ConnectCore 6 Plus Hardware Reference Manual
Revision history—90002278 Revision Date Description G August 2020 Revised MCA pinout comments, added MCA functionality note. H October 2021 Added safety instructions and UKCA labeling requirements. J December 2021 Listed new Bluetooth IDs. K January 2022 Add Japan certifications. L July 2022 Add additional FCC-approved antennas. Trademarks and copyright Digi, Digi International, and the Digi logo are trademarks or registered trademarks in the United States and other countries worldwide.
Contact Digi technical support: Digi offers multiple technical support plans and service packages. Contact us at +1 952.912.3444 or visit us at www.digi.com/support. Feedback To provide feedback on this document, email your comments to techcomm@digi.com Include the document title and part number (ConnectCore 6 Plus Hardware Reference Manual, 90002278 L) in the subject line of your email.
Contents About the ConnectCore 6 Plus Features and functionality Safety instructions Block diagram Power supply architecture Bootstrap Wireless interfaces WLAN IEEE 802.
SMT pick and place SMT process parameter reference Reflow profile 91 91 91 Regulatory information and certifications United States FCC Labeling requirements Maximum power and frequency specifications (FCC) FCC notices FCC-approved antennas RF exposure Canada (ISED) Maximum power and frequency specifications Labeling requirements Transmitters with detachable antennas Europe ETSI and UKCA Maximum power and frequency specifications (Europe ETSI) CE and UKCA OEM labeling requirements Declarations of Conformit
About the ConnectCore 6 Plus The ConnectCore 6 Plus is an integrated platform solution with processor speed up to 1.2 GHz and pre-certified dual-band Wi-Fi (802.11a/b/g/n/ac) with Bluetooth 5.0 dual mode connectivity. Cloud Connector integration, as part of the Digi Linux and Android software platform support, offers secure remote management and web services capabilities through Digi Remote Manager.
About the ConnectCore 6 Plus Features and functionality Note To serve our customers most effectively, Digi International Inc. is consolidating its cloud services, Digi Device Cloud and Digi Remote Manager®, under the Remote Manager name. This phased process does not affect device functionality or the functionality of the web services and other features. However, you will find instances of both Device Cloud and Digi Remote Manager in some documentation, firmware, and user interfaces.
About the ConnectCore 6 Plus n Safety instructions Support of i.MX6QP typical interfaces: l 16/32-bit data/address bus l SATA II, 3.0 Gbps (24-bit parallel bus, LVDS, HDMI, MIPI/DSI) l Display support o HDMI o 24-bit parallel bus o Dual LVDS o MIPI/DSI l 2x camera (20-bit parallel bus, MIPI/CSI) l MMC/SD/SDIO l 1x USB OTG with integrated PHY l 3x USB Host l PCI Express Gen 2.
About the ConnectCore 6 Plus n Block diagram The end user must be told how to remove power from the ConnectCore 6 Plus module or to locate the antennas 20 cm from humans or animals. Block diagram The figure below shows the block diagram of the NXP i.MX6QP application processor. Power supply architecture The ConnectCore 6 Plus provides a primary 5 V power supply input.
About the ConnectCore 6 Plus Power supply architecture l VLDO4 l VLDO6 l VLDO8 l VDD_SD2 l VDD_WLAN_SD1 Signal name PMIC regulator Output voltage Output accuracy Maximum current Dropout voltage (MAX) VGEN_ 3V3 BUCKPERI 3.3 V +/-3% 1500 mA - Turn on time (MAX) Turn off time (MAX) Quiescent current in OFF mode (TYP) 1 µA 1.
About the ConnectCore 6 Plus Power supply architecture Signal name Turn on time (MAX) Turn off time (MAX) VLDO8 300 µs 1 ms VDD_SD2 200 µs 1 ms VDD_WLAN_SD1 200 µs 1 ms Note For information about using the LDO options, contact Digi. VLDO3 is used for supplying MCA processor on the module. The power management IC located on the module is responsible for generating all required i.MX6QP processor supply voltages. The following i.
About the ConnectCore 6 Plus Power supply architecture Power domain Min Typical Max NVCC_RGMII in HSIC 1.2 V mode 1.15 V - 1.30 V NVCC_RGMII in RGMII 1.5 V mode 1.43 V - 1.58 V NVCC_RGMII in RGMII 1.8 V mode 1.70 V - 1.90 V NVCC_RGMII in RGMII 2.5 V mode 2.25 V - 2.625 V As shown in the table above, the supplies have a wide operating range.
About the ConnectCore 6 Plus Bootstrap The following diagram outlines the ConnectCore 6 Plus power supply. Bootstrap The ConnectCore 6 Plus module can be configured to boot from different devices and interfaces determined by the boot ROM.
About the ConnectCore 6 Plus Bootstrap n BOOT_MODE register, which selects the boot mode of the processor n eFUSEs and/or GPIOs, which determine the boot configuration Four boot modes are available on the i.MX6QP processor. Selection between them is done through BOOT_MODE[1:0] bits.
About the ConnectCore 6 Plus Wireless interfaces Internal Boot Internal boot is the recommended boot mode for development purposes. When this boot mode is selected, the selection and configuration of the booting process is done through the same registers used when booting from fuses. However, this time the values of some registers are overridden using multiple GPIOs—which are latched during power-up.
About the ConnectCore 6 Plus Wireless interfaces WLAN IEEE 802.11a/b/g/n/ac The 2.4 GHz band on the ConnectCore 6 Plus module supports 20/40 MHz bandwidths, and the 5 GHz band supports 20/40/80 MHz bandwidths. The following sections specify the performance of the WLAN IEEE 802.11a/b/g/n/ac interface on the ConnectCore 6 Plus module. Modulation and data rates The following tables list modulation values for ConnectCore 6 Plus module supports the following WLAN standards.
About the ConnectCore 6 Plus Wireless interfaces Mode Modulation & coding Rate 802.11ac BPSK-1/2 MCS0 QPSK-1/2 MCS1 QPSK-3/4 MCS2 16QAM-1/2 MCS3 16QAM-3/4 MCS4 64QAM-2/3 MCS5 64QAM-3/4 MCS6 64QAM-5/6 MCS7 256QAM-3/4 MCS8 256QAM-5/6 MCS9 Data rate (Mbps) - Non Short Guard Interval (Non-SGI) Data rate (Mbps) 802.11b 802.
About the ConnectCore 6 Plus Wireless interfaces 802.11b Mode 5 GHz HT20 802.11ga 802.11n 6 7.2 72.2 7.2 72.2 15 150 15 150 200 32.5 325 433.3 54 HT40 802.11ac HT80 RF channels The ConnectCore 6 Plus module supports the following frequency bands. RF band Ch. BW Ch. spacing Channel number (Center freq. MHz) 2.
About the ConnectCore 6 Plus Wireless interfaces 2.4 GHz band channel # Center frequency (MHz) Europe (ETSI) North America (FCC) Japan 4 2427 ✔ ✔ ✔ 5 2432 ✔ ✔ ✔ 6 2437 ✔ ✔ ✔ 7 2442 ✔ ✔ ✔ 8 2447 ✔ ✔ ✔ 9 2452 ✔ ✔ ✔ 10 2457 ✔ ✔ ✔ 11 2462 ✔ ✔ ✔ 12 2467 ✔ No ✔ 13 2472 ✔ No ✔ 14 2484 No No 802.
About the ConnectCore 6 Plus Wireless interfaces 5 GHz band channel # Center frequency (MHz) EUROPE (ETSI) NORTH AMERICA (FCC) JAPAN 128 5640 DFS / TPC No access DFS / TPC 132 5660 DFS / TPC DFS DFS / TPC 136 5680 DFS / TPC DFS DFS / TPC 140 5700 DFS / TPC DFS DFS / TPC 149 5745 SRD ✔ No access 153 5765 SRD ✔ No access 157 5785 SRD ✔ No access 161 5805 SRD ✔ No access 165 5825 SRD ✔ No access Note DFS = Dynamic Frequency Selection TPC = Transmit Power Control
About the ConnectCore 6 Plus MCA hardware RF Band Channel BW Standard Output power (dBm) 2.4 GHz 5 GHz 20 MHz 802.11b 18 (1 Mbps) - 18 (11 Mbps) 20 MHz 802.11g 18 (6 Mbps) - 16 (54 Mbps) 20 MHz 802.11n 18 (MCS0) - 15 (MCS7) 40 MHz 802.11n 17 (MCS0) - 15 (MCS7) 40 MHz 802.11ac 17 (MCS0) - 13 (MCS9) 20 MHz 802.11a 13 (6 Mbps) - 11 (54 Mbps) 20 MHz 802.11n 13 (MCS0) - 10 (MCS7) 40 MHz 802.11n 12 (MCS0) - 9 (MCS7) 40 MHz 802.11ac 12 (MCS0) - 5 (MCS9) 80 MHz 802.
About the ConnectCore 6 Plus n MKL15Z64VFT4 n MKL24Z32VFT4 n MKL24Z64VFT4 n MKL25Z128VFT4 n MKL25Z32VFT4 n MKL25Z64VFT4 n MKL26Z128VFT4 n MKL26Z64VFT4 n MKL26Z32VFT4 n K10P48M50SF0 n K20P48M50SF0 MCA hardware By default, NXP MKL14Z32VFT4 is populated on the module variants supporting the MCA unit.
About the ConnectCore 6 Plus MCA hardware MCA pinout The table below contains the pinouts for the MCA unit on the ConnectCore 6 Plus module. Note The pinout information assumes you are using the NXP MKL14Z32VFT4 microcontroller. Using a different Kinetis microcontroller may change the functions available on the MCA pins.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module 7 ADC0_SE0 PTE20 TPM1_CH0 UART0_TX - T23 MCA_IO0 8 ADC0_SE4a PTE21 TPM1_CH1 UART0_RX - P23 MCA_IO1 9 VDDA - LDO3_MCA MCA power supply. A 100 nF capacitor connected to GND is placed close to this pin on theConnectCore 6 Plus SOM. 10 VREFH AC10 MCA_VREFH A 100 nF capacitor connected to GND is placed close to this pin on theConnectCore 6 Plus SOM.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name PTE24 TPM0_CH0 I2C0_SCL - Usage on module PMIC, which is the clock input of the MCA processor.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module SWD_DIO 21 PTA4 I2C1_SDA TPM0_CH1 NMI_b AA21 MCA_IO26 22 VDD - LDO3_MCA MCA power supply 1x 100 nF + 1x1 µF capacitors connected to GND are placed close to this pin on ConnectCore 6 Plus SOM. 23 VSS - GND MCA ground 24 EXTAL0 PTA18 UART1_RX TPM_CLKIN0 - - PMIC_STBY_REQ Connected on ConnectCore 6 Plus SOM to i.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module TPM1_CH1 29 ADC0_SE12 PTB2 I2C0_SCL TPM2_CH0 - - INTERNAL_I2C_ SCL Connected directly to PMIC I2C_SCL signal and to i.MX6QP processor I2C2_SCL/KEY_COL3 signal (ball U5) over N-channel MOSFET. 30 ADC0_SE13 PTB3 I2C0_SDA TPM2_CH1 - - INTERNAL_I2C_ SDA Connected directly to PMIC I2C_SDA signal and to i.MX6QP processor I2C2_SDA/KEY_ROW3 signal (ball T7) over N-channel MOSFET.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module This MCA pin is connected to 32K output of the PMIC. For KL14, KL15, KL24 and KL25 this pin can be configured as RTC_CLKIN signal.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module P10 SPI0_MOSI EXTRG_IN SPI0_MISO 40 CMP0_IN1 PTC7 SPI0_MISO SPI0_MOSI - R20 MCA_IO19 41 PTD0 SPI0_PCS0 TPM0_CH0 - A6 CSI0_ DAT11/ECSPI2_ SS0 Connected to i.MX6QP processor signal CSI0_ DAT11 (ball M3) and to LGA pad A6. This pin can be configured as a SPI chip select shared between MCA and i.MX6QP processor.
About the ConnectCore 6 Plus MCA Pin Nr MCA hardware ConnectCore 6 Plus Signal name Pad Nr Signal name Usage on module 45 PTD4/LLWU_ P14 SPI1_PCS0 UART2_RX TPM0_CH4 - R21 MCA_IO16 46 ADC0_SE6b PTD5 SPI1_SCK UART2_TX TPM0_CH5 - T21 MCA_IO22 47 ADC0_SE7b PTD6/LLWU_ P15 SPI1_MOSI UART0_RX SPI1_MISO - T24 MCA_IO3 48 PTD7 SPI1_MISO UART0_TX SPI1_MOSI - AA20 MCA_IO21 The i.MX6QP pads listed above are connected to ConnectCore 6 Plus pads.
About the ConnectCore 6 Plus MCA hardware Shared I2C bus The screenshot below shows how the I2C bus (I2C2) is used on ConnectCore 6 Plus module. The bus is shared between i.MX6QP processor and the PMIC, the MCA, and the cryptochip. The usage of Nchannel MOSFET ensures the bus is fully isolated and allows the i.MX6QP processor to be shut off while MCA and PMIC are powered.
About the ConnectCore 6 Plus MCA hardware Shared SPI bus In addition to an I2C interface, i.MX6QP shares an SPI bus with the MCA microcontroller. The table below shows this connection: SPI function i.
About the ConnectCore 6 Plus CryptoAuthentication device CryptoAuthentication device The ConnectCore 6 Plus includes an Atmel CryptoAuthentication Device. This is a highly secure cryptographic co-processor with secure hardware-based key storage. It includes the following features: n Performs high-speed public key (PKI) algorithms (ECDSA and ECDH). n NIST standard P256 elliptic curve support. n SHA-256 hash algorithm with HMAC option. n 256-bit key length. n Storage for up to 16 keys.
About the ConnectCore 6 Plus Module pinout Module pinout The module has an LGA pad structure based on 400 pads. See the following diagram for the general layout, which shows the top view of the module pinouts. The following table provides the pinout of the ConnectCore 6 Plus module. Additional timing and electrical information can be found in either the NXP i.MX6QP processor datasheet (www.nxp.com) or the Dialog DA9063 product datasheet (www.dialog-semiconductor.com).
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing A5 CSI0_MCLK ALT0: IPU1_CSI0_HSYNC NVCC_CSI ALT1: ALT2: ALT3: CCM_CLKO1 ALT4: ALT5: GPIO5_IO19 ALT6: ALT7: ARM_TRACE_CTL A6 CSI0_DAT11 ALT0: IPU1_CSI0_ DATA11 ALT1: AUD3_RXFS ALT2: ECSPI2_SS0 ALT3: UART1_RX_DATA ALT4: ALT5: GPIO5_IO29 ALT6: ALT7: ARM_TRACE08 NVCC_CSI A7 CSI0_DAT17 ALT0: IPU1_CSI0_ DATA17 ALT1: EIM_DATA13 ALT2: ALT3: UART4_CTS_B ALT4: ALT5: GPIO6_IO03 ALT6: ALT7: ARM_TRACE14 NVCC_CSI A8 GND - - A9 H
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group B4 LVDS0_TX2_P - NVCC_LVDS_2P5 B5 GND - - B6 CSI0_DAT14 ALT0: IPU1_CSI0_ DATA14 ALT1: EIM_DATA10 ALT2: ALT3: UART5_TX_DATA ALT4: ALT5: GPIO6_IO00 ALT6: ALT7: ARM_TRACE11 NVCC_CSI B7 CSI0_DAT4 ALT0: IPU1_CSI0_ DATA04 ALT1: EIM_DATA02 ALT2: ECSPI1_SCLK ALT3: KEY_COL5 ALT4: AUD3_TXC ALT5: GPIO5_IO22 ALT6: ALT7: ARM_TRACE01 NVCC_CSI B8 HDMI_D1_N - HDMI_VPH B9 HDMI_D0_P - HDMI_VPH B10 DSI_D0_P -
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments Connected to MCA processor and PMIC. Not recommended as main I2C port. 4.7K pull-up on module.
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group C12 CSI_D2_P - NVCC_MIPI C13 GND - - C14 GND - - C15 GND - - C16 USB_H1_DN - VDD_USB_CAP C17 TAMPER - VDD_SNVS_IN C18 PCM_IN - VGEN_3V3 C19 MLB_SP - VDD_HIGH_CAP C20 MLB_SN - VDD_HIGH_CAP C21 SD3_DAT7 ALT0: SD3_DATA7 ALT1: UART1_TX_DATA ALT2: ALT3: ALT4: ALT5: GPIO6_IO17 ALT6: ALT7: VGEN_3V3 C22 SD3_DAT4/ BT_UART_RXD ALT0: SD3_DATA4 ALT1: UART2_RX_DATA ALT2: ALT3: ALT4: ALT5:
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group D4 GND - - D5 CSI0_DAT9 ALT0: IPU1_CSI0_ DATA09 ALT1: EIM_DATA07 ALT2: ECSPI2_MOSI ALT3: KEY_ROW7 ALT4: I2C1_SCL ALT5: GPIO5_IO27 ALT6: ALT7: ARM_TRACE06 NVCC_CSI Connected to the on-module MCA microcontroller.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: ALT4: ALT5: GPIO7_IO05 ALT6: ALT7: D22 SD3_RST ALT0: SD3_RESET ALT1: UART3_RTS_B ALT2: ALT3: ALT4: ALT5: GPIO7_IO08 ALT6: ALT7: VGEN_3V3 D23 SD3_DAT5/ BT_UART_TXD ALT0: SD3_DATA5 ALT1: UART2_TX_DATA ALT2: ALT3: ALT4: ALT5: GPIO7_IO00 ALT6: ALT7: VGEN_3V3 E1 LVDS1_CLK_N - NVCC_LVDS_2P5 E2 KEY_ROW0 ALT0: ECSPI1_MOSI ALT1: ENET_TX_DATA3 ALT2: AUD5_TXD ALT3: KEY_ROW0 ALT4: UART4_RX_DATA ALT5:
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT6: ALT7: ARM_TRACE_CLK E6 CSI0_DAT15 ALT0: IPU1_CSI0_ DATA15 ALT1: EIM_DATA11 ALT2: ALT3: UART5_RX_DATA ALT4: ALT5: GPIO6_IO01 ALT6: ALT7: ARM_TRACE12 NVCC_CSI E7 GND - - E8 HDMI_CLK_N - HDMI_VPH E9 DSI_D1_N - NVCC_MIPI E10 DSI_CLK0_N - NVCC_MIPI E11 CSI_D3_N - NVCC_MIPI E12 PCM_SYNC - VGEN_3V3 E13 PCM_CLK - VGEN_3V3 E14 JTAG_TDO - VGEN_3V3 E15 Reserved - - E16 GND
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments during reset. Can be used to synchronize external circuitry reset.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group ALT2: HDMI_TX_DDC_ SDA ALT3: KEY_ROW3 ALT4: I2C2_SDA ALT5: GPIO4_IO13 ALT6: SD1_VSELECT ALT7: Not recommended as main I2C port. 4.7K pull-up on module.
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group F18 MLB_CN - - F19 GND - - F20 SD3_DAT0 ALT0: SD3_DATA0 ALT1: UART1_CTS_B ALT2: FLEXCAN2_TX ALT3: ALT4: ALT5: GPIO7_IO04 ALT6: ALT7: VGEN_3V3 F21 NANDF_CS0 ALT0: NAND_CE0_B ALT1: ALT2: ALT3: ALT4: ALT5: GPIO6_IO11 ALT6: ALT7: VGEN_3V3 F22 #NANDF_WP ALT0: NAND_WP_B ALT1: IPU2_SISG5 ALT2: ALT3: ALT4: ALT5: GPIO6_IO09 ALT6: ALT7: VGEN_3V3 F23 NANDF_CS3 ALT0: NAND_CE3_B ALT1: IPU1_SISG1 ALT2: ESAI_TX
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT2: KEY_COL5 ALT3: ASRC_EXT_CLK ALT4: EPIT1_OUT ALT5: GPIO1_IO00 ALT6: USB_H1_PWR ALT7: SNVS_VIO_5 G3 GPIO_2 ALT0: ESAI_TX_FS ALT1: ALT2: KEY_ROW6 ALT3: ALT4: ALT5: GPIO1_IO02 ALT6: SD2_WP ALT7: MLB_DATA VGEN_3V3 G4 GND - - G5 CSI0_PIXCLK ALT0: IPU1_CSI0_ PIXCLK ALT1: ALT2: ALT3: ALT4: ALT5: GPIO5_IO18 ALT6: ALT7: ARM_EVENTO NVCC_CSI G6 CSI0_DAT19 ALT0: IPU1_CSI0_ DATA19 ALT1: EIM_DATA15 ALT2
About the ConnectCore 6 Plus Module pinout LGA pad Pad name G15 #USB_OTG_CHD - VDD_USB_CAP G16 USB_OTG_DN - VDD_USB_CAP G17 USB_OTG_DP - VDD_USB_CAP G18 GND - - G19 SATA_RX_N - SATA_VPH G20 VGEN_3V3 - - G21 NANDF_D2 ALT0: NAND_DATA02 ALT1: SD1_DATA6 ALT2: ALT3: ALT4: ALT5: GPIO2_IO02 ALT6: ALT7: VGEN_3V3 G22 NANDF_D6 ALT0: NAND_DATA06 ALT1: SD2_DATA6 ALT2: ALT3: ALT4: ALT5: GPIO2_IO06 ALT6: ALT7: VGEN_3V3 G23 NANDF_D3 ALT0: NAND_DATA03 ALT1: SD1_DATA7 ALT2: ALT3: ALT4: A
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT5: GPIO4_IO11 ALT6: HDMI_TX_CEC_ LINE ALT7: H3 GPIO_9 ALT0: ESAI_RX_FS ALT1: WDOG1_B ALT2: KEY_COL6 ALT3: CCM_REF_EN_B ALT4: PWM1_OUT ALT5: GPIO1_IO09 ALT6: SD1_WP ALT7: VGEN_3V3 H4 LVDS0_TX0_P - NVCC_LVDS_2P5 H5 GND - - H6 CSI0_DAT16 ALT0: IPU1_CSI0_ DATA16 ALT1: EIM_DATA12 ALT2: ALT3: UART4_RTS_B ALT4: ALT5: GPIO6_IO02 ALT6: ALT7: ARM_TRACE13 NVCC_CSI H19 SATA_RX_P - SATA_VPH H20 GN
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT4: ALT5: GPIO2_IO07 ALT6: ALT7: H24 NANDF_CS2 ALT0: NAND_CE2_B ALT1: IPU1_SISG0 ALT2: ESAI_TX0 ALT3: EIM_CRE ALT4: CCM_CLKO2 ALT5: GPIO6_IO15 ALT6: IPU2_SISG0 ALT7: VGEN_3V3 J1 LVDS1_TX0_P - NVCC_LVDS_2P5 J2 KEY_COL0 ALT0: ECSPI1_SCLK ALT1: ENET_RX_DATA3 ALT2: AUD5_TXC ALT3: KEY_COL0 ALT4: UART4_TX_DATA ALT5: GPIO4_IO06 ALT6: DCIC1_OUT ALT7: VGEN_3V3 J3 GPIO_6 ALT0: ESAI_TX_CLK ALT1: ALT2: I
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments B_DEB ALT7: J22 SD1_DAT1 ALT0: SD1_DATA1 ALT1: ECSPI5_SS0 ALT2: PWM3_OUT ALT3: GPT_CAPTURE2 ALT4: ALT5: GPIO1_IO17 ALT6: ALT7: VDD_WLAN_SD1 Signal only available externally in nonwireless variants of the SOM.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group DATA10 ALT1: AUD3_RXC ALT2: ECSPI2_MISO ALT3: UART1_TX_DATA ALT4: ALT5: GPIO5_IO28 ALT6: ALT7: ARM_TRACE07 on-module MCA microcontroller.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT5: GPIO4_IO14 ALT6: ALT7: L3 GPIO_4 ALT0: ESAI_TX_HF_CLK ALT1: ALT2: KEY_COL7 ALT3: ALT4: ALT5: GPIO1_IO04 ALT6: SD2_CD_B ALT7: VGEN_3V3 L4 LVDS0_CLK_P - NVCC_LVDS_2P5 L5 CSI0_DAT12 ALT0: IPU1_CSI0_ DATA12 ALT1: EIM_DATA08 ALT2: ALT3: UART4_TX_DATA ALT4: ALT5: GPIO5_IO30 ALT6: ALT7: ARM_TRACE09 NVCC_CSI L20 SD1_DAT3 ALT0: SD1_DATA3 ALT1: ECSPI5_SS2 ALT2: GPT_COMPARE3 ALT3: PWM1_OUT ALT4: WDO
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT7: SWD_CLK L24 NANDF_D5 ALT0: NAND_DATA05 ALT1: SD2_DATA5 ALT2: ALT3: ALT4: ALT5: GPIO2_IO05 ALT6: ALT7: VGEN_3V3 M1 LVDS1_TX1_N - NVCC_LVDS_2P5 M2 GPIO_19 ALT0: KEY_COL5 ALT1: ENET_1588_ EVENT0_OUT ALT2: SPDIF_OUT ALT3: CCM_CLKO1 ALT4: ECSPI1_RDY ALT5: GPIO4_IO05 ALT6: ENET_TX_ER ALT7: NVCC_GPIO (VGEN_3V3) M3 GPIO_16 ALT0: ESAI_TX3_RX2 ALT1: ENET_1588_ EVENT2_IN ALT2: ENET_REF_CLK ALT3: SD1
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group Comments M21 MCA_IO12 ALT0: ALT1: PTC5/LLWU_P9 ALT2: SPI0_SCK ALT3: LPTMR0_ALT2 ALT4: ALT5: ALT6: CMP0_OUT ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT6: ALT7: N21 MCA_IO13 ALT0: CMP0_IN0 ALT1: PTC6/LLWU_P10 ALT2: SPI0_MOSI ALT3: EXTRG_IN ALT4: ALT5: SPI0_MISO ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA. N22 MCA_IO7 ALT0: ALT1: PTB16 ALT2: SPI1_MOSI ALT3: UART0_RX ALT4: TPM_CLKIN0 ALT5: SPI1_MISO ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: FLEXCAN1_TX ALT4: UART2_TX_DATA ALT5: GPIO1_IO07 ALT6: SPDIF_LOCK ALT7: USB_OTG_HOST_ MODE P4 LVDS0_TX3_P - NVCC_LVDS_2P5 P5 NVCC_CSI - - P20 MCA_IO/USB0_ N ALT0: ADC0_SE5a ALT1: PTE17 ALT2: SPI0_SCK ALT3: UART2_RX ALT4: TPM_CLKIN1 ALT5: ALT6: LPTMR0_ALT3 ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT6: DCIC2_OUT ALT7: R1 LVDS1_TX2_P - NVCC_LVDS_2P5 R2 ENET_RX_ER ALT0: USB_OTG_ID ALT1: ENET_RX_ER ALT2: ESAI_RX_HF_CLK ALT3: SPDIF_IN ALT4: ENET_1588_ EVENT2_OUT ALT5: GPIO1_IO24 ALT6: ALT7: NVCC_ENET R3 GPIO_5 ALT0: ESAI_TX2_RX3 ALT1: ALT2: KEY_ROW7 ALT3: CCM_CLKO1 ALT4: ALT5: GPIO1_IO05 ALT6: I2C3_SCL ALT7: ARM_EVENTI NVCC_GPIO (VGEN_3V3) R4 LVDS0_TX3_N - NVCC_LVDS_2P5 R5 NVCC_RGMII -
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group Comments R23 MCA_IO2 ALT0: ADC0_SE8 ALT1: PTB0/LLWU_P5 ALT2: I2C0_SCL ALT3: TPM1_CH0 ALT4: ALT5: ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group Comments T22 MCA_IO10 ALT0: ALT1: PTC3/LLWU_P7 ALT2: ALT3: UART1_RX ALT4: TPM0_CH2 ALT5: CLKOUT ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA. T23 MCA_IO0 ALT0: ADC0_SE0 ALT1: PTE20 ALT2: ALT3: TPM1_CH0 ALT4: UART0_TX ALT5: ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: ALT4: ALT5: GPIO6_IO20 ALT6: ALT7: U6 DISP0_DAT21 ALT0: IPU1_DISP0_ DATA21 ALT1: IPU2_DISP0_ DATA21 ALT2: ECSPI1_MOSI ALT3: AUD4_TXD ALT4: ALT5: GPIO5_IO15 ALT6: ALT7: NVCC_LCD U19 EIM_DA3 ALT0: EIM_DA03 ALT1: IPU1_DISP1_ DATA06 ALT2: IPU2_CSI1_ DATA06 ALT3: ALT4: ALT5: GPIO3_IO03 ALT6: ALT7: SRC_BOOT_ CFG03 NVCC_EIM U20 EIM_DA0 ALT0: EIM_AD00 ALT1: IPU1_DISP1_ DATA09 ALT2: IPU2_CSI1_ DATA09
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group ALT1: PTC4/LLWU_P8 ALT2: SPI0_PCS0 ALT3: UART1_TX ALT4: TPM0_CH3 ALT5: ALT6: ALT7: - Comments in variants carrying the MCA. U23 EIM_DA6 ALT0: EIM_AD06 ALT1: IPU1_DISP1_ DATA03 ALT2: IPU2_CSI1_ DATA03 ALT3: ALT4: ALT5: GPIO3_IO06 ALT6: ALT7: SRC_BOOT_ CFG06 NVCC_EIM 10K pull-up to NVCC_EIM on module.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT1: RGMII_TD1 ALT2: ALT3: ALT4: ALT5: GPIO6_IO21 ALT6: ALT7: V6 DISP0_DAT16 ALT0: IPU1_DISP0_ DATA16 ALT1: IPU2_DISP0_ DATA16 ALT2: ECSPI2_MOSI ALT3: AUD5_TXC ALT4: SDMA_EXT_ EVENT0 ALT5: GPIO5_IO10 ALT6: ALT7: NVCC_LCD V7 DISP0_DAT22 ALT0: IPU1_DISP0_ DATA22 ALT1: IPU2_DISP0_ DATA22 ALT2: ECSPI1_MISO ALT3: AUD4_TXFS ALT4: ALT5: GPIO5_IO16 ALT6: ALT7: NVCC_LCD V8 DI0_PIN3 ALT0: IPU1_DI0_PIN03 ALT
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT2: AUD6_TXC ALT3: ALT4: ALT5: GPIO4_IO17 ALT6: ALT7: V11 VSYS - - V12 PMIC_GPIO11 - - PMIC V13 PMIC_GPIO15 - - PMIC V14 CHG_WAKE - - PMIC V15 EIM_OE ALT0: EIM_OE ALT1: IPU1_DI1_PIN07 ALT2: ECSPI2_MISO ALT3: ALT4: ALT5: GPIO2_IO25 ALT6: ALT7: NVCC_EIM V16 EIM_EB1 ALT0: EIM_EB1 ALT1: IPU1_DISP1_ DATA10 ALT2: IPU2_CSI1_ DATA10 ALT3: ALT4: ALT5: GPIO2_IO29 ALT6: ALT7: SRC_BOOT_ CFG28
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT7: SRC_BOOT_ CFG11 V19 EIM_DA9 ALT0: EIM_DA9 ALT1: IPU1_DISP1_ DATA00 ALT2: IPU2_CSI1_ DATA00 ALT3: ALT4: ALT5: GPIO3_IO09 ALT6: ALT7: SRC_BOOT_ CFG09 NVCC_EIM V20 EIM_DA13 ALT0: EIM_DA13 ALT1: IPU1_DI1_D0_CS ALT2: ALT3: ALT4: ALT5: GPIO3_IO13 ALT6: ALT7: SRC_BOOT_ CFG13 NVCC_EIM V21 EIM_DA10 ALT0: EIM_DA10 NVCC_EIM ALT1: IPU1_DI1_PIN15 ALT2: IPU2_CSI1_DATA_ EN ALT3: ALT4: ALT5: GPIO3_IO10 ALT6:
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: ALT4: ALT5: GPIO3_IO02 ALT6: ALT7: SRC_BOOT_ CFG02 W1 GND - - W2 GND - - W3 ENET_MDC ALT0: MLB_DATA ALT1: ENET_MDC ALT2: ESAI_TX5_RX0 ALT3: ALT4: ENET_1588_ EVENT1_IN ALT5: GPIO1_IO31 ALT6: ALT7: NVCC_ENET W4 RGMII_TX_CTL ALT0: USB_H2_STROBE ALT1: RGMII_TX_CTL ALT2: ALT3: ALT4: ALT5: GPIO6_IO26 ALT6: ALT7: ENET_REF_CLK NVCC_RGMII W5 GND - - W6 DISP0_DAT20 ALT0: IPU1_DISP0_ DATA20
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group W8 DISP0_DAT13 ALT0: IPU1_DISP0_ DATA13 ALT1: IPU2_DISP0_ DATA13 ALT2: ALT3: AUD5_RXFS ALT4: ALT5: GPIO5_IO07 ALT6: ALT7: NVCC_LCD W9 GND - - W10 DI0_PIN2 ALT0: IPU1_DI0_PIN02 ALT1: IPU2_DI0_PIN02 ALT2: AUD6_TXD ALT3: ALT4: ALT5: GPIO4_IO18 ALT6: ALT7: NVCC_LCD W11 VSYS - - W12 VSYS - - W13 PMIC_PWR_EN - - W14 GND - - W15 EIM_RW ALT0: EIM_RW ALT1: IPU1_DI1_PIN08 ALT2: ECSPI2_SS0 ALT3: ALT
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: IPU1_DI1_PIN12 ALT4: IPU1_DI0_D1_CS ALT5: GPIO5_IO02 ALT6: HDMI_TX_CEC_ LINE ALT7: W19 EIM_D20 ALT0: EIM_DATA20 ALT1: ECSPI4_SS0 ALT2: IPU1_DI0_PIN16 ALT3: IPU2_CSI1_ DATA15 ALT4: UART1_RTS_B ALT5: GPIO3_IO20 ALT6: EPIT2_OUT ALT7: NVCC_EIM W20 EIM_D24 ALT0: EIM_DATA24 ALT1: ECSPI4_SS2 ALT2: UART3_TX_DATA ALT3: ECSPI1_SS2 ALT4: ECSPI2_SS2 ALT5: GPIO3_IO24 ALT6: AUD5_RXFS ALT7: UART1_DTR_B NVCC_EI
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments 10K pull-down on module.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: ALT4: ALT5: GPIO6_IO22 ALT6: ALT7: Y6 DISP0_DAT19 ALT0: IPU1_DISP0_ DATA19 ALT1: IPU2_DISP0_ DATA19 ALT2: ECSPI2_SCLK ALT3: AUD5_RXD ALT4: AUD4_RXC ALT5: GPIO5_IO13 ALT6: ALT7: EIM_CS3 NVCC_LCD Y7 DISP0_DAT11 ALT0: IPU1_DISP0_ DATA11 ALT1: IPU2_DISP0_ DATA11 ALT2: ALT3: ALT4: ALT5: GPIO5_IO05 ALT6: ALT7: NVCC_LCD Y8 DISP0_DAT10 ALT0: IPU1_DISP0_ DATA10 ALT1: IPU2_DISP0_ DATA10 ALT2: ALT3: ALT
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT3: ALT4: CCM_PMIC_ READY ALT5: GPIO2_IO28 ALT6: ALT7: SRC_BOOT_ CFG27 Y15 EIM_D30 ALT0: EIM_DATA30 ALT1: IPU1_DISP1_ DATA21 ALT2: IPU1_DI0_PIN11 ALT3: IPU1_CSI0_ DATA03 ALT4: UART3_CTS_B ALT5: GPIO3_IO30 ALT6: USB_H1_OC ALT7: NVCC_EIM Y16 EIM_D21 ALT0: EIM_DATA21 ALT1: ECSPI4_SCLK ALT2: IPU1_DI0_PIN17 ALT3: IPU2_CSI1_ DATA11 ALT4: USB_OTG_OC ALT5: GPIO3_IO21 ALT6: I2C1_SCL ALT7: SPDIF_IN NVCC_EIM
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT2: IPU1_DI1_PIN04 ALT3: ALT4: ALT5: GPIO3_IO15 ALT6: ALT7: SRC_BOOT_ CFG15 Y21 EIM_DA7 ALT0: EIM_DA7 ALT1: IPU1_DISP1_ DATA02 ALT2: IPU2_CSI1_ DATA02 ALT3: ALT4: ALT5: GPIO3_IO07 ALT6: ALT7: SRC_BOOT_ CFG07 NVCC_EIM 10K pull-down on module.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT1: ENET_RX_DATA1 ALT2: ESAI_TX_FS ALT3: ALT4: ENET_1588_ EVENT3_OUT ALT5: GPIO1_IO26 ALT6: ALT7: AA3 ENET_TX_EN ALT0: ALT1: ENET_TX_EN ALT2: ESAI_TX3_RX2 ALT3: ALT4: ALT5: GPIO1_IO28 ALT6: ALT7: NVCC_ENET AA4 RGMII_RD0 ALT0: HSI_RX_READY ALT1: RGMII_RD0 ALT2: ALT3: ALT4: ALT5: GPIO6_IO25 ALT6: ALT7: NVCC_RGMII AA5 RGMII_TD3 ALT0: HSI_RX_WAKE ALT1: RGMII_TD3 ALT2: ALT3: ALT4: ALT5: GPIO6_IO23 ALT
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT4: ALT5: GPIO5_IO06 ALT6: ALT7: AA8 DISP0_DAT8 ALT0: IPU1_DISP0_ DATA08 ALT1: IPU2_DISP0_ DATA08 ALT2: PWM1_OUT ALT3: WDOG1_B ALT4: ALT5: GPIO4_IO29 ALT6: ALT7: NVCC_LCD AA9 DISP0_DAT4 ALT0: IPU1_DISP0_ DATA04 ALT1: IPU2_DISP0_ DATA04 ALT2: ECSPI3_SS1 ALT3: ALT4: ALT5: GPIO4_IO25 ALT6: ALT7: NVCC_LCD AA10 VLDO6 - - AA11 VLDO2 - - AA12 VGEN_3V3 - - AA13 EIM_WAIT ALT0: EIM_WAIT ALT1: E
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments CFG23 AA15 EIM_D31 ALT0: EIM_DATA31 ALT1: IPU1_DISP1_ DATA20 ALT2: IPU1_DI0_PIN12 ALT3: IPU1_CSI0_ DATA02 ALT4: UART3_RTS_B ALT5: GPIO3_IO31 ALT6: USB_H1_PWR ALT7: NVCC_EIM AA16 GND - - AA17 EIM_D25 ALT0: EIM_DATA25 ALT1: ECSPI4_SS3 ALT2: UART3_RX_DATA ALT3: ECSPI1_SS3 ALT4: ECSPI2_SS3 ALT5: GPIO3_IO25 ALT6: AUD5_RXC ALT7: UART1_DSR_B NVCC_EIM AA18 EIM_EB3 ALT0: EIM_EB3 NVCC_EIM ALT1: ECSPI4_RD
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT7: AA21 MCA_IO26 ALT0: ALT1: PTA4 ALT2: I2C1_SDA ALT3: TPM0_CH1 ALT4: ALT5: ALT6: ALT7: NMI_b LDO3_MCA Signal only available in variants carrying the MCA. AA22 MCA_IO25 ALT0: ALT1: PTA1 ALT2: UART0_RX ALT3: TPM2_CH0 ALT4: ALT5: ALT6: ALT7: - LDO3_MCA Signal only available in variants carrying the MCA.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments DATA09 ALT1: IPU2_DISP0_ DATA09 ALT2: PWM2_OUT ALT3: WDOG2_B ALT4: ALT5: GPIO4_IO30 ALT6: ALT7: AB7 DISP0_DAT6 ALT0: IPU1_DISP0_ DATA06 ALT1: IPU2_DISP0_ DATA06 ALT2: ECSPI3_SS3 ALT3: AUD6_RXC ALT4: ALT5: GPIO4_IO27 ALT6: ALT7: NVCC_LCD AB8 DISP0_DAT3 ALT0: IPU1_DISP0_ DATA03 ALT1: IPU2_DISP0_ DATA03 ALT2: ECSPI3_SS0 ALT3: ALT4: ALT5: GPIO4_IO24 ALT6: ALT7: NVCC_LCD AB9 PMIC_GPIO7 - - AB10 GND
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT6: ALT7: AB14 PMIC_ADCIN1/ GPIO0 - - PMIC line. AB15 EIM_A18 ALT0: EIM_ADDR18 ALT1: IPU1_DISP1_ DATA13 ALT2: IPU2_CSI1_ DATA13 ALT3: ALT4: ALT5: GPIO2_IO20 ALT6: ALT7: SRC_BOOT_ CFG18 NVCC_EIM Make sure this line is not pulled-high during boot.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments FAULT AB21 GND - - AB22 #PMIC_OFF - - AC4 RGMII_RD2 ALT0: HSI_TX_DATA ALT1: RGMII_RD2 ALT2: ALT3: ALT4: ALT5: GPIO6_IO28 ALT6: ALT7: NVCC_RGMII AC5 RGMII_RD3 ALT0: HSI_TX_WAKE ALT1: RGMII_RD3 ALT2: ALT3: ALT4: ALT5: GPIO6_IO29 ALT6: ALT7: NVCC_RGMII AC6 DISP0_DAT14 ALT0: IPU1_DISP0_ DATA14 ALT1: IPU2_DISP0_ DATA14 ALT2: ALT3: AUD5_RXC ALT4: ALT5: GPIO5_IO08 ALT6: ALT7: NVCC_LCD AC7 DISP0
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT5: GPIO4_IO21 ALT6: ALT7: AC9 DISP0_DAT1 ALT0: IPU1_DISP0_ DATA01 ALT1: IPU2_DISP0_ DATA01 ALT2: ECSPI3_MOSI ALT3: ALT4: ALT5: GPIO4_IO22 ALT6: ALT7: NVCC_LCD AC10 MCA_VREFH VREFH - AC11 VDD_SD2 - - AC12 GND - - AC13 GND - - AC14 PMIC_ADCIN2/ GPIO1 - - AC15 EIM_CS1 ALT0: EIM_CS1 ALT1: IPU1_DI1_PIN06 ALT2: ECSPI2_MOSI ALT3: ALT4: ALT5: GPIO2_IO24 ALT6: ALT7: NVCC_EIM AC16 EIM_A
About the ConnectCore 6 Plus Module pinout LGA pad Pad name Multiplexing Power group AC17 EIM_A17 ALT0: EIM_ADDR17 ALT1: IPU1_DISP1_ DATA12 ALT2: IPU2_CSI1_ DATA12 ALT3: ALT4: ALT5: GPIO2_IO21 ALT6: ALT7: SRC_BOOT_ CFG17 NVCC_EIM AC18 GND - - AC19 EIM_A22 ALT0: EIM_ADDR22 ALT1: IPU1_DISP1_ DATA17 ALT2: IPU2_CSI1_ DATA17 ALT3: ALT4: ALT5: GPIO2_IO16 ALT6: ALT7: SRC_BOOT_ CFG22 NVCC_EIM AC20 EIM_D23 ALT0: EIM_DATA23 NVCC_EIM ALT1: IPU1_DI0_D0_CS ALT2: UART3_CTS_B ALT3: UART1_DCD_B ALT4: IP
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments 1x 100nF + 1x1µF capacitors connected to GND are placed close to this pin on the ConnectCore 6 Plus SOM.
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments ALT2: ECSPI3_MISO ALT3: ALT4: ALT5: GPIO4_IO23 ALT6: ALT7: AD10 VLDO4 - - AD11 VLDO8 - - AD12 PMIC_GP_FB3 - - PMIC AD13 PMIC_GP_FB1/ GPIO13 - - PMIC AD14 PMIC_ADCIN3/ GPIO2 - - PMIC AD15 EIM_A16 ALT0: EIM_ADDR16 ALT1: IPU1_DI1_DISP_ CLK ALT2: IPU2_CSI1_ PIXCLK ALT3: ALT4: ALT5: GPIO2_IO22 ALT6: ALT7: SRC_BOOT_ CFG16 NVCC_EIM AD16 EIM_A19 ALT0: EIM_ADDR19 ALT1: IPU1_DISP1_ DATA14
About the ConnectCore 6 Plus LGA pad Pad name Module pinout Multiplexing Power group Comments CFG24 AD18 EIM_D27 ALT0: EIM_DATA27 ALT1: IPU1_DI1_PIN13 ALT2: IPU1_CSI0_ DATA00 ALT3: IPU2_CSI1_ DATA13 ALT4: UART2_RX_DATA ALT5: GPIO3_IO27 ALT6: IPU1_SISG3 ALT7: IPU1_DISP1_ DATA23 NVCC_EIM AD19 EIM_D26 ALT0: EIM_DATA26 ALT1: IPU1_DI1_PIN11 ALT2: IPU1_CSI0_ DATA01 ALT3: IPU2_CSI1_ DATA14 ALT4: UART2_TX_DATA ALT5: GPIO3_IO26 ALT6: IPU1_SISG2 ALT7: IPU1_DISP1_ DATA22 NVCC_EIM AD20 EIM_D16 ALT0: EI
About the ConnectCore 6 Plus Signal use limitations Pad ConnectCore 6 ConnectCore 6 Plus C18 Unconnected PCM_IN PCM bus coming from the wireless transceiver used on the ConnectCore 6 Plus. D12 Unconnected PCM_OUT PCM bus coming from the wireless transceiver used on the ConnectCore 6 Plus. E12 Unconnected PCM_SYNC PCM bus coming from the wireless transceiver used on the ConnectCore 6 Plus. E13 Unconnected PCM_CLK PCM bus coming from the wireless transceiver used on the ConnectCore 6 Plus.
About the ConnectCore 6 Plus Signal use limitations processor and the i.MX6QP processor. The other signals are an SPI bus shared between thei.MX6QP and MCA processors. The usage and availability of these signals depends on the firmware running in the MCA processor. n ON/OFF (pad D18) signal is connected to PMIC and MCA. n #POR (pad E18) is connected to PMIC and i.MX6QP processor.
Specifications for the ConnectCore 6 Plus Electrical characteristics Power consumption Environmental specifications ConnectCore 6 Plus Hardware Reference Manual 86 86 87 85
Specifications for the ConnectCore 6 Plus Electrical characteristics Electrical characteristics Voltage supplies Parameter Min Typ Max Unit 5 V supply 4.2 5 5.5 V VCC_LICELL 2.0 3.0 TBD V LDO3_MCA 1.71 3.3 3.6 V Note No specific ESD protection components have been implemented on the ConnectCore 6 Plus module. ESD protection level on the module’s I/Os is the same as what is specified in the NXP datasheet. Any required ESD protection must be implemented on the carrier board.
Specifications for the ConnectCore 6 Plus Environmental specifications Global power consumption The following table lists the global power consumption of the ConnectCore 6 and ConnectCore 6 Plus system-on-module when the system is under the use cases described above: Digi Embedded Yocto 2.4 Power consumption (mA @ 5 V) Use case ConnectCore 6 ConnectCore 6 Plus Suspend 144 151 Power-off 4.8 5.9 IDLE 380 460 Decoding video 577.94 610.6 (+150.
Specifications for the ConnectCore 6 Plus Environmental specifications Linux - Android users You can measure the processor junction temperature by entering the following shell command: cat /sys/class/thermal/thermal_zone0/temp Note Depending on the operating system, the junction temperature is displayed in milli °C or °C.
Assembly instructions Moisture sensitivity and shelf life Mounting Coplanarity Solder paste print Stencil SMT pick and place SMT process parameter reference Reflow profile ConnectCore 6 Plus Hardware Reference Manual 90 90 90 90 90 91 91 91 89
Assembly instructions Moisture sensitivity and shelf life Moisture sensitivity and shelf life The ConnectCore 6 Plus module is classified as a Level 3 Moisture Sensitive Device in accordance with IPC/JEDEC J-STD-020. 1. Calculated shelf life in sealed packaging: 12 months at <40°C and <90% relative humidity (RH). 2. Environmental condition during production: 30°C / 60% RH according to IPC/JEDEC J-STD033C paragraph 5. 3.
Assembly instructions SMT pick and place SMT pick and place n Placement nozzle: Largest available on the machine n Nozzle pick surface: Center of shield n Placement speed: Slowest speed for the machine n Placement alignment: 10% of pad diameter (compensating for module weight and supporting alignment). The module should be placed last as part of the assembly/mounting process to eliminate unexpected shifting.
Assembly instructions Reflow profile Digi recommends you use two (2) thermocouple locations to achieve proper attachment of SoM: n Attach thermocouple to bottom of SoM located in the center of the cutout with the thermocouple touching the SoM. n Drill hole through bottom of carrier PCB near corner of SoM deep enough to reach SoM. n Insert thermocouple into hole touching SoM and secure. Digi recommends X-ray analysis after reflow to confirm proper mounting and solder reflow.
Regulatory information and certifications United States FCC Canada (ISED) Europe ETSI and UKCA Bluetooth SIG-qualified hardware and firmware Japan ConnectCore 6 Plus Hardware Reference Manual 94 97 98 102 103 93
Regulatory information and certifications United States FCC United States FCC The ConnectCore 6 Plus module complies with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required. To fulfill FCC Certification, the OEM must comply with the following regulations: The system integrator must ensure that the text on top side of the module is placed on the outside of the final product.
Maximum transmit power at antenna connector Frequencies RF band Peak antenna gain Technology 2.4 GHz 2.5 dBi BT + EDR 8.8 mW (+9.5 dBm) [BW 1 MHz] x 79 non-overlapping channels, # (center freq. MHz): * [2400 - 2483.5 MHz]: 0 (2402) to 78 (2480) Bluetooth LE 1.7 mW (+2.3 dBm) [BW 2 MHz] x 40 non-overlapping channels, # (center freq. MHz): * [2400 - 2483.5 MHz]: 0 (2402) to 39 (2480) WLAN 66.7 mW (+18.2 dBm) [BW 20 MHz] x 11 overlapping channels, # (center freq.
Regulatory information and certifications United States FCC FCC notices IMPORTANT: The ConnectCore 6 Plus module has been certified by the FCC for use with other products without any further certification (as per FCC section 2.1091). Modifications not expressly approved by Digi could void the user's authority to operate the equipment. IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section 15.107 & 15.
Regulatory information and certifications Canada (ISED) YAGEO ANTX100P001B24003 has been tested, but is not approved with standard firmware provided with the module. Please contact Digi Technical Support to receive dedicated calibration files / firmware to support this antenna. These files are reducing 2.4GHz output power to compensate for the higher gain of the YAGEO antenna.
Regulatory information and certifications Europe ETSI and UKCA Labeling requirements Labeling requirements for Industry Canada are similar to those of the FCC.
Maximum transmit power at antenna connector Frequencies RF band Peak antenna gain Technology 2.4 GHz 2.5 dBi BT + EDR 4.9 mW (+6.9 dBm) [BW 1 MHz] x 79 non-overlapping channels, # (center freq. MHz): * [2400 - 2483.5 MHz]: 0 (2402) to 78 (2480) Bluetooth LE 1.6 mW (+2.0 dBm) [BW 2 MHz] x 40 non-overlapping channels, # (center freq. MHz): * [2400 - 2483.5 MHz]: 0 (2402) to 39 (2480) WLAN 55.8 mW (+17.5 [BW 20 MHz] x 13 overlapping channels, # (center freq. MHz): * [2400 - 2483.
Technology Frequencies dBm) * [5250 - 5350 MHz]: 58 (5290) * [5470 - 5725 MHz]: 106 (5530) 7.
Regulatory information and certifications Europe ETSI and UKCA CE and UKCA OEM labeling requirements The CE and UKCA markings must be clearly visible and legible when you affix it to the product. If this is not possible, you must attach these marks to the packaging (if any) or accompanying documents. CE labeling requirements The “CE” marking must be affixed to a visible location on the OEM product. The following figure shows CE labeling requirements.
Regulatory information and certifications Bluetooth SIG-qualified hardware and firmware See https://www.gov.uk/guidance/using-the-ukca-marking for further details.
Regulatory information and certifications Japan You can combine these hardware and firmware elements into a new end product that is Bluetooth Sig-qualified with no additional Bluetooth testing, as long as you do not introduce any modifications to the Bluetooth design. Japan 電 波 法により5GHz帯 は屋内 使 用 に限ります。 This device has been granted a designation number by Ministry of Internal Affairs and Communications according to: Ordinance concerning Technical Regulations Conformity Certification etc.
Regulatory information and certifications Japan Approval Label (MIC Marking) Label text Note End product label should support radio marking for Japan. If not, radio marking shall be documented in the user manual. Note The warning “5GHz (W52, W53) band is for indoor use only (Excluding communication with registered stations)” must go on the end product – or E Label (Display).
