Installation Instructions

Introduction
Wiring
C olor
F unction
Notes
R ed
Power +
B lack
G N D
G round
G reen
D 0
Wi egand D0
W hi te
D1
B rown
L E D
G reen L E D l ight control
Y ell ow
B uzzer
B uzzer control
Wi egand D1
Installation
1
2
P ar ameter s
A:
B :
A1: 1/8 “
: 1/8
“
1/4 “
1/4 “
5/16 “
1-5/8”
C 1:
C :
W all
A
B
3-1/4 “
3/8 “
3/8 “
C
S te p1
S te p2
S te p3
M odel
Operating Voltage
F requency
C ard Type
R eading Di stance
Output Format
Working Temperature
Standby C urrent
I ndex of P rotection
Di mension
9 18V D C～
H I D card
1
1/8
to 3
1/8
“
HID
- 40˚F - 140˚F
≤25 mA
I P 66
3
P ack i ng L ist
1
R eader
1
M anual
Screw Dri ver
2
Wall F ixing Plugs
2
Self T apping Screws
Name
Q uantity
1
U ser M anual
Proximity Reader
L4
3/4
x W 1
7/8
x H 7/8 “
L4
3/4
x W 3 x H 7/8 “
The Dolphin-NFC-BLE is a Wiegand Output
Proximity Reader. 125KHz HID formats are
compatible with these readers. These readers
have the ability to read a HID format of 26
bits.
These indoor and outdoor readers are
waterproof and functions at extreme
temperatures (-40F - 140F). The readers also
have a built-in light sensor to signal when
the keypad is being tampered.
• Drill 2 holes (A,C) on the wall for the screws
and one hole for the cable
• Knock the wall xing plugs to holes A and C
• Screw the back cover to the wall
• Thread the cable through hole B
• Attach the unit to the back cover
125 kHz EM
125 kHz HID
13.56 MHz NFC Type 2 Tag
13.56 MHZ Mifare, Type 2, and Type 4
2.4 GHz Bluetooth Low Energy
8-24 VDC
Dolphin-NFC-BLE
Dolphin-NFC-BLE
BLE Read Range
~30 feet (10 meters)
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modications not
expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment. (Example - use only shielded interface cables
when connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.