dnp Supernova™ Flex Classic Installation guide dnp optical front projection screens Content: Safety instructions What is in the box Screen installation on wall Screen installation on ceiling Installation of remote controls User guide Service guide > dnp denmark as Skruegangen 2 DK-2690 Karlslunde Denmark > Phone +45 4616 5100 Fax +45 4616 5200 www.dnp-screens.com dnp@dnp.
dnp Supernova™ Flex Classic Installation guide Safety instructions Important Safety Instructions (EN) >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> Read the instructions Keep the instructions Heed all warnings Follow all instructions Clean only with dry cloth Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a third grounding prong.
dnp Supernova™ Flex Classic Installation guide Instructions de sécurité importantes (FR) >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> Lire ces instructions Conserver ces instructions Tenir compte de tous les avertissements Suivre toutes les instructions Nettoyer uniquement avec un chiffon sec. Ne bloquer aucune ouverture de ventilation. Installer conformément aux instructions du fabricant Ne pas négliger la sécurité que procure une prise avec raccordement à la terre.
dnp Supernova™ Flex Classic Installation guide Battery Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Do not use re-chargeable batteries. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Danger d’explosion si la pile n’est pas remplacée correctement. Ne remplacer que par le même type ou un type équivalent.
dnp Supernova™ Flex Classic Installation guide What is in the box? Screen case Plate.B ( Plate.A (x2) Screen Plate (Preins the top of scre Remote Control Bar Screw.D (x4) (4x8 mm) Screw.E (x4) (4x5 mm) Screw.F (x10) Plate.A (x2) (4x30 mm) Plate.B (x2) Screw.G (x2) (Preinstalled in top Plate.B with washers) Safety screw (x4) Plate.C (x4) (Preinstalled on Plate.
Wall dnp Supernova™ Flex Classic Installation guide Screen installation on wall (For installation on ceiling, please go to page 8) Make sure that you are at least two people to do the screen installation. 1. 2. Attach Plate.A to the wall using appropriate fasteners (Screw.F can be used). Measure the length of the screen case and install the plates far enough apart so that the plates will be near the ends of the screen when it is installed. We recommend that the center of Plate.
dnp Supernova™ Flex Classic Installation guide 3. Attach the screen case to the wall by sliding Plate.B (mounted on the screen case) onto Plate.A (mounted on the wall). Install Screw.G and tighten securely. Screw.G Plate.A Screw.G Plate.B Screen case Screw.F ew.F Slide Wall Wall Wall 4. Install two safety wires with the safety screws into Plate.C and into the wall with Screw.F or other appropriate screw. Safety wire Install Screw.E for extra safety. Screw.F Safety screw Safety wire Screw.
dnp Supernova™ Flex Classic Installation guide Screen installation on ceiling Make sure that you are at least two people to do the screen installation. Front 1. Attach Plate.A to the ceiling using appropriate fasteners (Screw.F can be used). Measure the length of the screen case and install the plates far enough apart so that the plates will be near the ends of the screen when it is installed. The plates must be lined up parallel to each other to ensure proper operation of the screen.
dnp Supernova™ Flex Classic Installation guide 3. Attach the screen case to the ceiling by sliding Plate.B (mounted on the screen case) onto Plate.A (mounted on the ceiling). Install Screw.G and tighten securely. Screw.F Ceiling Slide Plate.A te.A Plate.B Screw.G Screw.G Screen case 4. Install two safety wires with the safety screws into Plate.C and into the ceiling with Screw.F or other appropriate screw. Use other safety screw Screw.F to fixate Plate.C. Screw.
dnp Supernova™ Flex Classic Installation guide Installation of remote controls InfraRed sensor Connect the enclosed IR sensor to any of the two RJ45 sockets. The front socket is recommended to get best visible contact to the remote control transmitter. Remember to direct the front of the IR sensor to the front of the screen. The front of the IR sensor has a dnp logo. See later section on how to use the remote control.
dnp Supernova™ Flex Classic Installation guide Electrical connection dnp Supernova Flex Classic Screens are available with two different voltages power supplies depending on the requirement where it will be used. The following chart indicates the wire colours used. Version 110V 230V Ground Neutral Line Green White Black Green/Yellow Blue Brown To prevent the chance of fire or injury, use a qualified technician for all electrical wiring connections.
dnp Supernova™ Flex Classic Installation guide User guide Using the remote control Upper button = Move the screen to top position The screen will raise automatically and stop. Middle button = Stop the screen Use to immediately stop the screen. Lower button = Move the screen to bottom position The screen will lower automatically and stop. Changing the screen stop positions Top and bottom positions are set at the factory. Do NOT change the top position! Risk of damaging screen If not done correctly.
ges dnp Supernova™ Flex Classic Installation guide To set a new TOP position (not recommended): A. Remove the battery cover B. Press the small right button (P2) shortly, until LED lits. If the button is held 2 4 too long (> 3 seconds), and a beep is heard, redo this step. C. Wihtin 3 seconds after step B, press the Upper button (2) and release (This step puts the screen in a mode to set the top position) D.
dnp Supernova™ Flex Classic Installation guide How to pair motor and IR remote control 01 Press the small white motor programming button until the 3rd beep is heard (about 10 seconds) to erase the memory. 02 03 Press the small white motor programming button until the 1st beep is heard to switch to pairing mode. Within 5 seconds after step 2: Press the Middle button (stop button) on the pairing remote control. Motor and remote are now paired.
dnp Supernova™ Flex Classic Installation guide Service guide Maintenance To clean your dnp screen, use a clean damp soft cloth and dry with a clean soft cloth. If your screen is extremely dirty use a mild detergent diluted in water in a clean damp soft cloth. Use a clean damp cloth with water only to remove any detergent residue. Do NOT use any type of abrasive material, oily cleaners or thinners (such as paint thinner, benzene or acetone) on your dnp screen. This will damage the surface of the screen.