User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsLOW POWER TRANSCEIVER

Table Of Contents

9000 Series Wireless Keypads

InstallatIon GuIde

9000 Series Wireless Keypads

Description

The DMP 9060 and 9063 are fully functioning supervised wireless keypads. They provide installation exibility while also

offering optional codeless arming and disarming capabilities. Each keypad provides:

• Custom 16-character home or business name

• Four 2-button Panic keys

• 32-character display

• Backlit keyboard with easy-to-read lettering

• Internal speaker.

• Wall tamper protection

• Keyboard and logo backlighting turns Red in alarm

conditions

The Model 9063 keypad also provides a built-in proximity card

reader designed to read DMP/HID proximity credentials for

codeless arming and disarming.

Compatibility

XTL Panels

What is Included

The 9000 Series Keypad includes the following items:

• One wireless keypad mounted in a Thinline two-part housing (base and cover)

• One 3.7V lithium battery

• One 12 VDC DC Plug-in Power Supply

• Serial number label

Keypad Serial Number

For your convenience, an additional pre-printed serial number label is included. Prior to installing the device, record the

serial number or place the pre-printed serial number label on the panel programming sheet. This number is required during

programming. As needed, use the zone name and number label to identify a specic transmitter.

Programming the Transmitter in the Panel

The 9000 Series Wireless Keypads can be programmed into the XTL through panel programming or using the wireless

keypad association mode.

Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the

receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour to send

a supervision message unless tripped, tampered, or powered up. This operation extends battery life for transmitters. A

missing message may display on the keypad until the transmitter sends a supervision message.

Device Setup Programming

Refer to the XTL Programming Guide (LT-1107) as needed. Program the keypad as a device in Device Setup during panel

programming. At the Serial Number: prompt, enter the eight-digit serial number. Continue to program the device as

directed in the panel programming guide.

Wireless Keypad Association

Pressing the XTL RESET button 3 times within 5 seconds enables the keypad association mode. For one minute the panel

listens for wireless keypads. Any keypads not already associated with another panel are assigned to the rst open keypad

address. Keypads are automatically assigned addresses based upon the order in which they are detected. A maximum of 4

keypads may be associated with a panel.

Selecting the Proper Location (LED Survey Operation)

The 9000 Series keypad provides a built-in survey capability in the Installer menu to allow one person to conrm keypad

communication with the panel. Refer to Accessing Keypad Wireless Survey later in this document.

32-Character Display

Data Entry Digit keys

COMMAND Key

Back Arrow Key

Select Keys

Backlit Logo

and Proximity

Antenna

Figure 1: 9000 Series Keypad

Summary of content (10 pages)

PAGE 1
Installation Guide 9000 Series Wireless Keypads Description The DMP 9060 and 9063 are fully functioning supervised wireless keypads. They provide installation flexibility while also offering optional codeless arming and disarming capabilities. Each keypad provides: • • • • • • • Custom 16-character home or business name Four 2-button Panic keys 32‑character display Backlit keyboard with easy-to-read lettering Internal speaker.
PAGE 2
Installing the Keypad Building Wall All DMP keypad housings are designed to easily install on any desk stand, 4” square box, 3‑gang switch box, or a flat surface. Thinline or Aqualite Keypad Remove the Cover The keypad housing is made up of two parts: the front, which contains the circuit board and keyboard components and the base. Use the following steps and figures to separate the keypad front and base. 1.
PAGE 3
Battery Replacement Standby battery connector 1. Disconnect the battery lead connector from the keypad J3 battery header. 2. Remove the battery strap from the standby battery. 3. Remove and properly dispose of the used battery. Caution: Risk of fire, explosion, and burns. Do not disassemble, heat above 212°F (100°C), or incinerate. Properly dispose of used batteries. Standby battery strap 4. Place the new battery on the keypad PCB and replace the battery strap. 5.
PAGE 4
End-User Options All keypads provide three keypad adjustments the end-user can make through a User Options Menu. The user can also view the keypad model number and address. On all keypads press and hold the Back Arrow (<—) and CMD (COMMAND) keys for two seconds to access User Options. The keypad display changes to SET BRIGHTNESS. Use the COMMAND key to display the next Option or press the Back Arrow to exit.
PAGE 5
Installer Options Menu All keypads provide Keypad Option and Keypad Diagnostic menus to allow installing and service technicians to configure and test keypad operation. Accessing Installer Options Access the Installer Options Menu through the User Options function. Hold down the Back Arrow and COMMAND keys for two seconds to display SET BRIGHTNESS. Enter the code 3577 (INST) and press COMMAND. The display changes to KPD OPT (keypad options) KPD DIAG (keypad diagnostics) and STOP.
PAGE 6
Site Code Position SITE CODE Position: 1 SITE CODE Length: 8 User CODE Position: 9 User CODE Length: 16 Enter the site code start position in the data string. Press any Select key to enter a number between 0-255. Default is 1. Site Code Length Enter the number of characters the site code contains. Press any Select key to enter a number between 1-16. Default is 8. User Code Position Define the User Code start bit position. Press any Select key to enter a number between 0-255. Default is 9.
PAGE 7
Accessing Keypad Diagnostics If necessary, refer to Access the Installer Menu earlier in this document. Keypad Diagnostics (KPD DIAG) KPD KPD KPD OPT DIAG RF STOP The Keypad Diagnostic option allows you to check the display segments, keyboard backlighting and test individual keys. Press the Select key under KPD DIAG. The keypad lights all display segments and illuminates the keyboard in Red. In approximately one second the display backlighting changes to Green.
PAGE 8
Additional Programming The 9063 keypads allow users to present a proximity credential to the built-in proximity reader. Users can also manually enter their user code into the keypad. The keypad verifies the user code and its authority with the panel. Programming Cards into the System This programming feature operates on 9063 keypads only. Access the User Menu in one of two ways.
PAGE 9
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 10
12 VDC Standby Battery 9000BAT Voltage 3.7 VDC Capacity 800Ah Type Lithium Polymer Recharable Standby Time 24 Hours See Battery Life Expectancy for full details. Frequency Range: 903-927 MHz Dimensions 7” W x 5.25” H x 0.