User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsLOW POWER TRANSCEIVER

InstallatIon GuIde

1105 Universal Transmitter

Description

The 1105 Series are two input transmitters that are typically used for door/window applications. The 1105 Series

provides an internal case tamper, internal magnetic reed switch and an on-board terminal block to allow for

external contact wiring. Both sets of contacts, internal and external, can be programmed to operate at the same

time allowing for two independent zones from one transmitter. The 1105-EOL provides one internal magnetic reed

switch, a wall tamper, and an on-board terminal block to allow for external contact wiring with an end-of-line

resistor. Refer to the panel programming guide for zone programming information.

Compatibility

All DMP 1100 Series Wireless Receivers and Panels

What is Included

The 1105 Universal Transmitter includes the following items:

• One1105TransmitterPCBmountedinatwo-parthousing

(base and cover)

• Magnetwithstandardhousingandbase

• One3VlithiumCR123ABattery

• Hardwarepack

• Zonenameandnumberlabel

• Serialnumberlabel

• OptionalCommercialmagnethousing

The 1105-EOL Universal Transmitter includes the following items:

• One1105Transmitterandallcomponentslistedabove

• OneModel312470KEOLResistor

Transmitter Serial Number

For your convenience, an additional pre-printed serial number

label is included. Prior to installing the device, record the serial

number or place the pre-printed serial number label on the panel

programming sheet. This number is required during programming.

As needed, use the zone name and number label to identify a

specictransmitter.

Programming the Transmitter in the Panel

RefertotheXR500SeriesProgrammingGuide(LT-0679),XR100

SeriesProgrammingGuide(LT-0896),ortheXT30/XT50Series

ProgrammingGuide(LT-0981)asneeded.Programthedeviceasa

zone in Zone Information during panel programming. At the Serial

Number:prompt,entertheeight-digitserialnumber.Continueto

program the zone as directed in the panel programming guide.

Note: When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset.

If the receiver has been powered down for more than one hour, wireless transmitters may take up to an additional

hour to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life for

transmitters. A missing message may display on the keypad until the transmitter sends a supervision message.

Selecting the Proper Location (LED Survey Operation)

The1105Transmitterprovidesabuilt-insurveycapabilitytoallowonepersontoconrmtransmittercommunication

withthereceiverwhilethecoverisremoved.The1105TransmitterPCBRedSurveyLEDturnsonwheneverdata

is sent to the receiver then immediately turns off when the receiver acknowledgement is received. Pressing the

tamperswitchisaconvenientwaytosenddatatothereceivertoconrmoperation.Whenthetamperswitch

is pressed or released, the LED blinks once to indicate proper operation. When the transmitter does not receive

an acknowledgement from the receiver the LED remains on for about 8 seconds to let you know communication is

notestablished.CommunicationisalsofaultywhentheLEDashesmultipletimesinquicksuccession.Relocate

the transmitter or receiver until the LED immediately turns off indicating the transmitter and receiver are

communicatingproperly.Propercommunicationbetweenthetransmitterandreceiverisveriedwhenforeach

press or release of the tamper switch, the LED blinks immediately on and immediately off.

RepeatthistesttoconrmveseparateconsecutiveLEDblinks.Anyindicationotherwise

means proper communication has not been established.

Figure 2: 1105 PCB Layout

Battery

Location

Internal Contact Magnetic

Reed Switch

External

Contact

Terminal

Block

Tamper

Switch

Mounting

Hole

Mounting

Hole

Red Survey

LED

Figure 1: Mounted Transmitter and Magnet

Standard Magnet Housing

1105 Universal Transmitter

Insert small screwdriver

and twist to remove cover

Summary of content (4 pages)

PAGE 1
Installation Guide 1105 Universal Transmitter Description The 1105 Series are two input transmitters that are typically used for door/window applications. The 1105 Series provides an internal case tamper, internal magnetic reed switch and an on-board terminal block to allow for external contact wiring. Both sets of contacts, internal and external, can be programmed to operate at the same time allowing for two independent zones from one transmitter.
PAGE 2
Mounting the Transmitter and Magnet Assemblies For internal contact operation, the transmitter and magnet assembly should have no more than 1/2" space between the assembled housings after installation. When mounting on metal (ferrous) surfaces, this distance is slightly less. For door installations, it is recommended the transmitter be mounted on the door frame and the magnet assembly be mounted on the door. Magnet Assembly Only one magnet assembly is required for internal reed switch operation.
PAGE 3
1105 External Contact Mounting When connecting an external contact to the terminal block, DMP recommends using 18 or 22-gauge unshielded wire. Do not use twisted pair or shielded wire. Connect the external contact as normally open (N/O) or normally closed (N/C) without any end-of-line resistor. Refer to the Contact option under Zone Information in the appropriate panel programming guide. Note: When using both the internal reed switch and external terminal block, you must use consecutive zone numbers.
PAGE 4
Battery Life Expectancy Typical battery life expectancy for DMP Model 1105 wireless transmitters is 5 years. DMP wireless equipment uses two-way communication to extend battery life. The following situations can reduce battery life expectancy: • If a receiver is unplugged or not installed. Note: Transmitters continue to send supervision messages until a receiver returns an acknowledgement. After an hour the transmitter only attempts a supervision message every 60 minutes.