OWNER’S GUIDE INSTALLATION GUIDE 7” Widescreen TFT LCD Color Monitor Owner’s/Installation Manual MODEL HVM 702 © 2004 Directed Electronics, Inc.
NON-TRANSFERABLE LIMITED ONE YEAR CONSUMER WARRANTY Directed Electronics, Inc. (Directed) promises to the original purchaser that the new automotive video monitor and/or source unit(s) (the Product), excluding accessories, that is purchased and installed from a Directed authorized dealer more than ninety (90) days after the purchase of a new vehicle is warranted for a period of one (1) year from date of purchase of the Product.
Table of Contents Non-Transferable Limited One Year Consumer Warranty . . . . . . . . . . . . . . . . . .2 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 What is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Notes 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 4 Before operating your LCD Monitor system, please read these instructions carefully. Retain this manual for future reference. Do not remove any WARNING stickers on the unit. Do not use any chemical solvent, cleaning agent or corrosive detergent to clean away dirt on the surface of the screen. Doing so may cause irreversible damage to the surface of the LCD screen.
Introduction Congratulations on your purchase of the world’s finest video entertainment system. At Directed we are committed to bringing you the most technologically advanced products available. We are pleased that you chose a Directed Video product. Through years of critical testing and hand craftsmanship, we have created a wide range of video entertainment products for your viewing pleasure.
What is Included 7” TFT LCD Color Monitor Mounting hardware package Headrest housing EV sponge Headrest bezel DIN to RCA cable (for A/V input) Remote Control Unit/battery System Description MONITOR REMOTE CONTROL 19 8 18 17 9 10 16 11 12 1 2 3 4 5 6 15 14 13 7 MONITOR 1. 2. 3. 4. 5. 6. 7.
10. Volume control—if the OSD is active, these allow scrolling through menu options 11. Menu On/Off—press the menu button to go back to the previous selection 12. Scan—used in conjunction with a TV tuner 13. A/M—used in conjunction with a TV tuner 14. TX—not used 15. DIM—dims the LCD screen 16. Up/down button for menu 17. MODE—changes the viewing aspect ratio (Full, 4:3, or Wide) 18. SOURCE—used in conjunction with a TV tuner 19.
Battery Replacement 1. Follow the instructions given in the illustration below to open the battery holder. 2. Remove the old battery and replace it with a CR2025 or equivalent. The positive (+) side of the battery must be facing upward in the clip. 3. Push the battery holder into the body of the remote control until the battery holder is locked. 4. Properly dispose of the old battery. 2 1 Operation POWER ON/OFF 1.
Press the SEL button on the remote control to the mute the audio, press again to restore audio. NOTE: If the MENU button on the remote has been pressed prior to pressing the SEL button, the SEL button now selects a menu item to be adjusted. MENU (ADJUSTMENTS) 1. Press the MENU button on the remote to display the following four groups: VIDEO Bright Color Tint Dimmer Reset AUDIO Volume Bass Mute H/P MODE Full 4:3 Wide DISP PAL/NT UP/DN LET/RIT 2.
AUDIO VOLUME: 0–15 BASS: ON OFF MUTE: ON OFF H/P: A-CH B-CH — This setting allows the use of 2 headphones on different frequencies. If two video units are installed and; for example, each unit is playing a different video, using two headphones set at the same frequency may result in interference of the audio signal between the two headphones. One of the video units should be set to A-CH and the other to B-CH. A-CH is 2.3MHz left and 2.8MHz right, B-CH is 3.2MHz left and 3.8MHz right.
Headrest Housing/Bezel Installation 1. Remove the cover from the headrest. 2. Using the headrest housing as a template, position the housing over the backside of the headrest and mark the foam with a felt tip pen. Cut the marked portion of foam and pull out the cut portion. 3. Insert the headrest housing into the headrest and secure the the headrest. Usually wire ties attached to the headrest posts is sufficient. NOTE: Ensure that the UP arrow on the headrest housing is pointing up. 4.
Headrest Installation 1. Unplug the DIN cable from the monitor. 8-pin main DIN cable 5-pin adapter cable 2. Connect the LCD screen’s 8-pin DIN plug into the 8-pin DIN plug of the headrest. NOTE: When assembling the cable, match the arrows at each end of the connector. NOTE: Feed and orient the connector assembly behind the shroud mount in the lower right hand corner. You may have to feed some of the DIN cable up into the headrest to accomplish this positioning. 3.
5. To remove the monitor from the mounting shroud for service or repair, insert and slide a plastic card at the edge of the monitor. This will remove the clip engagement of the monitor. Slightly lift this side of the monitor out, then repeat this procedure on the other side of the monitor. Typical Wiring Diagram © 2004 Directed Electronics, Inc.
Multiple A/V Input Selector Refer to diagram on the next page for the discussion that follows: CONNECTING A MONITOR TO MULTIPLE SOURCES When the monitor(s) power is turned on the input source will appear in the upper right hand corner (AV1, AV2, etc.). Press the SOURCE button on the remote to switch between the available sources for that monitor. NOTE: If PARKING is displayed on the screen, it means that this monitor(s) will not display video until the parking brake is set (vehicle parked).
VS102 © 2004 Directed Electronics, Inc.
Troubleshooting Use the following chart to assist in troubleshooting the system. PROBLEM SOLUTION Power will not turn on Check connections to the power supply and other devices. No picture or sound Check connections of external device. Have picture, but no sound Remote control does not work Intermittent audio Check if the volume is set to low. If in A/V mode, check audio connections. Avoid using the product under strong & direct sunlight. Replace the battery in the remote control.
Specifications Power 12VDC (9–16VDC) Power consumption 750mA Maximum @ 12VDC Power consumption (stand-by) 50mA Video type PAL/NTSC Video input level 1Vp-p, 75 ohm (composite) A-ch 2.3 MHz/2.8MHz IR frequency (left/right) B-ch 3.2 MHz/3.8MHz 1m ±30º IR range 1m ±15º Headphone stereo output 0.5 watts - 16 ohms/channel Actual screen size 155 (W) X 880 (H) mm Dimensions 189.4 (W) X 126.
© 2004 Directed Electronics, Inc.
Notes ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ ______________________________ __________
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security, car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.