Installation Guide

ManualsBrandsDigital Monitoring Products ManualsElectronicsLife Safety and security wireless receiver.

1100DH SERIES HIGH POWER

WIRELESS RECEIVERS

Installation Guide

Figure 1: 1100DH High Power

Wireless Receiver

R Y G B TO PANEL

The 1100DH Series Wireless Receiver

provides up to 32 wireless zones for

XT30/XT50 Series panels. The 1100DHE

features 128-bit AES encryption.

The 1100DH Series provides two-way,

supervised communication using

900 MHz frequency hopping spread

spectrum technology.

The 1100DH contains additional transmit

and receive ampliﬁers to enable greater

distances for 1100 Series operation

for harsh building environments.

The additional gain introduced by

this ampliﬁcation may inhibit proper

communication with 1100 Series

transmitters located within 4ft of the

receiver. This distance may be 8ft

when using the 1122 PIR or 9000 Series

Wireless Keypads.

The system is designed so only one

1100DH is used per panel.

Compatibility

• XT30 Series panels

• XT50 Series panels running

ﬁrmware Version 102 or higher

• Encryption requires panel

Version183 or higher

• 1100T Translator requires receiver

ﬁrmware Version 207/301 and

higher

What is Included?

• One 1100DH Wireless Receiver

• Hardware Pack

PROGRAM THE PANEL

Refer to the panel programming guide as needed.

1. Reset the panel.

2. At a keypad, enter 6653 (PROG) to access the

PROGRAMMER menu.

3. In SYSTEM OPTIONS, program a HOUSE CODE

between 1 and 50. See House Code Explained for more

information.

4. If you are programming an XT50 Series panel, select NO

at the BUILT IN 1100 WIRELESS prompt to allow the

panel to use the 1100DH for wireless communication.

5. (1100DHE only) At the 1100 ENCRYPTION prompt,

select ALL to only add encrypted wireless devices to

the system. Select BOTH to allow both encyrpted and

non-encrypted wireless devices to be programmed.

6. (1100DHE only) The default passphrase appears at

the ENTER PASSPHRASE prompt. Press CMD to keep

the default. Press any select key or area to change the

passphrase and enter an 8-character hexidecimal string

(0-9, A-F).

7. Press CMD until STOP displays and press a select key or

area to save and exit the Programmer.

DESCRIPTION

SELECT A LOCATION

The receiver should be centrally located between the DMP panel

and the 1100 Series transmitters used in the installation based

on the wiring specifications below. Use an 1106 Series Universal

Wireless Transmitter to perform an LED survey.

1. With the cover removed, hold the transmitter in the

desired location.

2. Press the tamper switch to send data to the panel and

determine if communication is conﬁrmed or faulty.

Confirmed: If communication is confirmed, for each

press or release of the tamper switch, the LED blinks

immediately on and immediately off.

Faulty: If communication is faulty, the LED remains on

for about 8 seconds or flashes multiple times in quick

succession. Relocate the receiver until the LED confirms

clear communication.

Summary of content (4 pages)

PAGE 1
100DH SERIES HIGH POWER WIRELESS RECEIVERS Installation Guide 1 PROGRAM THE PANEL Refer to the panel programming guide as needed. 1. Reset the panel. 2. At a keypad, enter 6653 (PROG) to access the PROGRAMMER menu. 3. In SYSTEM OPTIONS, program a HOUSE CODE between 1 and 50. See House Code Explained for more information. 4. If you are programming an XT50 Series panel, select NO at the BUILT IN 1100 WIRELESS prompt to allow the panel to use the 1100DH for wireless communication.
PAGE 2
3 WIRE AND MOUNT THE RECEIVER The panel immediately recognizes the 1100DH if the panel is programmed with a house code. Do not use shielded wire between the panel and receiver. 1. Connect the red, yellow, green, and black wires to the PANEL terminal on the 1100DH. 2. Connect the other end of the wires to the terminals 7, 8, 9, and 10 on the panel. See Figure 2 3. Use the included #6 screws to secure the 1100DH to the surface. See Figure 2 for mounting hole locations. 4. Snap the cover back on to the base.
PAGE 3
1100DH LED Operation The six labeled LEDs on the 1100DH PCB display wireless receiver operation and activity. See Figure 2 for LED locations and Table 2 for LED indications. House Code Explained The house code identifies the panel, receiver, and transmitters to each other. The 1100DH automatically sends the specified house code to wireless transmitters when transmitter serial numbers are programmed into the panel.
PAGE 4
FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons.