ConnectCore ® 6 ConnectCore for i.
Revision Record Revision Date (MM/YYYY) Description A 10/ 2014 First release B 01/2015 Updated For WiFi/Bluetooth variant labeling requirements Copyright and Trademarks © 2014 Digi International Inc. All rights reserved. Digi, Digi International, the Digi logo, and ConnectCore 6® are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the property of their respective owners.
ConnectCore for i.MX6 Hardware Reference Manual Table of Contents Using this Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Conventions used in this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Digi Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Document Updates . . . . . . . . . . . . . . . . . . . . . . .
ConnectCore for i.MX6 Hardware Reference Manual Table of Contents Antenna ports: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Security/Interoperability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Frequency Bands . . . . . . . . . . . . . . . . . . . . .
ConnectCore for i.MX6 Hardware Reference Manual Using this Guide This guide provides information about the Digi ConnectCore for i.MX6 embedded core module family. Conventions used in this guide This table describes the typographic conventions used in this guide: This convention Is used for italic type Emphasis, new terms, variables, and document titles. monospaced type Filenames, pathnames, and code examples.
ConnectCore for i.MX6 Hardware Reference Manual About the ConnectCore 6 The ConnectCore 6 is an ultra-compact and highly integrated system-on-module solution based on the Freescale i.MX6 Cortex-A9 processor family. With processor speeds up to 1.2 GHz and fully interchangeable single-/dual-/quad-core variants, the ConnectCore 6 offers a truly future-proof platform solution with scalable performance and pre-certified wireless 802.11a/b/g/n and Bluetooth 4.0, including Bluetooth Low Energy connectivity.
ConnectCore for i.MX6 Hardware Reference Manual • ETM/ETB support • Support of i.MX6 typical interfaces: • 16/32-bit data/address bus • SATA II, 3.0Gbps (24-bit parallel bus, LVDS, HDMI, MIPI/DSI) • Cameras (20-bit parallel bus, MIPI/CSI) • MMC/SD/SDIO • 1x USB OTG with integrated PHY • 3x USB Host • 1x Host with integrated PHY • 2x Host with integrated HS-IC USB PHY • PCI Express Gen 2.
ConnectCore for i.MX6 Hardware Reference Manual Block Diagram of the Freescale i.MX6 The figure below shows the block diagram of the Freescale i.MX6 application processor. Not all functions are available on all processor variants. Block diagram of the ConnectCore 6 CPU The following figure below provides a high-level block diagram of the ConnectCore for i.MX6 module. © 2014 Digi International Inc.
ConnectCore for i.MX6 Hardware Reference Manual Block diagram of ConnectCore 6 Power Supply Architecture of the ConnectCore 6 The ConnectCore for i.MX6 provides a primary 5V power supply input. This supply is the main power domain to the on-module Dialog DA9063 power management IC (PMIC), which generates all required supply voltages for the module components as well as the carrier board.
ConnectCore for i.MX6 Hardware Reference Manual The table below provides the characteristics of the optional LDO outputs: LDO Output Output Default voltage accuracy voltage Turn Maximum Dropout voltage Turn on time off current (MAX) (MAX) time (MAX) Quiescent current in OFF mode (TYP) VLDO3 0.9-3.44V +/-3% 3.3V 200mA 150mV 1µA 300µs 1ms VLDO4 0.9-3.44V +/-3% 3.3V 200mA 150mV 1µA 300µs 1ms VLDO6 0.9-3.6V +/-3% 3.3V 200mA 150mV 1µA 200µs 1ms VLDO7 0.9-3.6V +/-3% 1.
ConnectCore for i.MX6 Hardware Reference Manual As shown in the table above, the supplies have a wide operating range. In order to provide the most cost-effective and flexible solution for a given use-case, the supplies listed in the table need to be provided by the carrier board integrating the ConnectCore for i.MX6 module. However, PMIC power domains 3.3V - and LDO3/4/6/7/8 options - are dedicated power sources for supplying i.MX6 power domains.
ConnectCore for i.MX6 Hardware Reference Manual Bootstrap The ConnectCore 6 is configured by default to boot in “Internal boot” mode. See the following table: BOOT_MODE [1:0] Boot type 00 Boot from fuses 01 Serial Downloader 10 Internal Boot (default) 11 Reserved Note: • 10K pull-up populated on BOOT_MODE1 • 10K pull-down populated on BOOT_MODE0 By default, the boot media configured on the ConnectCore for i.MX6 module is the on-module eMMC.
ConnectCore for i.MX6 Hardware Reference Manual Module Pinout of the ConnectCore 6 The module has a LGA pad structure based on 400 pads. See the following diagram for the general layout. ConnectCore top view module pinout © 2014 Digi International Inc.
ConnectCore for i.MX6 Hardware Reference Manual ConnectCore 6 Pinout Information The following table provides pinout information of the ConnectCore for i.MX6 module. Additional timing and electrical information can be found in either Freescale i.MX6 processor datasheet (www.freescale.com) or in Dialog DA9063 product datasheet (www.dialogsemiconductor.com).
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.MX6 Hardware Reference Manual W23 W24 Y1 Y2 EIM_DA1 EIM_DA4 ENET_REF_CLK ENET_RXD0 Y3 ENET_MDIO Y4 GND Y5 RGMII_TD2 © 2014 Digi International Inc.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.MX6 Hardware Reference Manual AA8 AA9 DISP0_DAT8 DISP0_DAT4 ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: IPU1_DISP0_DATA08 IPU2_DISP0_DATA08 PWM1_OUT WDOG1_B ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: IPU1_DISP0_DATA04 IPU2_DISP0_DATA04 ECSPI3_SS1 NVCC_LCD GPIO4_IO29 NVCC_LCD GPIO4_IO25 AA10 VLDO6 VLDO6 AA11 VLDO7 VLDO7 AA12 GEN_3V3 GEN_3V3 AA13 AA14 EIM_WAIT EIM_A23 AA15 EIM_D31 AA16 GND AA17 EIM_D25 © 2014 Digi International Inc.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.
ConnectCore for i.MX6 Hardware Reference Manual AC8 AC9 DISP0_DAT0 DISP0_DAT1 ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: IPU1_DISP0_DATA00 IPU2_DISP0_DATA00 ECSPI3_SCLK ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: IPU1_DISP0_DATA01 IPU2_DISP0_DATA01 ECSPI3_MOSI NVCC_LCD GPIO4_IO21 NVCC_LCD GPIO4_IO22 AC10 MCA_VREFH - AC11 Reserved - AC12 GND - AC13 GND - AC14 PMIC_ADCIN2/ GPIO1 - AC15 AC16 AC17 AC18 EIM_CS1 EIM_A21 EIM_A17 GND © 2014 Digi International Inc.
ConnectCore for i.
ConnectCore for i.MX6 Hardware Reference Manual AD9 DISP0_DAT2 ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: IPU1_DISP0_DATA02 IPU2_DISP0_DATA02 ECSPI3_MISO NVCC_LCD GPIO4_IO23 AD10 VLDO4 - AD11 VLDO8 - AD12 PMIC_GP_FB3 - PMIC AD13 PMIC_GP_FB1/ GPIO13 - PMIC AD14 PMIC_ADCIN3/ GPIO2 - PMIC AD15 AD16 AD17 AD18 EIM_A16 EIM_A19 EIM_A24 EIM_D27 © 2014 Digi International Inc.
ConnectCore for i.MX6 Hardware Reference Manual AD19 AD20 EIM_D26 ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: EIM_DATA26 IPU1_DI1_PIN11 IPU1_CSI0_DATA01 IPU2_CSI1_DATA14 UART2_TX_DATA GPIO3_IO26 IPU1_SISG2 IPU1_DISP1_DATA22 EIM_D16 ALT0: ALT1: ALT2: ALT3: ALT4: ALT5: ALT6: ALT7: EIM_DATA16 ECSPI1_SCLK IPU1_DI0_PIN05 IPU2_CSI1_DATA18 HDMI_TX_DDC_SDA GPIO3_IO16 I2C2_SDA NVCC_EIM NVCC_EIM Signal Usage Limitations The following signals available on ConnectCore for i.
ConnectCore for i.MX6 Hardware Reference Manual Module Specifications Mechanical specifications Note that all dimensions are in millimeters. ConnectCore 6 module weight is 27 grams. © 2014 Digi International Inc.
ConnectCore for i.MX6 Hardware Reference Manual There must be a recess in the host PCB to accommodate the components on the bottom side of the SOM. All dimensions are in millimeters. For additional information, see Digi Application Note #31-31-14-x on the Digi technical support website. Host PCB Footprint 50 0.89 NON ROUTING AREA (3X) 2 1 23.20 25 R1 19 16.75 2 13.75 1 21 25 50 21 7.25 21.20 2 5 16.50 Note: Minimum thickness of the host board shall be 2mm. © 2014 Digi International Inc.
ConnectCore for i.MX6 Hardware Reference Manual Specifications for the ConnectCore 6 Environmental Specifications The Freescale i.MX6 thermal specification is based on maximum junction temperature (Tj) of the specific application processor variant used. In order to support thermal management assistance through software, the Freescale i.MX6 processor has a built-in junction temperature sensor/ monitor.
ConnectCore for i.MX6 Hardware Reference Manual on-module peripherals used.Your specific system design and application may require additional thermal management such as passive (heatsink/-spreader) or active (airflow) cooling at elevated temperatures. ConnectCore 6 Variant Ambient Operating Temperature1 Storage Temperature Industrial -40 to 85oC -40 to 125oC Commercial 0 to 70oC -40 to 125oC 1 Please note that ambient operating temperature ratings are highly dependent on the specific use-case, e.
ConnectCore for i.MX6 Hardware Reference Manual Solder Paste Print The following solder paste printing parameters are recommended: • Stencil Thickness: 0.15 mm/5 mil • Stencil Diameter: One to one of Pad diameter (to +20% of pad) • Paste alignment: 20% off the pad max (offset <20% pad diameter) Stencil The recommendation is to use a laser cut and/or electro-formed stencil for placing the ConnectCore 6 module.
ConnectCore for i.MX6 Hardware Reference Manual PnP Reflow Placement nozzle 0>15mm vacuum Nozzle Pick Surface PnP cap center Speed Slowest speed for the machine Placement Sequence Place the SoM last Placement Alignment 50% off the pad (offset <.5* diameter) Belt speed 0.6-1.1 m/sec Refer to SMT profile recommendation in the next page Reflow Profile Using Seven Zone Oven, SAC 305Lead-Free Solder Paste (Alpha OM-340) Time Above Liquidous (TAL) is recommended to be between 56 to 63 seconds.
ConnectCore for i.MX6 Hardware Reference Manual Network Interface WLAN Standard: • IEEE 802.11a/b/g/n standards • HT20, and HT40 IEEE 802.11n Frequency Band: • 2.40-2.50 GHz (low band) • 5.18-5.825 GHz (High band) Data Rates: • • • • • • 802.11b: 1, 2, 5.5, 11 Mbps 802.11a/g: 6, 9, 12, 18, 24, 35, 48, 54 Mbps 802.11n HT20 FGI: 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps 802.11n HT20 HGI: 7.2, 14.4, 21.7, 29.9, 43.3, 57.8, 65, 72.2 Mbps 802.11n HT40 FGI (5GHz only): 13.5, 27, 40.5, 54, 81, 108, 121.
ConnectCore for i.MX6 Hardware Reference Manual The picture below shows the location of the primary and secondary antennas. Note: Modules with Bluetooth capabilities will not support spatial diversity. Modulation Mode Data Modulation Mode rate 802.11b 1 DBPSK 2 Mode Modulation Mode Data rate Modulation 802.11g 6 BPSK 6 BPSK DQPSK 9 BPSK 9 BPSK 5.
ConnectCore for i.MX6 Hardware Reference Manual MCS2 QPSK 19.5 21.7 40.5 45 MCS3 16-QAM 26 29.9 54 60 MCS4 16-QAM 39 43.3 81 90 MCS5 64-QAM 52 57.8 108 120 MCS6 64-QAM 58.5 65 121.5 135 MCS7 64-QAM 65 72.
ConnectCore for i.MX6 Hardware Reference Manual Japan • 2.412 to 2.472 GHz; 13 channels • 5.180 to 5.320 GHz; 8 channels • 5.500 to 5.700 GHz; 11 channels Ad-Hoc Mode Channels • 2.4GHz Band - Channels 10 and 11 • 5GHz Band US, Australia, New Zealand - Channels 36, 40, 44, 45, 149, 157, 161, and 165 Channels 36, 40, 44, and 45 are for indoor use only • 5GHz Band Europe and Japan - per 802.
ConnectCore for i.MX6 Hardware Reference Manual 140 5700 HT20 159 5745 HT40 151 5755 HT20 153 5765 HT40 MINUS 157 5785 HT40 PLUS 159 5795 HT20 161 5805 HT40 165 5825 HT20 PLUS MINUS Receive Sensitivity Network type Sensitivity 802.11b -88 dBm 802.11g -88 dBm 802.11n (2.4GHz) -89 dBm 802.11a -90 dBm 802.11n (5GHz, HT20) -90 dBm 802.11n (5GHz, HT40) -86 dBm Transmit Power Network type Transmit power 802.11b 10.5 dBm 802.11g/n 11 dBm 802.
ConnectCore for i.MX6 Hardware Reference Manual Note: No specific ESD protection components have been implemented on the ConnectCore for i.MX6 module. ESD protection level on the module’s I/Os is the same as what is specified in the freescale datasheet. Any required ESD protection must be implemented on the carrier board. Power Consumption The following image displays the current consumption of the ConnectCore for i.MX6 module when booting respectively through U-Boot, Linux kernel and Android user space.
ConnectCore for i.MX6 Hardware Reference Manual Use case Description Power consumption Idle Mode Android 4.2.2: - No WiFi - No Bluetooth - No Ethernet (Gigabit Ethernet PHY on SBC is disabled) - HDMI display (standard PC display) - USB mouse - Console port 5VDC - 435mA Idle Mode - no USB Android 4.2.
ConnectCore for i.MX6 Hardware Reference Manual Certifications Agency Certifications United States FCC The ConnectCore™ for i.MX6 Module complies with Part 15 of the FCC rules and regulations. Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required. To fulfill FCC Certification, the OEM must comply with the following regulations: • The system integrator must ensure that the text on top side of the module is placed on the outside of the final product.
ConnectCore for i.MX6 Hardware Reference Manual IMPORTANT: The ConnectCore™ for i.MX6 module has been certified for remote and base radio applications. If the module will be used for portable applications, the device must undergo SAR testing. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ConnectCore for i.MX6 Hardware Reference Manual RF Exposure WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance are not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
ConnectCore for i.MX6 Hardware Reference Manual Declarations of Conformity Digi has issued Declarations of Conformity for the ConnectCore™ for i.MX6 module concerning emissions, EMC and safety. Files can be obtained by contacting Digi Support. Note: Digi does not list the entire set of standards that must be met for each country. Digi customers assume full responsibility for learning and meeting the required guidelines for each country in their distribution market.
ConnectCore for i.MX6 Hardware Reference Manual Le présent émetteur radio (IC: 1846A-CCIMX6 / IC: 1846A-CCIMX6B) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
