DWM‐1000 User’s Guide Digital Wireless Microphone Copyrighted ©2007‐2008, Digital Ally, Inc. All Rights Reserved, Printed in U.S.A. This publication may not be reproduced, stored in a retrieval system, or transmitted in whole or part in any form or by any means electronics, mechanical, recording, photocopying, or in any manner without prior approval of Digital Ally, Inc. Digital Ally DWM‐1000 User’s Guide 1500.0009.00.
DWM‐1000 User’s Manual Digital Wireless Microphone Table of Contents 1.0 Introduction – The Wireless Microphone (RMT)…………………………….………..page 3 2.0 System Components……………………………………………………………..……….page 3 3.0 RMT Controls……………………………………………………………………....……….page 4 4.0 Charging………………………………………………………………………….…………page 4 5.0 Power Slide Switch………………………………………………………………....……..page 5 6.0 LED Indicators…………………………………………………………….………..…..…..page 5 7.0 Synching the RMT with the DVM……………………………….…………………...…..page 5 8.
DWM‐1000 User’s Manual Digital Wireless Microphone 1.
DWM‐1000 User’s Manual Digital Wireless Microphone 3.0 RMT Controls Belt Clip Status LEDs Internal Microphone Transmit Power Switch OFF‐Up ON‐Down Mic / Headphone Charger Jack Covert Mode Switch ON‐Up OFF‐Down Button 1 USB / Charger Jack Button 2 Memo Charger Contacts 4.0 Charging Note: The RMT will need to be fully charged before initial use.
DWM‐1000 User’s Manual Digital Wireless Microphone 5.0 Power Slide Switch To power the RMT ON, slide the power switch up. When the RMT is powered ON, the green LED will flash every 3 seconds while in the Standby Mode. Sliding the power switch down will turn the RMT OFF. 6.0 LED Indicators The LEDs indicate the current operating status of the RMT.
DWM‐1000 User’s Manual Digital Wireless Microphone 7.4 Press and hold button 1 and 2 on the RMT until the red, yellow, and green LEDs begin to flash. 7.5 Press the MENU button on the DVM to begin Synching. 7.6 Note: Once the Wireless Mic is detected, Synching will begin. 7.7 Once Synching is Successful, press the MENU button to continue. 7.8 Note: Repeat the above procedure to Synch an additional RMT to the DVM. 8.0 Transmitting Audio The RMT can be used to transmit audio and initiate a recording.
DWM‐1000 User’s Manual Digital Wireless Microphone 9.4 To select playback with multiple record sessions present: press and hold the MEMO and 1 button. The red, yellow, and green LEDs will illuminate for 1 second. To playback the most recent recording: The green LED will flash followed by a 3 second pause. Pressing the MEMO button during this first pause will begin playback. To playback the second most recent recording: After the three second pause, the green LED will flash once again.
DWM‐1000 User’s Manual Digital Wireless Microphone 12.0 GPS (Global Positioning System) Enabled The RMT is WAAS GPS enabled, allowing highly accurate latitude and longitude coordinates of the RMT location to be transmitted to the DVM. The RMT GPS coordinates can be enabled via the Settings Menu on the DVM. 13.0 USB The USB jack can be used to charge the RMT utilizing a PC or the AC/USB adapter.
DWM‐1000 User’s Manual Digital Wireless Microphone 15.0 Specifications Integrated 900MHz, Frequency Hopping Spread Spectrum, Dual Receiver Capable, GPS Enabled, Remote Microphone System.
DWM‐1000 User’s Manual Digital Wireless Microphone 16.0 Limited Warranty Digital Ally, Inc. Digital Wireless Microphone is guaranteed to be free from defects in workmanship and material for a period of twenty four (24) months from the date of purchase to the original purchaser.
DWM‐1000 User’s Manual Digital Wireless Microphone 17.0 Contact Us Digital Ally, Inc. 7311 West 130th Street, Suite 170 Overland Park, Kansas 66213 website: www.digitalallyinc.com Support Email: support@digitallyinc.com Sales Email: sales@digitalallyinc.com Support Hours of Operation Monday – Friday: 8AM – 6PM (Central) (excluding holidays) Sales/Support Toll Free: 1‐800‐440‐4947 Digital Ally DWM‐1000 User’s Guide 1500.0009.00.
DWM‐1000 User’s Manual Digital Wireless Microphone This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules (and the Industry Canada (IC) Spectrum Management and Telecommunications policy, RSS 210 standard.) These limits are designed to provide reasonable protection against interference in a commercial or residential installation.
DWM‐1000 User’s Manual Digital Wireless Microphone IC RSS 210 This Radio Standards Specification (RSS) sets out the requirements for license exempt lowpower intentional radiators, defined as Category I equipment as per RSS-Gen. The applicable standard for low-power intentional radiators in Canada, for Category I equipment corresponds with FCC Part 15 Subpart C.