CANCUN 222-Mic CANCUN 442-Mic Professional USB Audio Interface Version v1.
For technical support, please contact your supplier www.digigram.com Digigram S.A. Parc de Pré Milliet, 38330 Montbonnot - FRANCE Tel: +33 (0)4 76 52 55 01• Fax: +33 (0) 4 76 52 53 07• E-mail: info@digigram.com Digigram Asia Pte Ltd. 60 Albert Street - #19-11OG Albert Complex Singapore 189969, Singapore Tel : +65 6291 2234 • Fax : +65 6291 3433 • E-mail : info_asia@digigram.
INFORMATION FOR THE USER IMPORTANT NOTICE FEATURES Cancun 222-Mic and CANCUN 442-Mic main hardware features CANCUN 222-Mic CANCUN 442-Mic Software features HARDWARE REQUIREMENTS SUPPORTED OPERATING SYSTEMS HARDWARE INSTALLATION SOFTWARE INSTALLATION OF CANCUN UNDER WINDOWS FIRMWARE UPDATE SETTING AND MONITORING CANCUN PARAMETERS FROM THE CONTROL PANEL Starting the control panel Configuration of Preferences Adjusting the gains on the analog inputs and displaying vu-meters Input pad and 48V phantom power Disp
INFORMATION FOR THE USER The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with part 15 of FCC rules.
CANCUN devices are delivered with a ‘Y’ USB cable allowing powering the device from two USB ports. It is recommended to connect the two USB plugs so as to correctly power the CANCUN unit. Cancun 222-Mic and CANCUN 442-Mic main hardware features ● ● ● ● ● ● ● ● ● ● ● ● Simultaneous analog & AES I/Os in a compact form factor A/D and D/A conversions 24-bit / frequency : 32 kHz, 44.1 kHz, 48 kHz, 88.
CANCUN 442-Mic ● ● ● ● ● 4 balanced analog mono line/mic inputs, +25 dBu max signal level 4 balanced analog mono line outputs, +10 dBu max signal level 2 additional balanced AES/EBU inputs 2 additional balanced AES/EBU outputs 1 stereo headphone output on female 6.35mm jack Software features ● ● ● ● ● ● ● ● CANCUN 222-Mic and CANCUN 442-Mic comply with the USB Audio 2.
It will then automatically be detected by the operating system. Under Windows operating systems, it is necessary to install the driver package for Windows (because Windows OS don’t support USB Audio 2.0). ● ● Notes: It is recommended to plug the two USB connecors of the provided ‘y’ USB cable. It is not recommended to power CANCUN from a USB power supply.
Accept the License Agreement, and click on Next. By default, driver files are installed in folder C:\Program Files\Digigram CANCUN. Select another folder if you want, and click on Install. Wait during the installation of the driver.
When the message “Preinstallation was successful. Click Next to continue” is displayed, click on Next. Click on Finish to finish the installation procedure. The Cancun DirectSound devices are now listed in the Windows “Sound” control panel, in “Playback” and “Record” tabs. The ASIO devices can be selected from any ASIO application.
FIRMWARE UPDATE Your Cancun is delivered with a firmware version applied in factory. A more recent firmware version may have been released by Digigram since you purchased your CANCUN (a new firmware may include improvements and new features). Please connect to the Support page of Digigram WEB site: www.digigram.com/drivers/index.php. Select “Sound cards” in section “Product Technology”, and then select “CANCUN 222-Mic or CANCUN 442-Mic” from section “Product type”.
A confirmation window is displayed. Click on button “Yes” to confirm the firmware update. The displayed green bar indicates the firmware update progress. When the green progress bar has reached 100% and the message “The Firmware was successfully updated” is displayed, click on button “Exit” to quit the firmware updater application. You can now use your CANCUN which is running the new firmware.
SETTING AND MONITORING CANCUN PARAMETERS FROM THE CONTROL PANEL Starting the control panel Cancun parameters can be set from its control panel. To open Cancun control panel, go in Start menu, Programs, Digigram CANCUN, and select Cancun Control Panel. Note that the Control Panel is automatically opened when connecting the CANCUN to the PC (provided that the driver has been installed under Windows).
Click on to set the global parameters of CANCUN. Cards: allows select the CANCUN device to set its parameters. Clocks: allows selecting the sampling clock: · Internal: sampling clock is generated internally · AES1: sampling clock is extracted from digital input AES1. Without digital signal connected to the input “AES 1”, AES1 clock selection is displayed as “not valid”. · Buffers: these parameters allow adjusting the latency of the CANCUN device.
Click on to set the parameters of audio inputs. Each slider allows adjusting the analog gain for an analog input from 0dB to + 55 dB, by 1 dB steps. It is possible to adjust the level of several inputs at the same time, by moving only one slider. To do so, press “Shift + Click” on each slider. The cursor of the slider becomes purple. When all the selected sliders are purple, just move one of them.
48 V phantom power on the input the mic is connected to. To activate the 48V phantom power on an input, click on the OFF button on the right of 48V for the concerned input: . When 48V is enabled on an input, the button is displayed as follows: Note that any modification of the Pad from the software Control Panel is reflected on the touch pad of Cancun, and vice versa.
Adjusting the gains on the analog outputs and displaying vu-meters Click on the icon to set the parameters for audio outputs. For each output, the volume slider allows adjusting the analog attenuation, 0dB to - 72 dB, by 1 dB steps. It is possible to adjust the volume of several outputs at the same time, by moving only one slider. To do so, press “Shift + Click” on each slider. The cursor of the slider becomes purple. When all the selected sliders are purple, just move one of them.
Configuration of headphone output parameters Click on the icon to adjust the settings of the headphones output. The central fader allows adjusting the signal level on the headphones output. The horizontal cursor, in top of the main fader, allows adjusting the balance between left and right channels. The heaphones output receives a mix composed of: - all the inputs (analog and AES/EBU) - all the audio played on CANCUN output devices (playback from software applications).
Click on the icon on the bottom left of the central headphones window to access the DIGITAL OUTPUT section, for adjusting the levels of the signals played on the AES/EBU outputs from a software application.
SETTING CANCUN PARAMETERS FROM THE CANCUN TOUCH PANEL Input gains setting Pad Press the Pad touch button to enable/disable the fixed attenuation on the desired. When PAD is ON, a green led appears. An attenuation of -30.0 dB is applied to the analog input signal. When PAD is OFF, the LED is turned off. No attenuation is applied. Note that the Pad status is reflected in the software Control Panel.
Output gains settings The analog output gain is adjustable with the upper rotary button when: · the IN/OUT touch button on the right of the rotary button is in position OUT (green led in front of OUT) · and the touch button on the left of the rotary wheel is active (green led). Pressing the button several times allows selecting analog output 1, analog output 2, both outputs, or no output (LED turned off). The analog gain adjustment is then applied to the selected output(s).
SPECIFICATIONS Configuration Bus Format USB 2.0 / Compliant with the USB 2.0 Audio specification Size 254 mm x 96 mm x 36 m Operating : temp / Humidity 0°C to +50°C / 0 % to 90 % (non condensing) Audio specifications A/D and D/A converters resolution 24 bits Sampling frequencies available 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 192 kHz Audio formats supported PCM 8, 16, 20, and 24 bits Latency 3.4 mS Analog-to-PC or PC-to-Analog (Windows 7 / 64 bits) 3.
AES11 synchronization Other inputs Yes, on AES 1 Input Yes, on AES 1 Input ADAT / S/PDIF* ADAT / S/PDIF* * Not implemented yet. This will be available by software upgrade. Outputs CANCUN 222-Mic CANCUN 442-Mic 2 balanced 4 balanced +10 dBu / 2x33 Ohms +10 dBu / 2x33 Ohms 1 AES/EBU 2 AES/EBU From 0 to -72 dB by 1 dB steps From 0 to -72 dB by 1 dB steps Dedicated output stage, >10 mW from 32 to 600 Ohms Bandwidth: 10Hz-20 kHz +-0.
Channel phase difference (A/D Input and D/A Output) · +- 0.2° / 20 Hz-20 kHz Jitter, jitter sensitivity and jitter suppression · AES3 (AES3-2003) compliant Latency · · 3.4 mS Analog-to-PC or PC-to-Analog (Windows 7 / 64 bits) 3.8 mS Analog-to-MAC or MAC-to-Analog (Mac OS X 10.6.8) External Connectors CANCUN 222-Mic CANCUN 442-Mic 25 pin Sub-D (compatible with DB25 YAMAHA DIGITAL) XLR female for analog input 1 44 pin Sub-D HD XLR female for analog input 1 6.35mm jack 6.
Management Windows XP: DirectSound, ASIO, Digigram np SDK through Virtual PCX Windows Seven; DirectSound, ASIO, Core Audio, WASAPI, Digigram np SDK via Virtual PCX Mac OS X: CoreAudio Linux: Alsa* * Functionality not implemented yet. This will be available by software upgrade.
CANCUN 222-Mic schematic diagram 26
CANCUN 442-Mic schematic diagram 27
CANCUN 222-Mic CABLE CANCUN 222-Mic cable schematic CANCUN 222-Mic Wiring diagram CANCUN 222-Mic cable pinout 28
Pin# Signal Pin# Signal 1 ANALOG IN1 Left + 14 ANALOG IN1 Left - 2 ANALOG IN2 Right + 15 ANALOG IN2 Right - 3 Not connected 16 Not connected 4 AES IN1 + (AES SYNCHRO) 17 AES IN1 - (AES SYNCHRO) 5 ANALOG OUT1 Left + 18 ANALOG OUT1 Left - 6 ANALOG OUT2 Right + 19 ANALOG OUT2 Right - 7 Not connected 20 Not connected 8 AES/EBU OUT + 21 AES/EBU OUT - 9 Not connected 22 GND 10 GND 23 GND 11 Not connected 24 GND 12 GND 25 GND 13 GND 29
CANCUN 442-Mic CABLE CANCUN 442-Mic cable schematic 30
CANCUN 442-Mic Wiring diagram 31
CACUN 442-Mic cable pinout Pin# Signal Pin# Signal 1 ANALOG IN4 Right + 23 GND 2 ANALOG IN4 Right - 24 GND 3 ANALOG IN3 Left + 25 Not connected 4 ANALOG IN3 Left - 26 GND 5 ANALOG OUT1 Left + 27 GND 6 ANALOG OUT1 Right + 28 GND 7 ANALOG OUT3 Left + 29 GND 8 ANALOG OUT3 Left - 30 AES/EBU IN2 + 9 Not connected 31 ANALOG IN1 Left + 10 AES/EBU IN1 + (AES Synchro) 32 ANALOG IN1 Left - 11 AES/EBU IN1 - (AES Synchro) 33 ANALOG IN2 Right + 12 GND 34 ANALOG IN2 Righ
