DPV-5200X_manualcover_ENG 8/17/06 5:00 PM Page 1 Targa DPV-5200x ou: y r o f R e a dy a rg a . d e w w w. t Front panel connections 1. Disc Tray Insert a disc here. User's guide and service information 2. 1/I Switches the unit to ON or OFF. 3. PROG. (V/v) Channel Programme Selectors. 4. DVD Opens or closes the disc tray. 5. Display window Shows the current status of the unit. DVD: DVD deck is selected. : A disc is loaded in the DVD deck. [P]: Indicates the Progressive Scan is set to On mode.
DPV-5200X_manualcover_ENG 8/17/06 5:00 PM Page 4 Remote control - Overview POWER Switch this unit ON or OFF. OPEN/CLOSE EJECT Open or close the disc tray. Tape Eject. TV/VCR Switch between your TV’s tuner and the VCR’s internal tuner. DVD/VCR selection switch Selects operation mode of the remote control. Switches modes of the device. AV Select input source for recording into tape. PAUSE/STEP ( ) Pause playback temporarily / press repeatedly for frame-by-frame playback. SKIP (.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 2 Important Instructions 1 The following instructions should be read before the product is operated. 2 This instruction manual should be retained for future reference. 3 Heed all warnings. 4 All operating and use instructions should be followed. 5 Do not use this product near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 3 Safety Precautions RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 4 Table of Contents Introduction Operation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 About the Symbol Display . . . . . . . . . . . . . . 5 Symbol used in this Manual . . . . . . . . . . . . . . . 5 Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . 5 Handling Discs . . .
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 5 To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference. Notes on Discs This manual provides information on the operation and maintenance of your DVD player. Should the unit require service, contact an authorized service location. Handling Discs Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 6 Before Use (Continued) Types of Playable Discs DVD (8 cm / 12 cm disc) Video CD (VCD) (8 cm / 12 cm disc) Audio CD (8 cm / 12 cm disc) In addition, this unit plays DVD±R/RW, CD-R/RW and SVCD that contains audio titles, DivX, MP3, WMA, and/or JPEG files. This indicates a product feature that is capable of playing DVD-RW discs recorded with Video Recording format.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 7 Front Panel 2 3 4 5 1. Disc Tray Insert a disc here. 2. 1/I Switches the unit to ON or OFF. 3. PROG. (V/v) Channel Programme Selectors. 4. DVD Opens or closes the disc tray. 5. Display window Shows the current status of the unit. DVD: DVD deck is selected. : A disc is loaded in the DVD deck. [P]: Indicates the Progressive Scan is set to On mode. : Indicates repeat mode. : DVD+VCR is in timer recording or a timer recording is programmed.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 8 Remote Control POWER Switch this unit ON or OFF. OPEN/CLOSE EJECT Open or close the disc tray. Tape Eject. TV/VCR Switch between your TV’s tuner and the VCR’s internal tuner. DVD/VCR selection switch Selects operation mode of the remote control. Switches modes of the device. AV Select input source for recording into tape. DISPLAY CLK/CNT Access the On-Screen Display. Shows you the current time or counter.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 9 Rear Panel Introduction AERIAL Connect the aerial using this jack. VIDEO/AUDIO OUT(Left/Right) (DVD/VCR OUT) Connect to a TV with video and audio inputs. COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr) (DVD EXCLUSIVE OUT) Connect to a TV with Y Pb Pr inputs. AUDIO OUT (Left/Right) (DVD EXCLUSIVE OUT) Connect to an amplifier, receiver or stereo system.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:34 AM Page 10 Connections DVD exclusive out connection Caution: Make sure this unit is connected directly to the TV. Set the TV to the correct video input channel. Do not connect this unit’s AUDIO OUT jack to the phone in jack (record deck) of your audio system. Connecting to a TV & Decoder (or Satellite) Make one of the following connections, depending on the capabilities of your existing equipment. Basic connection (AV) 1.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 11 Connections (Continued) Connecting to Optional Equipment Rear of this unit Preparation Connecting to an amplifier equipped with two channel analog stereo or Dolby Pro Logic II/Pro Logic Connect the Left and Right DVD/VCR AUDIO OUT or AUDIO OUT (DVD EXCLUSIVE OUT) jacks on this unit to the audio left and right in jacks on your amplifier, receiver or stereo system, using the audio cables.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 12 Before Operation-VCR part Tuning in a video channel on your TV Using your VCR for the very first time Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the DVD+VCR through the RF cable. Following picture will display on the TV screen when you have just connected your video recorder for the very first time.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 13 Before Operation-VCR part Setting the clock Manually To set the colour system The clock in your DVD+VCR controls time and date settings for your DVD+VCR. The clock is set automatically during ACMS (Automatic Channel Memory System) when your DVD+VCR detects a channel that broadcasts a Teletext signal. If the broadcast signal is weak the clock will not be set and will require setting manually. 1. Press i. 3.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 14 Before Operation-VCR part How to use the main menu Tuning in TV Stations Automatically This DVD+VCR can easily be programmed by using the menus displayed on screen. The menus are controlled by the Remote Control Handset. If the TV broadcast signal is weak your DVD+VCR may not detect the necessary information and will not be able to store them correctly. To overcome this problem please turn to the MANUAL TUNING section on page 15. 1.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 15 Before Operation-VCR part Tuning in TV Stations Manually 1. Press i. The main menu will appear on the TV screen. Press 1 or 2 to select the PR SET. Press ENTER/OK. PSET R Pr-12 ACMS PR 04 CH C04 STATION MFT 00 CHANNEL/CABLE : AV PSET R i 6. Press 2 to select STATION so that you may name your TV station. Press ENTER/OK. 7. Use 3 or 4 to select letters and numbers for the station name. Use 1 or 2 to move back and forth between characters.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 16 Before Operation-VCR part Changing the order of TV Stations Deleting TV Stations After tuning TV stations into your DVD+VCR you may wish to change the order in which they are stored without having to retune them again. The instructions given on this page will show you how you can simply move them into your desired order. After tuning TV stations into your DVD+VCR you may wish to delete a station.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 17 Before Operation-DVD part You can display various information about the disc loaded on-screen. 1. Press DVD to switch the device into DVD mode. 2. Press DISPLAY to show various playback information. The items displayed differ depending on the disc type or playing status. 1/3 1 / 12 Initial Settings By using the DVD Setup menu, you can make various adjustments to items such as picture and sound.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 18 Before Operation-DVD part LANGUAGE Progressive Scan Progressive Scan Video provides the highest quality pictures with less flickering. If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 19 Before Operation-DVD part AUDIO LOCK (Parental Control) Each DVD disc has a variety of audio output options. Set this unit’s AUDIO options according to the type of audio system you use. Rating Unlock Password New Area Code DG IE Preparation LOCK AUDIO Dolby Digital Bitstream DTS Bitstream MPEG PCM Sample Freq. 48KHz DRC On Vocal On DVD Blocks playback of rated DVDs based on their content. Not all discs are rated.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 20 Before Operation - DVD part Area Code DivX(R) VOD DVD Enter the Area Code whose standards were used to rate the DVD video disc, based on the list in the reference chapter (see page 36). 1. Select “Area Code” on the LOCK menu then press B. 2. Follow step 2 as shown left (Rating). 3. Select the first character using v / V buttons. 4. Press B and select the second character using v / V buttons.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 21 Playing a tape You will only be able to load and eject video cassettes when your DVD+VCR is plugged into the mains. Your DVD+VCR may also playback recordings from NTSC tapes (on PAL TV). Getting a better picture When a cassette is inserted and playback started, the automatic tracking function works to get the best possible picture automatically.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 22 Operation with tape Instant Timer Recording (ITR) Your DVD+VCR allows you to make recordings using a variety of simple methods: Instant Timer Recording (ITR) start recording immediately for a set period of time or until the video cassette runs out. Your DVD+VCR incorporates Long Play (LP) which enables you to record up to twice the amount of time on a video cassette.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 23 VIDEO Plus+ Programming VIDEO Plus+ greatly simplifies entering the date, channel, start and end times of a Timer Recording by simply entering PlusCode Programming numbers. PlusCode Programming numbers are published in most TV guide magazines; they can vary one to nine numbers in length. VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 24 Operation with tape Timer recording using On Screen Display You may set up to seven timer record events within one month of the current date.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 25 Timer recording using On Screen Display (Continued) 9. Press i to set another timer record event and follow steps 3 to 8. Check that the timer event details are correct. Press i return to screen. If PLEASE CHECK is displayed, you have entered incorrectly and will need to re-enter the data. 10. Press POWER to switch your DVD+VCR to Timer Standby mode.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 26 Additional Operation - VCR part Hi-Fi Stereo Sound System Tape Counter Memory Stop Your VCR will record and playback Hi-Fi stereo sound. In addition it has a stereo NICAM digital stereo sound decoder. This allows you to record and playback the sound in several different ways. Video cassettes recorded on your VCR will have a normal mono audio track and two VHS Hi-Fi stereo audio tracks.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 27 Video Doctor (Self-Diagnosis) Wide Screen Compatibility 16:9 This feature informs you that there is a problem with your DVD+VCR. These error messages will appear on the TV screen. Your DVD+VCR can record and play back wide screen aspect ratio programmes (16:9). To record a wide screen format programme successfully the correct type of wide screen signal must be broadcast by the TV station. 1. Press i. Press 1 or 2 to select Press ENTER/OK.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 28 Additional Operation - VCR part Recording from External Components Copying from DVD to VCR You can record from an external component, such as a camcorder or VCR, connected to any of the DVD+VCR’s external inputs. You can copy the contents of a DVD to a VHS tape. 1. Make sure that the component you want to record from is connected properly to the DVD+VCR. 2. Insert a blank VHS video tape into the VCR deck. 2.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 29 General Playback features - DVD Part Operations Z (OPEN / CLOSE) Opens or closes the disc tray. X (PAUSE) ./> Discs ALL During playback, press X to pause playback. ALL Press X repeatedly to play Frame-by-Frame. DVD During playback, press . or > to go to the next chapter/track or to return to the beginning of the current chapter/track. ALL VCD DivX VCD DivX Press . twice briefly to step back to the previous chapter/track.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 30 Playing a DVD or Video CD Notes on general features: Marker Search • On a Video CD with PBC, you must set PBC to Off on the setup menu to use the repeat function (See “PBC” on page 20). To enter a Marker • If you press > once during Repeat Chapter (Track) playback, the repeat playback cancels. • Zoom may not work on some DVDs.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 31 Playing an Audio CD or MP3/WMA file MP3/ WMA/ Audio CD Once you insert an MP3/WMA files recorded media or Audio CD, a menu appears on the TV screen. Press v / V to select a track/file then press PLAY or ENTER and playback starts. You can use variable playback functions. Refer to page 29-30.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 32 Viewing a JPEG file This unit can play JPEG files recorded media. Moving to another File 1. Insert a JPEG files recorded media. The PHOTO menu appears on the TV screen. Press . or > or cursor (b or B) once while viewing a picture to advance to the next or previous file. PHOTO Zoom Preview List During watching pictures, press ZOOM to enlarge the video image (4 steps). You can move through the zoomed picture using b B v V buttons.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 33 Playing a DivX Movie file 1. Insert a DivX file recorded media. The MOVIE menu appears on the TV screen. MOVIE 0:00:00 List Movie Folder 1 Movie Folder 2 Movie Folder 3 DivX disc compatibility with this player is limited as follows: • Available resolution size of the DivX file is under 720x576 (W x H) pixel. • The file name of the DivX subtitle is available by 56 characters. Movie Folder 4 Movie Folder 5 Movie Folder 6 Movie Folder 7 Movie Folder 8 2.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 34 Playing a DVD VR format Disc This unit will play DVD-R/RW discs recorded using the DVD-Video format that have been finalized using a DVD-recorder. • This unit will play DVD-RW discs recorded using the Video Recording (VR) format. 1. Insert a disc and close the tray, It start playing automatically. 2. The DVD-VR menu appears on the TV screen when you press DISC MENU buttons while playing. DVD-VR 3.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 35 Additional Operation Maintenance and Service Operation Refer to the information in this chapter before contacting a service technician. Handling the Unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 36 Language and Area Code List Language Code List Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 37 Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Correction Cause No power. The power cord is disconnected. Plug the power cord into the wall outlet securely. The power is on, but the DVD player does not work. No disc is inserted. Insert a disc. No picture. The TV is not set to receive this unit’s signal output.
V1503P1Z.NA6ITTA/S_38U 8/18/06 9:35 AM Page 38 Specification General Power requirements Power consumption Dimensions (approx.) Mass (approx.) Operating temperature Operating humidity Timer RF Modulator AC 220-240V, 50 Hz 17W 430 x 78.5 x 265 mm (W x H x D) 4.