User's Manual

ManualsBrandsDigitalWay ManualsElectronicsMASS STORAGE

Table of Contents

1. Safety Precautions

2. Composition

3. Introduction & Specifications

4. Overview

5. HS200 Using

STEP 1 Driver Installation

STEP 2 Data Storage

STEP 3 Removing HS200 From Your Computer

6. Formatting

7. Troubleshooting

1. Safety Precautions

* You should be fully aware of the notice below, before using the product.

* The company does not take the responsibility for the defect of the product (accessory, connecting device

etc.), damage, data loss, accident & disorder etc., occurred from not fully understanding the notice below,

so please be sure to check this notice.

. Do not use the product for the other purpose except for the matters described in the manual.

. Pay attention not to hurt your hand while you touch a product box, manual, accessory etc.

. Hard disk is sensitive to impact. Pay attention not to have a severe impact on the product, might cause a

trouble or a damage.

. Pay attention not to use the device or leave it alone in places with high temperature and humidity or of

high thermal difference, and by the strong magnetic body.

. Remember that liquid (water, beverage etc.) not leaked into the device.

. The device that you discretionary disassembled or remodeled can not be provided with a free service and

can be excluded from the service areas, so pay special attention to this.

. The company shall not be held liable for data lost and damaged during data transmissions between

HS200 and your computer.

. Be sure to backup your data during data storage. Device malfunction, operational errors, external shock,

or power failure can cause loss of stored data. The company does not assume any liability for such

occurrences. Please take proper precaution

. Customers must back up the data stored in the device before requesting for the service. For the service-

requested device, the data are assumed to have been backed up by customers ; we do not provide any data

backup service separately. We assume no liability for any data loss during the service.

. Please plug or unplug the cable by holding the plugs not by pulling out the cable, to prevent internal line

breaking.

Summary of content (5 pages)

PAGE 1
Table of Contents 1. Safety Precautions 2. Composition 3. Introduction & Specifications 4. Overview 5. HS200 Using STEP 1 Driver Installation STEP 2 Data Storage STEP 3 Removing HS200 From Your Computer 6. Formatting 7. Troubleshooting 1. Safety Precautions * You should be fully aware of the notice below, before using the product. * The company does not take the responsibility for the defect of the product (accessory, connecting device etc.), damage, data loss, accident & disorder etc.
PAGE 2
. Do not give an impact to the connected part while the Computer is connected to the device. . When the device is covered with foreign particles, please wipe off it with soft cloth or clean towel and be careful not to use chemicals 2. Composition 1. HS200 2. Manual 3. Installation CD 4. USB Long Cable 5. USB Short Cable (Optional) 6. Case (Optional) 7. Necklace & Mini USB Adapter 3. Introduction & Specifications 1.
PAGE 3
4. HS200 Overview A. USB Terminal When connecting the device to the computer with a USB cable, connect terminal A of this cable to the USB terminal of the computer. Then insert the HS200 Body USB terminal into USB cable B. B. LED Green light – this indicates the connection of the device to the computer when power is turned on. Red light – indicates that the disk is transmitting the data. C. Hole for necklace 5. HS200 Using 1.
PAGE 4
2. If you select “Safely Remove Hardware” the following message pops up. 3. When the window for the “Safely Remove Hardware” appears, select the “USB Mass Storage Device” in the window. This indicates the hardware device. Click the [Stop] button. 4. When the “Stop a Hardware Device” window appears, confirm the “USB Mass Storage Device” item and then press the [OK] button. 5. When the window for the “Safe Detachment of Hardware” appears, press the [Close] button, remove HS200 from the computer. 6.
PAGE 5
Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.