WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. NT9010 v 1.0 Installation Guide DLS-3 v1.
Limited Warranty Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
Tab l e o f C o n t e nt s Chapter 1: Quick Set Up Section 1.1: Introduction 1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 About the NT9010 System ................................. 1 About the NT9010 Manual Set .......................... 1 Main system Specifications ................................. 2 Additional Devices ............................................. 3 Peel-off Instruction Labels .................................. 4 Section 1.2: Installing The NT9010 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 1.2.8 1.2.
WARNING Please Read Carefully N o te t o I ns t a lle rs This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. S y st e m Fa ilu re s This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
Chapter 1: Quick Set Up Section 1.1: Introduction 1.1.1 About the NT9010 System The NT9010 is a full-featured, wireless security system. It has been designed for fast and easy installation. The NT9010 system is made up of the following components: • A main control unit • Up to 32 wireless detectors and panic pendants (total) • You can also add up to 16 wireless keys. The NT9010 system supports up to 32 zones (detectors and panic pendants), and 32 system users.
Chapter 1: Quick Set Up ☛ Programming Worksheets This manual is used to record your zone choices and other programming for the system. NOTE: Keep this manual in a safe place for future reference. ☛ User’s Guide The User’s Guide provides easy to follow instructions for NT9010 users. This Guide contains instructions on turning the system on or off, dealing with alarms and emergencies, using advanced functions, fire safety, and how to replace wireless device batteries.
S ec ti o n 1 .
Chapter 1: Quick Set Up WLS912-433 Wireless Glassbreak Detector The wireless glassbreak detector can be used to provide wireless glassbreak detection. The unit comes with three AA batteries. WLS914-433 Dual PIR Wireless Motion Detector The dual PIR wireless motion detector can be used to provide wireless space protection. The unit comes with four AA batteries.
Section 1.2: Installing The NT9010 Please read this section to get an overall understanding of the steps involved in installing the NT9010 system. Carefully work through each step. This will help to reduce problems and to reduce the overall installation time required. 1.2.
Chapter 1: Quick Set Up NOTE: Complete all wiring before applying AC power. Figure 1: Removing NT9010 Wall-Mount Backplate 2. Twist with Screwdriver 1. Remove plastic screw 2. Twist with Screwdriver 3. Pull top of backplate away from NT9010 To remove the backplate from the NT9010: 1. Remove the plastic screw from the top of the NT9010 unit (see Figure 1). Keep the screw in a safe location so that you can replace it later. 2. Insert a flathead screwdriver in the slots shown in Figure 1.
Se c t i o n 1 . 2 : I n s ta l l i n g Th e NT 9 01 0 Connecting AC and Telephone Wiring Connect the AC and telephone line wiring to the terminals mounted on the NT9010 backplate. When you later attach the NT9010 to the backplate, the posts on the back of the unit will plug into the terminals, completing the connection. Figure 2: AC and Telephone Line Wiring AC Terminals For the NT9010 to work correctly, you will need to connect it to an AC power source that is not controlled by a switch.
Chapter 1: Quick Set Up Use the following NT9010 terminals to make your zone connections: There are two different ways in which zones may be wired, depending on which programming options have been selected. The system can be programmed to supervise normally closed, or Single End of Line loops. Please refer to the following sections to study each type of individually supervised zone wiring. Normally Closed (NC) Loops To enable normally closed loops, programming section [013], option [1] must be ON.
Se c t i o n 1 . 2 : I n s ta l l i n g Th e NT 9 01 0 Keyswitch Zone Wiring Zones may be programmed to be used as keyswitch arming zones and must be wired according to the following diagram: For a complete description of how keyswitch zones operate, see 2.3.1 Zone Definitions on page 36. Connecting the Remote Sounder You can connect a hardwired remote sounder to the NT9010 system.
Chapter 1: Quick Set Up 1.2.6 Mounting the Wireless Devices Do not permanently mount the wireless devices until you have completed the Placement Tests (see 1.2.7 Enrolling Devices and Setting Up the System on page 10). Once you have a good location for each of the devices, follow the mounting instructions on the Installation Instruction sheet for each device. For WLS904P-433, see Appendix D: WLS904P Wireless Motion Detector Installation Instructions on page 62.
Se c t i o n 1 . 2 : I n s ta l l i n g Th e NT 9 01 0 NOTE: To ensure that the NT9010 works properly, you should enroll all entry/exit point zones first. NOTE: PIR’s covering entry points should be zone type [06] Delay Stay/Away [01] Delay 1 Zone: If this zone is violated when the system is armed (e.g. door or window is opened), the entry delay will begin. The buzzer will sound to warn the user that the system must be disarmed.
Chapter 1: Quick Set Up Programming Zone Labels If an enrolled device is a door/window contact, motion detector, glassbreak detector, or smoke detector the system will then prompt you to enter an audio label for the new zone.
Se c t i o n 1 . 2 : I n s ta l l i n g Th e NT 9 01 0 duct a dial tone search before dialing. If necessary, you can enter the following hexadecimal digits in the telephone number: • HEX B to dial “✱” (function button B “Away”) • HEX C to dial “#” (function button C “Chime”) • HEX D for an additional dial tone search (function button D “Exit”) • HEX E to insert a 2-second pause (function button E “Status”) When you have finished entering the telephone number, press [✱].
Section 1.3: Troubleshooting 1.3.1 Typical Installation Problems and Solutions When I try a placement test I get no result or “Bad” results. Check the following: • Are you testing the correct zone? • Was the correct serial number entered when the device was enrolled? • Is the device in range of the NT9010? Try testing the device in the same room as the NT9010. • Are you testing the zone correctly? (See the Installation Instruction sheet for each device for testing instructions.
Chapter 2: Advanced Programming Section 2.1: Programming the NT9010 The chapter describes how to use advanced programming. For instructions on using Flash Programming, please see Chapter 1: Quick Set Up Guide. 2.1.1 How to Enter You can use the Advanced Programming to set all communicator and system options. The Installer Code is [5555] at default, but should be changed to prevent Advanced Programming unauthorized access to programming. Step 1: From any keypad enter [✱][8][Installer Code].
Chapter 2: Advanced Programming You can use also the Forward (Playback) button to go forwards through the programming data. The Backward (Record) button will not work in the advanced programming sections (except for sections [301] to [303], and section [402]). 2.1.3 Programming You may need to enter hexadecimal (HEX) digits for some of the programming secHexadecimal tions.
S ec ti o n 2 . 1 : P r o g r a m m i n g th e NT 9 01 0 4. If you want to use a recorded label, in place of the first word of the label enter [244], then the number of the label [001] to [005]. The recorded label will replace all six words in the section. To record a label, see Recording Custom Labels on page 17. 5. When you have entered the label, the system will recite it. If the label is correct, press [#]. To change the label, repeat steps 1-4, above. 6.
Chapter 2: Advanced Programming NOTE: If the NT9010 is completely powered down (both AC and battery power are lost), the recorded labels will be lost. 2.1.6 Reviewing To review the current programming for a section enter the 3-digit section number. Programming The NT9010 will announce the data programmed. If the programming is correct press [#] to exit the section, otherwise enter the correct data. 2.1.7 18 Exiting When the NT9010 announces “Enter Section Number”, press the [#] key.
Section 2.2: Changing How the NT9010 Works For Users Most NT9010 installations will only require basic programming. You can complete the basic programming using the NT9010 Flash Programming (please see Chapter 1: Quick Set Up for more information). The NT9010 User’s Guide provides basic directions for arming and disarming the system, bypassing zones and performing user functions.
Chapter 2: Advanced Programming 1. Call the telephone number the NT9010 system is connected to. 2. Let the telephone ring one or two times. 3. Hang up and wait 10 seconds before calling again. The NT9010 will answer after the first or second ring and announce “Hello.” 4. Enter the 3-digit Telephone Access Code. If this is not entered within 10 seconds the NT9010 will hang up. Once the correct code has been entered, the system will prompt, “Enter your Access Code.” 5. Enter a 4- or 6-digit access code.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s Duress Codes - Access Codes [33] and [34] When a Duress Code is used to perform any function the system will send a Duress Reporting Code to the central station (see 2.3.12 CommunicatorReporting Codes on page 47). Master Code - Access Code [40] The Master Codes can perform any keypad function. These codes can be used to program all access codes, including the Duress Codes.
Chapter 2: Advanced Programming To program each attribute: 1. Enter [✱][5][Master code][9] to enter the attribute programming mode. 2. Enter the 2-digit number of the access code you want to edit. 3. Enter the attribute number to toggle it on or off. The programmable attributes are as follows: • Attribute 1: User enabled for arming, disarming, alarm reset, auto-arm cancel (on by default) • Attribute 2: For future use • Attribute 3: Zone Bypass enabled This attribute allows the user to bypass zones.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s tem [✱] command prompts: if a prompt is disabled, users will still be able to enter the command it refers to. Sub-section [003] determines which Status prompts the user will hear. If an option is “ON”, the system will announce the prompt when the appropriate condition is present. If an option is “OFF”, the system will not announce the prompt if the condition is present.
Chapter 2: Advanced Programming NOTE: The alarm announcements will stop with the siren at the end of the Bell Time Out period. Verbal Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [017], Option [3] Alarm Tone Period for Verbal Alarm . . . . . . . . . . . . . . . . . . . . . .Section [807]-[030] 2.2.5 Arming and Disarming Options If the Arm/Disarm Bell Squawk option is enabled the system will squawk the alarm output once upon arming and twice upon disarming.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s Opening After Alarm Bell Ringback . . . . . . . . . . . . . . . . . Section [381], Option [2] Closing Confirmation. . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [381], Option [4] AC/DC Inhibit Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [701], Option [3] 2.2.6 Automatic Arming You can program the system to automatically arm at a specific time every day.
Chapter 2: Advanced Programming NOTE: If the system has been Stay armed, or armed with no entry delay ([✱][9]), pressing the Away key will not start an exit delay. For some applications Bell Squawk on Exit Delay may be enabled. The system will squawk the alarm output once every second when the exit delay is initiated and 3 times a second for the last 10 seconds until the exit delay expires. Upon entry, if a Delay type zone is violated, the system will begin entry delay. The keypad will emit a steady tone.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s NOTE: Only fire zones will follow the Temporal Three Fire Signal. Bell Cut-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [005] Temporal Three Fire Signal Enable/Disable . . . . . . . . . . . . Section [013], Option [8] Fire Bell Continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [014], Option [8] 2.2.
Chapter 2: Advanced Programming The NT9010 will only announce “Service Required”. If the control unit announces this trouble, users can press [1] to expand the troubles. The user should call for assistance. The specific trouble will be logged in the event buffer. AC Failure: AC power is no longer being supplied to the NT9010 control unit. To conserve power, when there is an AC Failure all lights will turn off, except for the flashing System light.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s [*] [4] Door Chime On/Off Users can turn the Door Chime feature on or off by pressing [✱][4]. If the door chime feature is enabled the keypad will beep 6 times rapidly when a zone is opened and closed. The system will only do this for zones with the Door Chime Attribute enabled and if the door chime feature is enabled (see 2.3.2 Zone Attributes on page 38).
Chapter 2: Advanced Programming hours. During this time the system will answer incoming downloading calls (see 2.3.14 Downloading on page 51). • [6] – User-Initiated Call-Up When [6] is pressed, the system will initiate a call to the downloading computer. • [7] Telephone Volume Control You can change the volume of the voice prompts heard when you access the NT9010 system by telephone. When you press [7], the NT9010 will prompt “Phone Volume is High. To change phone volume, press ‘1’. To exit press #.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s 2.2.10 Function Keys There are eight function keys on the NT9010 labelled Stay, Away, Chime, Exit, Status, Volume, Record and Playback. The operation of these keys is described below. Users can activate each function by pressing the key. The programming of any function key on the NT9010 may be changed to any of the options listed below. To change the programming of a function key: 1. 2. 3. 4.
Chapter 2: Advanced Programming [09] - [✱]+[2] Trouble Display This function key provides the user with a simple method for entering the Trouble Display Mode (see [*] [2] Trouble Announcements on page 27). [10] - [✱]+[3] Alarm Memory This function key provides the user with a simple method for entering the Alarm Memory Display Mode (see [*] [3] Alarm Memory on page 28). [11] - [✱]+[5] Programming Access Codes This function key provides the user with a simple method for programming access codes.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s NOTE: Keys [27] to [30] are instant function keys. They do not have to be held for 2 seconds to activate. 2.2.11 Programming If you will be adding WLS929-433 wireless keys, after you enroll them on the system you may want to change the functions of the buttons on these devices.
Chapter 2: Advanced Programming If the Fire Keys option is enabled, when the Fire keys are pressed and held for 2 seconds, the system will activate the alarm output. It pulses one second on, one second off only if option 8 of Section [013] is disabled (Standard Fire option). If Fire Bell Continuous is selected the alarm output will sound until a code is entered; otherwise it will sound until a code is entered or the alarm output times out. Communication of the signal to central station is immediate.
S e c t i o n 2. 2: C h an g i n g H o w t h e N T 90 1 0 W o r k s F o r U s e r s Number of Invalid Codes Before Lockout . . . . . . . . . . . . . . . . . . . . . . Section [012] Lockout Duration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [012] Keypad Blanking Option . . . . . . . . . . . . . . . . . . . . . . . . . Section [016], Option [3] Code Required to Restore Blanking . . . . . . . . . . . . . . . . . Section [016], Option [4] Keypad Backlighting Option.
Section 2.3: Changing Other NT9010 Functions Most installations will only require basic programming. You can complete the basic programming using the NT9010’s Flash Programming (please see Chapter 1: Quick Set Up for more information). This section explains programmable features that affect the internal functioning of the system, including zone operation, central station communications, talk/listen-in features, computer downloading features, and other advanced options. 2.3.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s ing on page 27). Typically this zone is used for interior protection devices, such as motion detectors. [06] Delay Stay/Away Zone: This zone type will operate the same as the Interior Stay/Away zone type except that it will always provide entry delay.
Chapter 2: Advanced Programming [87] tem is stay armed, this zone will be active, but when it is tripped, it will initiate the entry delay. Delayed 24 Hour Fire (Wireless): If this zone is violated (e.g. the smoke detector senses smoke), the alarm will immediately sound, but the alarm communication to the central station will be delayed for 30 seconds. If during the 30 second delay the user presses the [#] key, the alarm and communicator will be delayed an additional 90 seconds.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s • Wireless Zone Determines if the zone is a wireless zone or a hardwired zone. Allows the system to generate low battery trouble and zone supervisories. NOTE: The wireless zone attribute must be enabled for all enrolled wireless zones. Audible/Silent Alarm . . . . . . . . . . . . . . . . . . . . . .Section [101] to [132], Option [1] Pulsed/Steady Alarm . . . . . . . . . . . . . . . . . . . . . .
Chapter 2: Advanced Programming 2.3.5 Wireless Zone Supervision NOTE: The RF Jam Detect zone, hardwired zones, and Panic Pendants must have the supervision option disabled. Wireless Supervisory Window Each wireless zone will send a supervisory signal every 64 minutes. If the receiver does not receive a signal within the time programmed for the Wireless Supervisory Window, it will generate a supervisory fault. To program the wireless supervisory window, from Advanced Programming: 1. 2. 3. 4.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s RF Jamming Detection Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . Section [807]-[093] 2.3.7 Zone Tamper/ By enabling Tampers/Faults Do Not Show as Open, faults and tampers for wireFault Options less zones will not be annunciated, and will be hidden from the end user. If the option is disabled, faults and tampers will be annunciated.
Chapter 2: Advanced Programming c) the system picks up the telephone line again and searches for a dial tone for 5 seconds d) the system will then dial regardless of the presence of dial tone If there is no initial handshake recognized within 40 seconds the system will then hang up the line. If the Force Dialing option is disabled, each attempt will still follow the above pattern, except that the system will not dial in step (d) if no dial tone is detected.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s Communicator Enabled/Disabled . . . . . . . . . . . . . . . . . . . Section [380], Option [1] Pulse Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [3] Switch to Pulse Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [4] Post Dial Wait for Handshake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [161] Maximum Dialing Attempts .
Chapter 2: Advanced Programming 3rd telephone number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [303] 3rd telephone number enable . . . . . . . . . . . . . . . . . . . . . Section [380], Option [5] Alternate Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [380], Option [6] 2.3.10 Communicator The system Account Codes will be used by the NT9010 when communicating system events (e.g. Low Battery, Test Transmission).
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s ■ 4 digit account number [4079] - program [4A79] 5. When programming reporting codes two digits must be entered. If one digit reporting codes are to be used the second digit must be programmed as a ‘0’. If a ‘0’ is to be transmitted substitute the HEX digit ‘A’ for the ‘0’. Examples: ■ 1 digit reporting code [3] - program [30] ■ 2 digit reporting code [30] - program [3A] 6.
Chapter 2: Advanced Programming Additional Notes on Contact ID 1. Account numbers must be four digits. 2. If the digit ‘0’ is in the account number substitute the HEX digit ‘A’ for the ‘0’. 3. All reporting codes must be two digits. 4. If the digit ‘0’ is in the reporting code substitute the HEX digit ‘A’ for the ‘0’. 5. To prevent the system from reporting an event program the reporting code for the event as [00] or [FF]. Communicator Format Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s Pager Format The Communicator Format option for either telephone number can be programmed for Pager Format. If an event occurs and the Communicator Call Direction options direct the call to a telephone number with the Pager Format selected the system will attempt to page. When calling a pager extra digits will be required to make it work properly.
Chapter 2: Advanced Programming timer expires, the system will transmit the programmed reporting code. If the system is disarmed before the timer expires, the alarm will not be transmitted. The Transmission Delay zone attribute determines which zones will start the timer. Transmission Delay Zone Attributes . . . . . . . . . . Sections [101] to [132], Option [7] Transmission Delay Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s Zone Restorals If the Restoral on Bell Time-out option is selected, the system will send the Zone Restoral Reporting Code for the zone if the bell cut-off time has expired and the zone is secured. If the zone is not secured when the bell cut-off time expires, the system will send the restoral immediately once the zone is secured, or when the system is disarmed.
Chapter 2: Advanced Programming NOTE: If Talk/Listen-In is used in a multiple room situation, an NT9201 remote sounder is highly recommended. Event Options Panic key alarms will activate the Listen-In feature, if the Panic Keys Alarm option is enabled. Auxiliary key alarms will activate the feature if the Auxiliary Keys Alarm option is enabled. Listen-in will be initiated if a Duress code is entered at a keypad and the Duress Alarm option is enabled.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s Information regarding the programming of the Command Keys must come from the central station to which you will be reporting. Once you have talked to the central station, program the telephone keys to operate as they require. Talk/Listen-in on Phone Lines 1/3 . . . . . . . . . . . . . . . . . . . .Section [381], option [5] Talk/Listen-in on Phone Line 2 . . . . . . . . . . . . . . . . . . . . . .
Chapter 2: Advanced Programming If the Full 6-hour User Enabled DLS Window option is enabled, when the user opens the DLS window with [✱][6][Master code][5], the DLS window will remain open for six hours. The DLS window will remain open after a successful hang-up from a downloading call.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s 2.3.15 Telephone Line Monitoring (TLM) When the TLM Enable option is selected, the system will supervise the telephone line and will indicate a trouble condition if the telephone line is disconnected. If the TLM Enable option is ON, the system will check the telephone line every 10 seconds.
Chapter 2: Advanced Programming 2.3.17 Event Buffer The system will store the last 128 events that have occurred on the system. Each event will contain the time, date, and the event itself along with the zone number, access code number or any other information pertaining to the event. If the Event Buffer Follows Swinger Shutdown feature is enabled the event buffer will not store events after the swinger shutdown level has been reached.
S ec ti o n 2 . 3 : C h a n g i n g O t h e r NT 9 0 10 F u n c t i o n s The system will take a few seconds to reset. When the keypad is operational, the default is complete. You can also return the main controller, wireless receiver and audio interface programming to factory default settings individually. To return the main control to default settings, use section [992]. To return the wireless receiver to default settings, use section [996].
Chapter 2: Advanced Programming Installer Lockout Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [990] Installer Lockout Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section [991] 2.3.22 Walk Test The Installer Walk Test can be used to test the alarm state of each zone of the system. Before beginning the walk test, ensure the following conditions are met: 1. 2. 3. 4.
Appendix A: Guidelines for Locating Smoke Detectors Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home.
Appendix B: Reporting Codes The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes about individual reporting codes, see 2.3.11 Communicator Reporting Formats on page 44 and 2.3.12 CommunicatorReporting Codes on page 47. Contact ID The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information about the signal.
Section # Reporting Code Code Sent When...
Appendix B: Reporting Codes Table2: Contact ID Zone Alarm/Restoral Event Codes (as per ADEMCO): Program any of these codes for zone alarms/restorals when using the standard (non-automatic) Contact ID reporting format.
Appendix C: WLS925L-433 Mini Door/ W i n do w C o nt a ct I n s t a ll a t io n I n s t r uc t i on s Remove Cover At the notched location on the cover, insert the flat blade of a small screwdriver between the base and the cover and twist the screwdriver to pop the cover off. Install Battery Use care when installing the battery and observe the correct polarity (see diagram below). Use only Eveready Lithium Energizer No. EL123AP battery. NOTE:Battery replacement must only be done by a qualified technician.
Appendix D: WLS904P Wireless Motion Dete ct or Insta llat ion Ins tructions The WLS904P is designed to combine the convenience of a wireless detector with effective and reliable detection of human motion as well as good protection against the nuisance alarms associated with pets weighing up to 60 lbs (27.3 kg) Installing The Detector WLS904P provides effective immunity to single or multiple pets whose total combined weight does not exceed 60 lbs. (27.
High Traffic Shutdown Mode To prolong battery life, the motion detector uses a feature called High Traffic Shutdown. When motion is detected, the device will transmit to the receiver and will then shut down for three minutes. If motion is detected again during the shutdown time, the unit will not transmit the event to the receiver. The detector will thus remain in the shutdown mode until three minutes after the first motion detected was transmitted.
F C C C O M P L IA N CE S TAT EM E N T CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
