User's Manual

Infrared Sensor
Wireless Charge Holder
USER MANUAL
Infrared Sensor
Wireless Charge Holder
USER MANUAL
What is included:
Infrared sensor wireless
charger holder
X 1
Infrared sensor wireless
charger holder
X 1
Air vent mount
X 1
Please read the instructions carefully before using.
Parameters: Features: Product specification: Attentions: Installation: Installation: Installation: FCC Warning:
What is included: What is included:
Please read the instructions carefully before using.
QC3.0 car charger
X 1
X 1
cableUSB
Air vent mount
X 1
QC3.0 car charger
X 1
X 1
cableUSB
Compatible devices:
LED Mode：
X 1
X 1
Infrared Sensor Wireless Charger Holder
Clamp arms stretchable
range 58-88mm
Harging Indicator :
Turn red when charging
Touch sensitive switch
Infrared Sensor
Suit different thickness of car air vent blades
Transmitter coil
Air vent mount
Infrared Sensor Wireless Charger Holder
Clamp arms stretchable
range 58-88mm
Harging Indicator :
Turn red when charging
Touch sensitive switch
Infrared Sensor
Transmitter coil
Air vent mount
2.5-3.5mm
1.8-2.5mm
1.8mm
Car holder with wireless charging fuction, charges
your phone conveniently when driving
Compliant with 5Ｗ/7.5Ｗ/10W charging power,
QI standrad
Advanced infrared sensor system. Hold your phone
automatically
Clamp arms opens after touching touch sensitive
switc in side edge
Full 360 degrees rotation for perfect viewing angle
Start charging asap as the phone contact with the
holder, no need cable anymore
QC 3.0 USB car charger included so you can start
charging readily, with over temperature, over current,
over voltage muti-safety protection
Work well with: iP XS Max / NOTE 8 / 9 / iP XR /
8P / iP XS / iP X / S8 / S9 / iP 8
Also work with all other Qi enabled devices
Power-on: Red, blue, red blue light turn on
by turns for once, then off
Standby Mode: Light off
Charging: Red light keeps on, remove the
receiver light off and boot into standby mode
Take your device away when charging, light off
and boot into standby mode
When APPLE phone get fully charged, red light
keeps on
When SAMSUNG phone get fully charged, blue
light keeps on
FOD warning:Red light keeps flashing
Qi disabled devices with wireless receiver or
wireless charging case
5. The clips will open
automatically when the
phone is near 2-3 inches
from the infrared sensor
6. Then close in 1 second
automatically and hold
your phone tightly and
start to charge
7. The clips will open
automatically when you
touch the touch sensitive
swtich in side edge, take
your phone away
This device complies with part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC RF exposure statement:
The equipment complies with FCC Radiation exposure limit set
forth for uncontrolled environment.
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
FCC Warning:
This device complies with part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure
condition without restriction.
FCC RF exposure statement:
The equipment complies with FCC Radiation exposure limit set
forth for uncontrolled environment.
This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
8. Then close in 1 second
automatically
使用方法：
（Require receiver compliant with WPC Qi
standard to match)
Wireless holder
QC 3.0 car charger
2A
110-205KHZ
5W/7.5/10W
DC 5V/9V
DC 12-24V
Input voltage
Output Current/voltage 2
Input voltage Input current
Output power Frequency
Output Current/voltage 1
Please use the product correctly according
instructi ons
Please do not disassemble the product or
throw it to fire and water, to avoid leakage
caused by electrical short circuit
Please do not use wireless charger in high
temperature, wet, corrosive environment, to
avoid leakage from caused by damaged circuit
Please do not put wireless charger close to
cards with magnetic stripes or chips (ID card,
credit card etc.) to avoid demagnetization
Please keep wireless charger at least 20 CM
distance away from implantable medical device
(heart pacemaker, Implantable cochlea etc.)
to avoid potential interferences
Please do safekeeping, do not let your kids
treat wireless charger as toy to avoid unwanted
accidents
The pictures only supplies the reference, please
take the actual product as the standard
Attentions:
Compatible devices:
LED Mode：
Car holder with wireless charging fuction, charges
your phone conveniently when driving
Compliant with 5Ｗ/7.5Ｗ/10W charging power,
QI standrad
Advanced infrared sensor system. Hold your phone
automatically
Clamp arms opens after touching touch sensitive
switc in side edge
Full 360 degrees rotation for perfect viewing angle
Start charging asap as the phone contact with the
holder, no need cable anymore
QC 3.0 USB car charger included so you can start
charging readily, with over temperature, over current,
over voltage muti-safety protection
Work well with: iP XS Max / NOTE 8 / 9 / iP XR /
8P / iP XS / iP X / S8 / S9 / iP 8
Also work with all other Qi enabled devices
Power-on: Red, blue, red blue light turn on
by turns for once, then off
Standby Mode: Light off
Charging: Red light keeps on, remove the
receiver light off and boot into standby mode
Take your device away when charging, light off
and boot into standby mode
When APPLE phone get fully charged, red light
keeps on
When SAMSUNG phone get fully charged, blue
light keeps on
FOD warning:Red light keeps flashing
Qi disabled devices with wireless receiver or
wireless charging case
（Require receiver compliant with WPC Qi
standard to match)
Wireless holder
QC 3.0 car charger
2A
110-205KHZ
5W/7.5/10W
DC 5V/9V
DC 12-24V
Input voltage
Output Current/voltage 2
Input voltage Input current
Output power Frequency
Output Current/voltage 1
Please use the product correctly according
instructi ons
Please do not disassemble the product or
throw it to fire and water, to avoid leakage
caused by electrical short circuit
Please do not use wireless charger in high
temperature, wet, corrosive environment, to
avoid leakage from caused by damaged circuit
Please do not put wireless charger close to
cards with magnetic stripes or chips (ID card,
credit card etc.) to avoid demagnetization
Please keep wireless charger at least 20 CM
distance away from implantable medical device
(heart pacemaker, Implantable cochlea etc.)
to avoid potential interferences
Please do safekeeping, do not let your kids
treat wireless charger as toy to avoid unwanted
accidents
The pictures only supplies the reference, please
take the actual product as the standard
1. Insert the ball into the
socket at the back of
bracket and tighten
4. Connect the other end
to green (fast charge)
port of car charger,
insert the charger to car
cigar lighter
2. Insert the mount directly
into the car air vent
blade
3. Intervene USB cable
with your car charger
Note: connect to power
QI charger can speed
up charging speed
Installation: Installation: Installation:
5. The clips will open
automatically when the
phone is near 2-3 inches
from the infrared sensor
6. Then close in 1 second
automatically and hold
your phone tightly and
start to charge
7. The clips will open
automatically when you
touch the touch sensitive
swtich in side edge, take
your phone away
8. Then close in 1 second
automatically
1. Insert the ball into the
socket at the back of
bracket and tighten
4. Connect the other end
to green (fast charge)
port of car charger,
insert the charger to car
cigar lighter
2. Insert the mount directly
into the car air vent
blade
3. Intervene USB cable
with your car charger
Note: connect to power
QI charger can speed
up charging speed
Direction applies to 2.5-3.5 mm air vent.
Direction applies to 1.5-2.5 mm air vent:
Parameters: Features: Product specification: