Installation Guide 9800 Series Wireless Graphic Touchscreen Keypads CURRENT 82 HI LO TODAY 98 77 WEDNESDAY 98 77 HI LO
© 2014 Digital Monitoring Products, Inc. Information furnished by DMP is believed to be accurate and reliable. This information is subject to change without notice.
DMP Keypad Features DMP Wireless Graphic Touchscreen Keypads offer flexible features and functionality in a stylish design. Each keypad provides: • AC Power/Armed LED • Full color touchscreen display • Internal speaker • Wireless communication • 12 Vdc plug-in power supply • Internal rechargeable 3.
Select Areas There are four Select Areas in the display as seen in Figure 2. These Select Areas are one of the features that make the system so easy to operate. They allow you to make selections by pressing the area over each key, icon, or other selection to operate the keypad. Warning: DO NOT use any sharp objects to operate the touchscreen such as a pen or pencil.
Internal Speaker Operation All keypads emit standard tones for screen presses, entry delay, and system alerts. The speaker also provides distinct burglary, fire, zone monitor, and prewarn cadences. The keypads provide an alternate prewarn with alarm cadence that occurs when the status list displays a zone alarm. Micro SD Card The 9800 Series Wireless Graphic Touchscreen Keypads provide a spring-loaded Micro SD card slot on the right edge of the keypad housing.
End-User Options All keypads provide three keypad adjustments the end-user can make through a User Options Menu. The user can also view the keypad model number and address. Scroll through the carousel menu and press the Options icon until it glows. The screen displays the available options shown below. See Figure 7 for example. Backlighting Brightness Set the backlight illumination and AC Power/Armed LED brightness level.
Keypad Serial Number For your convenience, an additional pre-printed serial number label is included. Prior to installing the device, record the serial number or place the pre-printed serial number label on the panel programming sheet. This number is required during programming. The keypads can be programmed into the control panel by entering the serial number in Device Setup panel programming, or alternatively using the wireless keypad association operation.
Mounting the Keypad Secure the keypad base to the wall ensuring that the wall tamper switch makes proper contact with the wall. Use the supplied screws in the mounting hole locations as shown in Figure 9.
Standby Battery The keypad rechargeable battery provides 24 hours of backup battery power when primary DC power is not available. It is shipped already installed inside the keypad. The battery is intended for backup power only and not to operate the keypad on a daily basis. If the battery is low, or not plugged into the internal J3 battery connector, a low battery condition is indicated by the panel when the battery falls below 3.62 volts.
Programming the Keypad in the Panel The keypads can be programmed into the control panel by entering the serial number in Device Setup panel programming, or alternatively using the wireless keypad association operation. A maximum of 4 keypads may be used with the panel. Device Setup Programming Program the keypad as a device in Device Setup during panel programming. At the serial number prompt, enter the eight-digit serial number. Continue to program the device as directed in the panel programming guide.
Installer Options Menu Keypad Options and Keypad Diagnostic menus allow installing and service technicians to configure and test keypad operation. Access the Installer Options Menu Access the Options menu through the carousel menu. While in the Option display, press the Installer Options icon and enter the code 3577 (INST) at the keypad and press CMD.
enable Tamper? NO yes CARD OPTIONS DMP CUSTOM Custom Card Definitions WIEGAND CODE LENGTH 26 Enable Tamper? Select YES to enable wall tamper protection. Default is NO. Card Options Select DMP to indicate the reader sends a 26-bit DMP data string. To save the DMP option, press DMP and then press CMD. Select CUSTOM if using a non-DMP credential. To select CUSTOM press the right side of the display. When CUSTOM displays, press CMD. Default is DMP.
Require site Code: no yes Site codes 1-4 > > > > SITE CODES 5-8 > > > > NO COMM WITH PNL OFF Choose action Off site any on Choose action Last Require Site Code Press YES to use a site code, for non-DMP cards, and press CMD to view the site code entry display. Default is NO. In addition to User Code verification, door access is only granted when any one site code programmed at the SITE CODES entry option matches the site code received in the Wiegand string.
SYSTEM AREA A/P H/A HSA dealer logo add delete adding logo sure? no yes Dealer info Add Delete adding info sure? no yes 12 System Configure the keypad as the same system type selected in System Options panel programming. Select HSA when zones are assigned to Bedrooms for the Sleep area to be active. Dealer Logo Use this option to add a custom dealer logo to the Main Screen of the keypad.
Carousel Z-Wave Items The Z-Wave Carousel Items screen allows you to select CAROUSEL Z-WAVE ITEMS the Z-Wave options to be displayed in the Carousel menu on the main screen. Press the item to select and a check-mark displays. Press again to de-select. Items for the Carousel include Lights, Locks, Thermostats and Favorites. Pressing CMD at the bottom of the CMD screen advances to the next screen and the Back Arrow returns you to the previous option. Default is no Figure 13: Carousel Z-Wave items selected.
Accessing Keypad Diagnostics If necessary, refer to Access the Options Menu earlier in this document. KPD KPD KPD OPT DIAG RF STOP Z1 OPEN Z3 OPEN Z2 OPEN Z4 OPEN Input wiegand Keypad Diagnostics (KPD DIAG) This option displays Zone Test. Zone Test This option allows the keypads to display the current electrical status of the four protection zones. The status is shown as OPEN, SHRT, or OKAY. Note: The Zone Test displays on other keypads without built-in zones, but is not operational.
Appendix Preloading Custom Dealer Logo Information A custom dealer logo and dealer information may be added to the Main Screen of the keypad prior to being connected to the panel. Use the following steps: 1. Connect the 12 Volt DC power supply to the keypad. 2. Power up the keypad and the keypad screen displays SYSTEM BUSY. 3. Press CMD to display ENTER CODE:. 4. Enter 3577 and press CMD to access the Installer Menu. 5. Press KPD OPT to access keypad options menu. 6.
Programming Cards into the System Access the User Menu by pressing the Keypad icon in the carousel menu on the main screen, then press CMD until MENU? NO YES displays. From the User Menu, select USER CODES. Choose ADD. At the ENTER CODE: - display, present the credential to the reader. The keypad works by reading the 4 to 10-digit user code from the data sent by the access control reader.
Keypad Arming and Disarming Area system Arming and Disarming Press the lock icon and select the arming/disarming option. The keypad displays ENTER CODE: -. Present your card to the reader. Once validated by the system, all areas assigned to your code arm or disarm automatically and the 9863 keypad Door Strike relay activates.
Keypad Entry Delay All Systems Once the entry delay starts, the keypad sounds an entry tone and displays ENTER CODE: - . Present your card to the reader. Once validated, the system disarms all areas accessible by you and activates the 9863 Door Strike relay. Area systems provide a delay to allow selected areas only to be disarmed.
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Specifications Operating Voltage Dimensions 12 Vdc 5.8” W x 4.135” H x 0.6” D Compatibility All keypads are compatible with all XR100/XR500 Series, XR150/XR350/XR550 Series, XT30/XT50 Series, and XTL Series panels.