User's Manual

ManualsBrandsDigi-Code ManualsElectronicsGarage Door Remote Control

Installation Instructions

Garage Door Opener Radio Controls

Model 5010 (300 mHz) \ 5012 (310 mHz) Single Button Transmitters

Model 5020 (300 mHz) \ 5022 (310 mHz) Dual Button Transmitters

Model 5190-01 (300 mHz) \ 5190-02 (310 mHz) Receivers

WARNING:

•• Disconnect operator power before any installation or repair

•• Always wear safety glasses

Your Digi-Code radio controls are designed specifically to remotely control a garage

door opener from within an automobile and to give years of trouble free service without

adjustment. Because all radio controls are set with the even numbered switches in the

“ON” position when they leave the factory, it is recommended that a different code

be selected and set at the time of installation. Please refer to the “Setting the Code

Switch” section for instructions. The radio frequency (RF) portion of the controls,

however, are tuned to standard frequencies and are thoroughly tested at the factory. This

permits the addition or replacement of either the transmitter or the receiver by specifying

the Model number and the RF frequency designated on the identification label. RF

adjustments are not needed nor should any be attempted.

RECEIVER INSTALLATION

The receiver is designed to mount directly to the operator. It can be remotely installed if

the operator terminal strip is not accessible, or if the power for the receiver is not

obtainable from the operator. To direct mount the receiver, simply loosen the terminal

screws on the operator and insert the two-way lugs from the receiver under the screw

heads along the wall button wires, and tighten the screws ( See Figure #1)

Place the antenna (a 10 inch black wire ) in a vertical position as far from any metal as

possible.

Summary of content (5 pages)

PAGE 1
Installation Instructions Garage Door Opener Radio Controls Model 5010 (300 mHz) \ 5012 (310 mHz) Single Button Transmitters Model 5020 (300 mHz) \ 5022 (310 mHz) Dual Button Transmitters Model 5190-01 (300 mHz) \ 5190-02 (310 mHz) Receivers WARNING: • Disconnect operator power before any installation or repair • Always wear safety glasses Your Digi-Code radio controls are designed specifically to remotely control a garage door opener from within an automobile and to give years of trouble free service with
PAGE 2
For remote installation the receiver may be mounted near the operator head on a joist or the ceiling by using the mounting tab. Order Model 5192-06 adapter, which permits connection between the operator terminal and the two-way lugs on the receiver. Slip on connectors at one end of the adapter connect to the flat side of each spade lug on the receiver, and the spade connectors at the other end connect to the operator terminal.
PAGE 3
Connect wires as follows: (a) (b) (c) (d) White wire to terminal “1” or “24v” Black wire to terminal “2” or “Relay” Red wire to terminal “3” or “Common” ( Radio Power ) Connect push button wires to terminal “1” and “2” (See Figure #2) Where power for the radio receiver is not available from the operator order a Model 5192-01 power transformer adapter for connection between the operator and the remote receiver.
PAGE 4
Set both code switches to the code of your choice, being sure both are set the same since a different setting of just one switch will prevent operation. The digital code is determined by the position of the 10 small switches numbered 1 through 10 located in the receiver and the transmitter. Any combination of “on” or “off” positions can be selected by using a pencil or a pen. (Note: The switches are in the “on” position when the switch is depressed toward the number.) See Figure #3 above.
PAGE 5
SETTING THE TRANSMITTER CODE SWITCH – MODEL’S 5020 & 5022 On the transmitter the entire front lower half of the case ( “ the battery hatch” ) is removeable. Use a coin or the curved end of the visor clip to disengage the lower half of the transmitter front. This will expose both the code switch and the battery compartment Once you have done this, locate the code switch and set code switch positions 1 through 9 to your personal code scheme ( THE 10TH POSITION SWITCH MUST BE SET IN THE CLOSED POSITION “ON” ).