
range 59-91mm
Micro USB port
Infrared
Sensor
Transmitter coil
Infrared Sensor Wireless Charger Holder
Parameters:
Product specication:
LED Mode:
Air vent mount
Touch switch
There are three levels of locking for dierent
size AC vent blades.
2.5-3.5mm
1.8-2.5mm
Within 1.8mm
Wireless holder
5W / 7.5W / 10W
DC 5V/9V
Input voltage
Output power
115-205KHZ
2AInput current
Frequency
QC 3.0 car charger
5V 3A, 9V 2A, 12V 1.5A
DC 12-24V
Input voltage
Output Current
Working state LED light color
Power transfer
Red,blue,red blue light turn
on by turns for once,then o
Standby mode Light o
Charging Red light keeps on
FOD Warning Red light keeps ashing
Charge complete Red light keeps on
Attentions:
Please use the product correctly according
to instructions
Please do not disassemble the product or
throw it to re and water, to avoid leakage
caused by electrical short circuit
Please do not use wireless charger in high
temperature, wet, corrosive environment, to
avoid leakage from caused by damaged circuit
Please do not put wireless charger close to
cards with magnetic stripes or chips (ID card,
credit card etc.) to avoid demagnetization
Please keep wireless charger at least 20 CM
distance away from implantable medical device
(heart pacemaker, Implantable cochlea etc.)
to avoid potential interferences
Please do safekeeping, do not let your kids
treat wireless charger as toy to avoid unwanted
accidents
The pictures only supplies the reference, please
take the actual product as the standard
2. Insert the ball into the
socket at the back of
bracket and tighten.
1. Insert the adjuster into
the ball joint adapter.
3. Insert the mount directly
into the car air vent blade,
set the locking switch to
proper position.
6. The holder clamps will
open automatically when
the phone is near 2-3
inches from the infrared
sensor
5. Connect the other end
to car charger, then
insert the car charger to
car cigar lighter.
4. Connect the cable micro
head to your charge
holder.
7. After the phone has been
placed in the holder, the
clamps close automatically
and start charging.
8. The clips will open
automatically when you
touch the touch sensitive
swtich in side edge, take
your phone away
9. The clamps close
automatically
FCC Warning:
This device complies with part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
Loose First position
Second position Third position
Please read the instructions carefully before using.
Pictures are for reference only, Specifications are
subject to the physical product
Support foot