LevelOne WPC-0600 N_One Wireless CardBus Adapter User Manual V1.0.
Table of Contents CHAPTER 1 INTRODUCTION...................................................................................... 1 Package Contents ................................................................................................ 1 LEDs....................................................................................................................... 1 Operation...............................................................................................................
Chapter 1 Introduction This Chapter provides an overview of the Wireless Adapter's features and capabilities. Congratulations on the purchase of your new Wireless Adapter. The Wireless Adapter provides a wireless network interface for your Notebook or PC. Package Contents The following items should be included: • WPC-0600 • Quick Installation Guide • CD Manual/Driver/Utility If any of the above items are damaged or missing, please contact your dealer immediately.
Chapter 2 Initial Installation This Chapter covers the software installation of the Wireless Adapter. Requirements • Windows 2000/XP/Vista • CardBus Card Slot • CD-ROM Drive. • IEEE802.11n, IEEE802.11b or IEEE802.11g Wireless LAN. Procedure You should install the supplied software BEFORE inserting the Wireless Adapter. 1. Insert the CD-ROM into the drive on your PC. 2. The installation program should start automatically. If it does not, run autorun.exe program. 3.
N_One Wireless CardBus Adapter Figure 2: Installation Screen 6. Click "Continue Anyway" on the screen above. Figure 3: Information 7. Press the Cardbus Card firmly into the slot, then click "OK". 8. The Windows "New Hardware" wizard will then start. • Select Install the software automatically to allow it to complete the installation of the Windows driver • If using Windows XP, you may see a warning screen like the example below.
N_One Wireless CardBus Adapter 9. When the Windows wizard is complete, you will now have a new icon in your system tray, as shown below. Figure 5: System Tray Icon Wireless Adapter Icon Table Connection to the Wireless Adapter is established. The length of green color indicates the signal strength. No connection to the Wireless Adapter. The Wireless Adapter is unplugged. 10. You can double- click this icon to configure the Wireless interface. See the following chapter for details.
Chapter 3 Using the Windows Utility This Chapter provides Setup details for the AP mode of the Wireless Adapter. Overview If using Windows, you can use the supplied utility to configure the Wireless interface. To Use the supplied Windows utility for Configuration • Right-click the System Tray icon • From the pop-up menu, select "Restore". This Chapter assumes you are using the supplied WPC-0600 Wireless LAN Utility.
N_One Wireless CardBus Adapter Connecting to a Wireless Network Double-click the Icon to open the Site Survey screen, when you can select the Wireless network you wish to join. Auto Connect Normally, this option should be enabled. The adapter will then connect to an available network which was connected successfully last time. There are various methods to specify the required network. • On the Profile Manager tab, select the desired profile in the list, and click the Apply Profile button.
N_One Wireless CardBus Adapter Display 802.11g Access Points Select this check box to display 802.11g (infrastructure) networks. Network Name Available wireless networks are listed. MAC Address This is the MAC address of the Access Point (or Wireless station, if the network is an Ad-hoc network). Security Data encryption and authentication methods used on the wireless network CH. The channel used by the Wireless network. Signal This is displayed as percentage (0 ~ 100%).
N_One Wireless CardBus Adapter Profile Manager Screen This screen is accessed by clicking the Profile Manager tab on the main screen. Figure 9: Profile Manager Screen Data - Profile Manager Screen Profile Name Enter or select a suitable name for this profile. Each profile must have a unique name before user can actually save the profile. Network Name (SSID) If the desired wireless network is currently available, you can select its SSID. Otherwise, type in the SSID of the desired wireless network.
N_One Wireless CardBus Adapter Prefer Channel Select the channel you would like to use under Ad-Hoc mode. Channel 1 ~ 13. Authentication Mode You MUST select the option to match the Wireless LAN you wish to join. The available options are: Encryption Method • Open System - Broadcast signals are not encrypted. This method can be used only with no encryption or with WEP. • Shared Key - Broadcast signals are encrypted using WEP. This method can only be used with WEP.
N_One Wireless CardBus Adapter 802.1x Authentication Protocol For WPA Radius and WPA2 Radius modes, select the desired option in the drop-down list. Configure WPA Radius For WPA Radius and WPA2 Radius modes, click this button to open a sub-window where you can enter details of the Radius Server. To add a profile 1. On the Profile Manager tab, complete the settings on this screen. (Please make sure to specific the Profile name) 2. Verify that the settings you configured are correct. 3.
N_One Wireless CardBus Adapter Advanced Settings Screen Once you have created a profile, as described above, the Advanced Settings tab will be available on the Profile Manager screen. Note: Advanced settings only available when 11b/g wireless mode has been selected. Figure 10: Advanced Settings Screen Data - Advanced Settings Screen Do not change settings Enable this check box if you don’t want to modify the settings in this screen. Preamble (2.4GHz) Normally, this should be left at "Auto".
N_One Wireless CardBus Adapter Channel Width The value is set as “Auto” Guard Interval This value is set as "Auto" Extension Channel Auto selects the wireless channel. The value is set to “Auto” It will auto select the most suitable channel. Antenna Selection The default value is set to "Auto".
N_One Wireless CardBus Adapter Network Status Screen This screen displays the status of the current wireless link. Clicking the Network Status tab will display a screen like the following. Figure 11: Network Status Screen You may have to wait a few seconds for the screen to be populated. Data - Network Status Screen Link Information Current Status It will indicate the current link status. Network SSID It shows the SSID or network name of the selected wireless network.
N_One Wireless CardBus Adapter Default Gateway Gateway IP address associated with the current IP address. DHCP Server It shows the IP address of the DHCP Server. Channel Performance Channel Performance It graphically presents the Transmission (Tx) rate and Receiving (Rx) rate over time. Signal Signal It graphically presents the Signal strength. The Channel Performance diagram indicates the real time TX and RX.
Appendix A Specifications Wireless Adapter Model: LevelOne WPC-0600 N_One Wireless CardBus Adapter Standards: IEEE 802.11b, IEEE 802.11g, Draft 802.11n compliant Computer Slot Type: CardBus Card 20 MHz BW: 130, 117, 104, 78, 52, 39, 26, 13 Mbps 40 MHz BW: 270, 243, 216, 162, 108, 81, 54, 27 Mbps (802.11n) Data Rates: 54, 48, 36, 24, 18, 12, 9, and 6 Mbps (802.11g) 11, 5.5, 2, 1 Mbps (802.11b) Operating Channels: 11 for North America, 13 for Europe and Japan Operating Frequency: 2.4 ~ 2.
Appendix B About Wireless LANs This Appendix provides some background information about using Wireless LANs (WLANs). Modes Wireless LANs can work in either of two (2) modes: • Ad-hoc • Infrastructure Ad-hoc Mode Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless Stations (e.g. notebook PCs with wireless cards) communicate directly with each other. Infrastructure Mode In Infrastructure Mode, one or more Access Points are used to connect Wireless Stations (e.g.
N_One Wireless CardBus Adapter Channels The Wireless Channel sets the radio frequency used for communication. • Access Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least interference and best performance. In the USA and Canada, 11 channels are available. If using multiple Access Points, it is better if adjacent Access Points use different Channels to reduce interference.
N_One Wireless CardBus Adapter CE Marking Warning Hereby, Digital Data Communications, declares that this (Model-no. WPC-0600) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The CE-Declaration of Conformity can be downloaded at: http://www.levelone.eu/support.
Regulatory Approvals FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
