User Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsWireless PIR

17164

DESCRIPTION

Figure 1: 1122 Wireless PIR

Motion Detector

PROGRAM THE PANEL

When programming the 1122 in the panel, refer to the panel

programming guide as needed.

1. In ZONE INFORMATION, enter the wireless ZONE number.

2. Enter the ZONE NAME.

3. Select NT (Night) as the ZONE TYPE.

4. Select the AREA.

5. At the NEXT ZONE prompt, select NO.

6. Select YES when WIRELESS? displays.

7. Enter the eight-digit SERIAL# and press CMD.

8. Enter the SUPRVSN TIME and press CMD.

9. Choose whether or not to enable DISARM DISABLE.

Note: Selecting YES allows the 1122 to be disabled for

Night and Exit type zones while the area is disarmed.

10. Choose either 2 or 4 for the PULSE COUNT.

Note: The pulse count is the number of pulse inputs

(trips) the 1122 needs to sense before going into alarm.

11. Choose either LOW or HIGH for the SENSITIVITY.

Note: Selecting LOW sensitivity may reduce false alarms

for installations in harsh environments.

12. Choose whether or not to enable PET IMMUNITY.

13. At the NEXT ZONE prompt, select YES if you are ﬁnished

programming the zone. Select NO if you would like to

access additional programming options.

INSTALL THE BATTERY

Use only a 3.0V lithium battery, DMP Model CR123A, or the

equivalent battery from a local retail outlet. Keep in mind, when

setting up a wireless system, program zones and connect the

receiver before installing batteries in the transmitters.

1. Remove the holding screw at the lower end of the 1122

case and gently lift o the cover.

2. Observing polarity, place the battery in the holder and

press into place. See Figure 2 for the battery location.

The 1122 Wireless PIR Motion

Detector uses passive infrared

technology to detect motion in a

wide angle lens pattern.

The 1122 also features an internal

case tamper, survey LED, and low

battery indicator.

Pet immunity is available for animals

up to 55 pounds and can be turned

on or o. Disarm/disable, pulse

count, and adjustable sensitivy are

also oered on the 1122.

Compatibility

All DMP 1100 Series Wireless

Receivers and burglary panels.

What is Included?

• One 1122 Wireless

PIR Motion Detector

• One 3V lithium

CR123A battery

Figure 2: 1122 Housing and PCB

Battery

Location

Tamper

Switch

Survey LED

PCB

Screw

1122 WIRELESS PIR MOTION DETECTOR

Installation Guide

Summary of content (4 pages)

PAGE 1
122 WIRELESS PIR MOTION DETECTOR Installation Guide 1 PROGRAM THE PANEL When programming the 1122 in the panel, refer to the panel programming guide as needed. Figure 1: 1122 Wireless PIR Motion Detector 1. In ZONE INFORMATION, enter the wireless ZONE number. 2. Enter the ZONE NAME. 3. Select NT (Night) as the ZONE TYPE. 4. Select the AREA. 5. At the NEXT ZONE prompt, select NO. 6. Select YES when WIRELESS? displays. 7. Enter the eight-digit SERIAL# and press CMD. 8.
PAGE 2
3 SELECT A LOCATION The 1122 provides a survey capability to allow one person to confirm communication with the wireless receiver or panel while the cover is removed. This allows you to easily determine the best location for the 1122. Location Dos • Do locate on a rigid vibration-free surface • Do locate so that the expected intruder's movement will be across the detection pattern • Do locate between 4.9 and 8.2 feet high.
PAGE 3
5 MOUNT THE 1122 Prior to permanently mounting the 1122, check that it is properly communicating with the panel. See the Select a Location and Test Communication to the Panel sections. 1. Remove the holding screw at the lower end of the 1122 case and gently lift off the cover. 2. Loosen the screw located on PCB and slide the PCB out of the unit. 3. Place the 1122 against the wall and screw through the appropriate mounting holes.
PAGE 4
FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons.