Installation Instructions

STEP 5
Begin activation
Press the silicone button
located on the sensor to begin
activation. The LED light will
blink three times.
STEP 6
Assign sensor to asset
On the asset page, select
your new asset created in step
3. Select “Commission new
sensor.”
Find your new sensor from the
list and follow the prompts.
Required information:
• Asset name
• Nominal speed
• Part number
• Asset type
STEP 7
Installation complete
After completing the installation
process, the application
should function properly.
If there are any problems,
please contact support at
sensortechsupport@
dodgeindustrial.com.
OPTIFY
™
Performance Sensor
Model: DPFSV1
Installation Instructions
Review these instructions in
their entirety before attempting
to install your OPTIFY
Performance Sensor.
Getting Started
Necessary equipment:
Items included in the OPTIFY
Performance Sensor kit:
• OPTIFY Performance
Sensor
• Installation tool
• Rubber cover (optional)
Additional items (required):
• Smartphone
• Computer
Additional items (optional):
• Sensor adapter
• Gloves
• Clean soft cloth
• Torque wrench
• 1-1/4" (32mm) wrench
• 7/16" (11mm) socket
• Socket wrench
STEP 1
Install OPTIFY application
STEP 2
Create an OPTIFY account
using the desktop or mobile
application, then create or join
a plant.
dodgeoptify.com
STEP 3
Create an asset
Log in to the OPTIFY application
with the account created in step 2.
Select “Assets,” then add a new
asset with the “add” button.
Fill in the asset details and select
“Create Asset.”
STEP 4
Mount sensor
Step 4.1
Clean surface to be free of dirt
and debris.
Step 4.2
Find a grease tting, oil plug,
or any other threaded hole that
will accept either the sensor or
sensor adapter.
Optional: Bearing
Locate a grease tting on the
30° face of the bearing and
remove plug.
Optional: Gearing
If being mounted to a gear
reducer, locate the OPTIFY
Performance Sensor adapter
and remove the red push-in plug.
Step 4.3
Thread sensor by hand and
tighten using the installation
tool. If desired, tighten sensor
using a torque wrench, applying
7-12 lbs-in (0.8-1.4Nm).
NOTE: This sensor is intended for application in hazardous location, typical marking shown below.
Specic conditions of use for
this application are as follows:
1. The maximum temperature
of the mounting surface must
be no hotter than +120°C. The
ambient temperature range of
the sensor is -40°C to 105°C.
The installer is responsible
for ensuring that the sensor is
used between these limits. The
assessment of the sensor’s
functionality and its role in
stopping the equipment in the
event of equipment failure is
not implied by the certication,
which is related to its hazardous
area compliance only.
La température maximale de
la surface de montage ne doit
pas être supérieure à +120°C.
La plage de température
ambiante du capteur est de
-40°C à 105°C. L’installateur
est responsable de s’assurer
que le capteur est utilisé entre
ces limites. L’évaluation de
la fonctionnalité du capteur
et de son rôle dans l’arrêt
de l’équipement en cas de
défaillance de l’équipement
n’est pas impliquée par la
certication, qui concerne
uniquement sa conformité aux
zones dangereuses.
2. Under extreme
circumstances, the non-
metallic cap may generate
an ignition-capable level
of electrostatic charge.
Therefore, the sensor
shall not be installed in a
location where the external
conditions are conducive to
the build-up of electrostatic
charge. In addition, the
equipment shall only be
cleaned with a damp cloth,
and the metallic base of the
sensor shall be eectively
connected to earthed metal
when installed.
Dans des circonstances
extrêmes, le capuchon
non métallique peut
générer un niveau de
charge électrostatique
pouvant s’enammer. Par
conséquent, le capteur ne
doit pas être installé dans
un endroit où les conditions
extérieures sont propices à
l’accumulation de charges
électrostatiques. De plus,
l’équipement ne doit
être nettoyé qu’avec un
chion humide et la base
métallique du capteur doit
être eectivement reliée au
métal mis à la terre lorsqu’il
est installé.
To manage your registered
assets, visit OPTIFY:
dodgeoptify.com
MN7002_OPTIFY Performance Sensor_10.22.indd 1MN7002_OPTIFY Performance Sensor_10.22.indd 1 11/2/2022 8:01:21 AM11/2/2022 8:01:21 AM