Installation Guide

ManualsBrandsDigital Monitoring Products ManualsElectronicsZ-Wave Interface

738Zplus Z-WAVE INTERFACE MODULE

Installation Guide

DESCRIPTION

17103

SELECT THE LOCATION

Select a central location for the 738Zplus Z-Wave Interface

Module. Keep in mind that at least one Z-Wave Plus device

must be within 65 feet of the 738Zplus. Most Z-Wave Plus

devices act as repeaters for the signal to create longer and

multiple transmission routes (battery-powered Z-Wave Plus

devices do not repeat signals in order to extend battery life).

See Figure 2.

Note: Place the module away from large, metal objects

to avoid interference with the Z-Wave Plus signal.

MOUNT THE 738Zplus

1. With the housing cover o, carefully remove the

738Zplus’s PCB from the housing.

2. Use the supplied screws to secure the 738Zplus

housing against a wall or ﬂat surface. See Figure 3.

The 738Zplus Z-Wave Interface

Module allows DMP panels to

communicate with up to 232

Z-Wave or Z-Wave Plus devices,

such as light controls, light bulbs,

door locks, garage door openers,

and thermostats.

The 738Zplus is automatically

recognized by DMP panels, and no

additional programming is required.

Once the 738Zplus is connected to

a DMP panel, users can immediately

begin adding Z-Wave devices to

their system.

The 738Zplus connects to the

panel’s keypad bus and takes

control of the system’s Z-Wave Plus

devices using an integrated wireless

network. Devices can be remote

controlled from smartphones using

the DMP Virtual Keypad™ app,

or from any mobile device using

MyAccess™ text commands.

Compatibility

The 738Zplus module is compatible with:

• DMP XT30/XT50 Series panels,

Version 171 or higher

• All Z-Wave and Z-Wave Plus

devices

What is Included?

One model 738Zplus with housing

and a hardware pack

Figure 2: Example Z-Wave Plus Transmission Routes

= Z-Wave Plus Device

Oce

Dining

Living Room

Foyer

Kitchen

Garage

Control

Panel with

738Zplus

Figure 3: 738Zplus Housing with Mounting Holes

Mounting Holes

Figure 1: 738Zplus Z-Wave

Interface Module

Summary of content (4 pages)

PAGE 1
738Zplus Z-WAVE INTERFACE MODULE Installation Guide 1 Figure 1: 738Zplus Z-Wave Interface Module SELECT THE LOCATION Select a central location for the 738Zplus Z-Wave Interface Module. Keep in mind that at least one Z-Wave Plus device must be within 65 feet of the 738Zplus. Most Z-Wave Plus devices act as repeaters for the signal to create longer and multiple transmission routes (battery-powered Z-Wave Plus devices do not repeat signals in order to extend battery life). See Figure 2.
PAGE 2
3 WIRE THE 738Zplus The 738Zplus has four wire connections to connect to the panel’s keypad bus. See Figure 4. 1. Connecting the wires to the 738Zplus terminals. a. Connect the wire that delivers power to the module to the RED terminal. b. Connect the wire that sends data from the module to the YEL terminal. c. Connect the wire that receives data from the panel to the GRN terminal. d. Connect the ground wire to the BLK terminal. 2.
PAGE 3
FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons.
PAGE 4
Z-Wave Device Compatibility Specifications Power Requirements Operating Voltage Current Draw Frequency Range 8.0 to 14VDC 35mA 908 MHz Dimensions 4.5”W x 2.75”H x 1.75”D Color White Housing Material Flame retardant ABS Certifications Z-Wave Certification: FCC Part 15 ID: Industry Canada: ZC08-14080002 CCKPC0137 5251A-PC0137 Designed, engineered, and manufactured in Springfield, Missouri Z-Wave GE Light Control Modules with and without dimmer (ex.