User Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsRFID READER FOR ALARM SYSTEM KEYPAD

INSTALLATION SHEET

693, 791, 793 Easy Entry™ Keypads

Description

The DMP 693, 791, and 793 Easy Entry™ LCD Keypads are the industry’s Þ rst burglary/Þ re keypads with integrated

access control capability.

Each keypad provides three 2-button Panic keys, an AC power LED, an Armed LED, 32-character display, backlit

keyboard with easy-to-read lettering and an internal speaker. The 791 and 793 also provide four fully programmable

Class B, Style A protection zones you can program for a variety of burglary, Þ re, and access control applications.

Removing the Base

The keypad housing is made up of two parts: the front, which contains the circuit board and other components, and

the base. To remove the base, insert a ß at screwdriver into one of the openings on the bottom and gently twist

while pulling the halves apart. Repeat with the other opening.

Installing the Keypad

The Easy Entry keypads each use the same plastic housing. They both are designed to easily install on any 4” square

box, 3-gang switch box, 695 and 696 backbox, or ß at surface. Figure 1 shows the mounting hole locations on the

keypad base.

Harness Wiring

The 693 is supplied with one 4-wire data bus harness and one 5-wire output reader harness. The 791 and 793

keypads are each supplied with one 12-wire data bus/zone harness and one 5-wire output/reader harness. The

harness connections and color codes are shown in Figure 1.

Surface and Backbox

Mounting Holes

Combined 4-square

adn 3-gang switch box

Mounting Holes

Keypad Base Back

Surface and Backbox

Mounting Holes

1K EOL

Green/White – Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Data Bus (693) — Ground (791/793)

Green – Receive Data (693/791/793)

Yellow – Send Data (693/791/793)

Red – Keypad Power (693) — Auxiliary Power (791/793)

– Zone 4

– Zone 3

– Zone 2

– Zone 1

Output

Reader

791/793

Figure 1: Keypad Back showing Wiring Harness assignments

Wiring SpeciÞ cations

When planning an installation, keep in mind the following four speciÞ cations:

1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do Not use

twisted pair or shielded wire for LX-Bus and keypad bus data circuits. To maintain auxiliary power integrity

when using 22-gauge wire do not exceed 500 feet. When using 18-gauge wire do not exceed 1,000 feet.

Install an additional power supply to increase the wire length or add devices.

2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of the wire gauge. This

distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than

2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases.

Summary of content (8 pages)

PAGE 1
INSTALLATION SHEET 693, 791, 793 Easy Entry™ Keypads Description The DMP 693, 791, and 793 Easy Entry™ LCD Keypads are the industry’s Þrst burglary/Þre keypads with integrated access control capability. Each keypad provides three 2-button Panic keys, an AC power LED, an Armed LED, 32-character display, backlit keyboard with easy-to-read lettering and an internal speaker.
PAGE 2
3. Maximum number of devices per 2,500 feet circuit is 40. Note: Each panel allows a speciÞc number of supervised keypads. Add additional keypads in the unsupervised mode. Refer to the panel installation guide for the speciÞc number of supervised keypads allowed. 4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the voltage at any device is less than the required level, add an auxiliary power supply at the end of the circuit.
PAGE 3
Door Contact Zone with Soft-Shunt™ If the door being released by the keypad is protected, you can provide a 40-second shunt by connecting its contact to zone 2 (White/Red pair) on the keypad and enabling the Soft-Shunt feature. See ACTIVATE ZONE 2 SHUNT and Door Strike Relay Operation in this document. Once the door strike relay is activated, the user has 5 seconds to open the door connected to zone 2. The zone is then shunted for 40 seconds. Door contacts may be N/C or N/O.
PAGE 4
Volume Level Set the keypad internal speaker volume level for key presses and prewarn conditions. During alarm and trouble conditions, the volume is always at maximum level. Use the left Select key to decrease the keypad volume and the right Select key to increase the volume. Press the COMMAND key to display the Model Number. Model Number The LCD displays the model number, the version and date of the keypad Þrmware. The user cannot change this information in User Options.
PAGE 5
Entering Non-Alphanumeric Characters When in the Installer Options Menu, each key also has a special, non-alpha character you may use. These characters are not shown on the keypad. Enter a space by pressing 9 then the third Select key. The special characters available are as follows starting with the 1 digit key to the 9 digit key: ( ) ! ? / & $ ‚ ’ and - . * # for the 0 key. 1 2 3 4 ABC ( DEF ) GHI ! JKL ? 5 6 7 8 MNO / PQR & STU $ VWX , 9 0 YZ (space) ' COMMAND - .
PAGE 6
Exiting the Installer Options When done, press the COMMAND key once to return to the Installer Options screen. Press the Select key under STOP to exit the Installer Options function. Programming Cards into the System From the User Menu, select USER CODES?. Choose ADD. At the ENTER CODE: - display, present the user card to the reader. The keypad works by reading the 4 or 5-digit user code from the data sent by the access control reader.
PAGE 7
Arming and Disarming Area system Arming and Disarming. Press COMMAND, the keypad displays ARM DISARM. Press the Select key under either option. The keypad displays ENTER CODE: -. Present your card to the reader. Once validated by the system, all areas accessible by you arm or disarm automatically and the Door Strike relay activates. ABC SECURITY ARM DISARM POWER ABC SECURITY ENTER CODE: – ABC SECURITY ALL? NO YES POWER POWER Select NO to arm or disarm individual areas.
PAGE 8
Compatible Access Devices The 693, 791, and 793 Keypads are compatible with the following readers. Readers PP-6005B ProxPoint Plus MP-5365 MiniProx PR-5455 ProxPro II MX-5375 Maxi-Prox TL-5395 ThinLine II Standby Current 30mA 20mA 25mA 200mA 20mA Peak Current 75mA 110mA 125mA 700mA 115mA Current Draw Keypad Voltage Normal Standby Alarm 693 791 793 8 VDC 14.5 VDC 8 VDC 14.5 VDC 46mA 77mA 62mA 92mA + + + + 1.6mA 1.6mA 1.6mA 1.