Supernova™ Flex Installation manual
This page is blank 2
Contents Section Page A Warnings 4 B Required tools 5 C Box contents 5 D Planning 6 E Mounting screen assembly 8 F Setup 15 G Communication 17 H Planning guide 21 I Specifications and dimensions 22 3
A Warnings Caution: a. Do not operate screen before it is installed on wall. b. Follow all installation instructions. Incorrect installation can lead to severe injury and invalidate the dnp warranty. c. Be sure that the wall studs or other mounting fixtures are suitable for mounting the screen and … d. Be sure that the screen is mounted correctly and securely to the wall or the dnp warranty will be invalidated. e.
B Required tools You will need the following tools: Level Phillips screwdriver Power drill Tape measure C Box contents Check box for: Box 1 – Screen 1 1 1 1 3 2 4 2 2 2 1 1 1 Installation manual (this document) User manual Screen assembly Remote control AAA batteries Wall brackets #8 X 2 1/2” Phillips wall mounting screws #8 X 2 1/2” Phillips leveling screws #8-32 Allen head screws for securing screen to wall bracket Washers for leveling screw 3/32” Allen key Power cable IR cable with clip Box 2 - Cover
D Planning D1 Planning screen location a. Locate wall studs or other structural member suitable for bracket mounting. Note: Select studs for mounting that are at least 4” [101 mm] in from end of cover. b. Leave enough clearance at ends to permit access for removing screws from wood shipping fixtures. c. Leave enough top clearance to tighten security screws on top of wall brackets. See planning guide and screen dimensions – sections H & I. d.
D2 Checking screen dimensions a. Determine space requirements for installation. b. Refer to section H Planning guide and section I Specifications and dimensions. c. Ensure proper clearances. _____ D3 Planning projector location a. The projector can be positioned freely on a vertical centerline, perpendicular to the screen, up to 5% above (ceiling mounted) or up to 5% below (table mounted) the image area. b.
E Mounting screen assembly E1 Unpacking bracket hardware a. Unpack two wall brackets. b. Unpack mounting and securing hardware. _____ E2 Lifting screen from box a. Use two people to lift screen from box. b. Lift from box using the two wood packing fixtures at the ends as handles. Warning! Do not lift from middle of screen.
E3 Leveling brackets a. After planning screen location... (using section H Planning guide and section I Specifications and dimensions) b. Mount wall bracket with securing screw at top of bracket. c. Locate wall brackets at least 4” [101 mm] in from end of cover. d. Level wall brackets to each other and tighten leveling screws. ____ E4 Securing wall brackets a. Secure each wall bracket with two (2) wall mounting screws. b. Tighten all screws.
E5 Mounting screen a. Leave wood packing fixtures attached to ends while mounting screen assembly to wall. b. Using two (2) people, grasp wood fixtures, lift, rotate, and seat screen assembly into wall brackets. Warning! Be sure that screen assembly is securely seated before releasing grip. _____ E6 Securing screen assembly a. Ensure that screen is properly seated into both wall brackets. b. Use securing screws to tighten down screen assembly to wall brackets.
E7 Removing wood fixtures a. Remove three (3) end screws from wood packing fixtures and … b. Carefully remove wood packing fixtures from ends of screen assembly. _____ E8 Attaching security clips a. Slide security clips into the cover catches at the ends of the cover. b. Be sure ends of security clips are seated in the cover catches. c. Loosely position security clips near ends of cover.
E9 Seating cover a. Lift cover onto screen assembly. b. Mate the catches on back of cover to lip on top of screen assembly. c. Rotate cover down until it stops. _____ E10 Securing cover a. Position security clips on outside of screen assembly ends and … b. Secure with #8-32 Allen head screws and washers.
E11 Powering up (Plug in) PRESS to BEGIN Insert the plug of the IR receiver cable into the mini-jack socket in the screen (located next to the RS-232 socket). See below. Place the infrared eye in the metal holder and ensure good visible contact to the remote control can be obtained. Plug the power cord into the screen- and wall sockets. a. After plugging in the power cord, • press the House symbol to go to the “Home page” then press [SN Flex] to begin Then PRESS • then press [UP] on the remote b.
E12 Checking smooth operation a. Check extension and retraction of screen. b. Ensure that screen retracts smoothly and does not snag on any parts. c. Ensure that full screen extension operates without hitting obstacles. _____ E13 Aesthetics – hiding cables The cables suspending the screen can easily be coloured to blend with the wall. a. Use a felt-tipped marker matching the colour of the wall. b.
F Setup with remote control The remote control has a programmable display with buttons on the screen (soft buttons) and arrow buttons below the screen for menu navigation. The remote is factory programmed for the Supernova Flex and can be further programmed for use with other electronic components. Please see the remote control manual for programming instructions.
Setting a new bottom position • • • • Press [ ] to go to “Home Page” Then Press [Flex] Press the right arrow button and shift to Page 2. Press & hold [▲] or [▼] until screen is at desired position then press save. Note: the screen will shift up and down slightly (10mm) to signify that it read the command. • Shift back to Page 1 and test setting with [UP] & [DOWN] keys. Changing the Speed Supernova Flex has three possible speed “Low, Medium and High”. The screen will arrive set for the “Medium” speed.
G Communication IR remote control The screen is operated by the standard protocol, RC5. Please see below for details: The illustration shows a typical pulse train of an RC5 message. This example transmits command $35-53 to address $05-5.
User commands This section describes most common user commands in detail. Items enclosed in square brackets are optional. Items enclosed in angle brackets are to be replaced by specific values. For example, the command syntax for lowering the screen is: d[own] Possible command lines are down 100 do 50 d 200 Status messages are sent by the controller in response to a command line.
i[nfo] Shows system information. info 301 System settings follow Firmware=0.3.6 Serial=0000000016 Bottom=2502 SpeedLimit=50 Position=2502 Speed=0 . m[ove] Moves the screen to absolute position . move 2000 101 Moving to 2000 203 Screen stopped at 1994 move 2000 420 Already there s[et] b[ottom] Sets current position as bottom position.
x Immediately stops current screen movement. bottom 101 Moving to 2642 x 203 Screen stopped at 1034 12V-Trigger control To operate the Supernova Flex through contact closures, a pluggable terminal block connection is available. The terminal block has seven positions for wires. For contact closure operation, the five terminals on the left side of the terminal block are used.
H Planning guide Use the below information and the size specifications (section I Specifications and dimensions) to determine the placement of the screen and the wall brackets. See section I Specifications and dimensions for data of your screen.
I Specifications and dimensions Specifications per screen size Screen size 72" 1.33:1 4:3 format 84" 100" 72" 84" 92" 100" Product no. 5072500000 5084500000 5100500000 5072600000 5084600000 5092600000 5100600000 mm 1463 1707 2032 1594 1860 2037 2214 Aspect ratio dnp Supernova Flex™ Width Image area Height Width Cover dimension Height Width Screen dimension incl.
www.dnp.dk www.supernovascreen.
Rev. 2.2 dnp denmark as – Skruegangen 2 – DK – 2690 Karlslunde – Denmark – Tel: +45 46 16 51 00 – Fax: +45 46 16 52 00 – dnp@dnp.