TM AD-24 ANALOG INPUT & DIGITAL CONVERTER USER GUIDE 1266 Park Road Chanhassen, MN 55317 952-401-7700 support@digitalaudio.com www.digitalaudio.com Version 1.
SAFETY INSTRUCTIONS TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. CONTACT DIGITAL AUDIO LABS FOR SERVICING. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated and/or potentially dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CONTENTS Safety Instructions................................................................................................. ii Important Safety Instructions.................................................................... ii Care.......................................................................................................... ii Digital Audio Labs Limited Warranty..................................................................... 1 Repair Policy................................................
DIGITAL AUDIO LABS LIMITED WARRANTY Digital Audio Labs warrants their products against defects in material and workmanship for a period of two years from date of purchase. During this period, Digital Audio Labs will, at its option, repair the defective unit or replace it with a new or rebuilt one. The warranty does NOT cover: • Damage due to abuse, misuse, or accident. • Damage due to operation contrary to the instructions in the product instruction manual.
CONTENTS OF BOX • AD-24 • External 12VDC Power Supply INTRODUCTION The Livemix AD-24 is the analog input component for the Livemix system. The AD-24 receives line level audio signals from a mixer, snake, or interface and converts them to the Livemix Data format. Livemix audio data is sent from the AD-24 to the MIX-16 over a single shielded CAT5 or CAT6 network cable.
ANATOMY OF THE AD-24 FRONT LIVEMIX DATA 2 REAR 8 AD-24 5 6 AD-24 3 LIVEMIX DATA OUT 4 7 12VDC 3.33A 1 1. External Power Supply Connector: Connect the included external power supply to this jack. Make sure to only use the power supply that is supplied with your AD-24. 2. Power Switch: This switch turns on the power to the AD-24. 3. ¼” TRS Inputs: These connectors accept a balanced or unbalanced line-level signal from your analog audio source.
5. Input Lights: These lights give you a visual indication of the incoming audio signal level. Use the signal level lights as a guide, when adjusting the output volume of the signal sources that are feeding the inputs of the AD-24. The input lights can be one of three colors based on signal strength: -20dB (Green): A green light indicates a healthy signal level, and is where you want to see your signal strength most of the time.
SETUP DIAGRAMS Connecting the AD-24 to a Mixer/Snake/Interface ANALOG MIXER/SNAKE/INTERFACE ANALOG MIXER/SNAKE/INTERFACE DB25 CABLE (TASCAM PINOUT) TRS CABLE TRS CABLE DB25 CABLE (TASCAM PINOUT) AD-24 LIVEMIX DATA OUT AD-24 LIVEMIX DATA OUT 12VDC 3.33A 12VDC 3.33A LIVEMIX DATA AD-24 LIVEMIX DATA AD-24 Connecting the AD-24 to the MIX-16 AD-24 LIVEMIX DATA OUT AD-24 LIVEMIX DATA OUT 12VDC 3.33A 12VDC 3.
SETUP AND OPERATION The AD-24 will most likely be installed in a rack near the mixer, but this is not required. The MIX-16 will likely be placed near the stage. A single shielded CAT5 or CAT6 cable will connect the AD-24 to the MIX-16 and transmit all the necessary audio data for creating personal mixes. 1. Attach the external Power Supply to the AD-24 External Power Supply connector. 2. Connect the AD-24 to the analog signal source. • Either balanced TRS or DB-25 connections are acceptable.
LIVEMIX SYSTEM OVERVIEW There are three components required to make a Livemix system. Each system will have either an analog or digital input unit, a central mixer unit, and at least one attached control surface. Input Options Users with analog source material will use the AD-24. Using the TRS or DB-25 inputs, audio from the source material is made available to the Livemix system. Users with digital source material will use the Dante Option Card (LM-DANTE-EXP).
TROUBLESHOOTING My AD-24 is not turning on, and I do not see the power light illuminating. Check to make sure that you have the AD-24’s external power supply connected to a working power outlet. I do not see the Livemix Data light illuminating, on the front panel. If the Livemix Data light is not illuminating, there is a problem with the power to the AD-24. Check to make sure that the power supply is connected to the AD-24 and that all the cables are secure.
APPENDIX TASCAM DB-25 pin out LIVEMIX AD-24 9
LIVEMIX SUPPORT Phone Support: Toll Free: Email Support: Website: 952-401-7700 844-DAL-INFO support@digitalaudio.com www.digitalaudio.com/support DIGITAL AUDIO LABS 1266 Park Rd Chanhassen, MN 55317 TECHNICAL SPECIFICATIONS AD-24 (ANALOG CHARACTERISTICS) THD+N .001% S/N Ratio 111 dB Frequency Response 20 Hz – 22KHz ± .5dB Crosstalk -92 dB Maximum Input Level +24 dBu (minor distortion above 23.
© 2014 Digital Audio Labs. Audinate®, the Audinate logo and Dante are trademarks of Audinate Pty Ltd. Livemix is a trademark of Digital Audio Labs. Patents pending.