FCC TEST REPORT Report No.: EMC-FCC-R0078 http://www.emc2000.co.kr Appendix 6. User manual EMC compliance Ltd. Page: 1 of 1 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.
Rearview Monitor Model : RVM-804 USER MANUAL( Ver 1.0) Table of Contents 1. 2. 3. 4. 5. 6. Caution Components of the product How to use the product How to install the product Product Specification Warranty statements • Thank you for purchasing our touchscreen vehicle monitor. • Please read this manual before you use the product. • The product may be different than described in the manual; depending on renewal and/or upgrade of S/W version and performance it can be altered without notice.
1. Caution ● For your safe operation, operation please read this manual before you start to use the product. We inform you that our company shall not be responsible for failures and troubles that are occurred due to misuse or neglect of the cautions written on this manual. ● Operating this equipment when driving a vehicle might cause an. accident. Use the equipment after parking or stopping the vehicle in a safe area.
2.Components of the product ① ②③ ①Touch Screen ● By touching one of the small picture during multi screen mode, the concerning small picture will be enlarged into full screen mode. ● By touching the screen it is possible to control the equipment or to change the settings. ②Power On/Off ● Press the power button for 0.5 seconds to turn on the screen. ● Press the p power button for 0.5 seconds to turn on the screen when it is turned on.
④⑤⑥⑦ ④ Bluetooth phone menu On/Off ● Bluetooth phone menu screen appears when you touch the button. ⑤ LCD Display On/Off ● Lcd screen appears when you touch the button. ⑥ Split Screen ● A split screen appears appears. ⑦ Menu Button ● The main menu appears.
Rear Panel ① ③ ④ ② ①Power Input ● Connect the power cable. ( VCC/GND/TRG1~TRG5/Speed SW ) ②Camera Input ● Connect the camera cable. ( Cam1 ~ Cam4 ) ③ AUX In ● AUX in 2 port ④ Ext. MIC / Speaker p ● Connect an external mic and speake..
Components ● Please check that you have the correct contents before using this Product. ● If any items are missing, please contact your dealer.
3. How to use the product Start screen ● When the booting is ready, the multi screen as below will be displayed When the small window is touched, it is enlarged. ● When the small window on the multi screen are touched, the channel is enlarged into full screen mode. One more touch returns it back to the multi screen mode. ● : Adjust the volume of the speaker. ● : Setting menu. .
Volume Control ● Press the button to display volume Pop-up. ② ① ① Press the button to mute. ② Press the button to increase the volume. ③ Press the button to decrease the volume volume.
Multi screen ● P Press th the multi lti screen b button tt tto di divide id th the screen.
Setting Mode ● P Press th the setting tti menu b button tt tto open th the setting tti screen.
Display Input the name into each channel.
Display Setup screen position of each channel ※ Caution: Cam1and AUX1 cannot be setup at the same time. Setup the screen on each trigger.
Display Display Di l th the ffullll screen according di tto each h Channel setup when setting up On Display the dividing lines of the screen
Display Adjust Parking line of each Trigger. Calibration Trig 1 Trig.
Function The screen iis tturned Th dO On automatically t ti ll When starting the vehicle 전원 Off 전의 화면Mode로 On됩니다.
Function Keep Trigger activated during setup time after Trigger off in order to bridge temporary powerloss, e.g. from vehicle’s turnlight signal Re-adjust center Point of Touch panel STEP 1 of 3 Click on center of '+' icon for Touch screen calibration.
Function Detect speed of a vehicle from 10 to 200Hz To switch automatically into the screen ON mode, by detecting a speed signal (tacho signal)
System Set time displaying the Menu screen. Set time displayed on the screen screen. 설정시간 동안 Touch등 Key 입력이 없으면 화면이 꺼집니다.
System Set a password to lock the Menu button. Support languages for each country.
System Initializing set points of Menu Display Firmware Version and Model name
Bluetooth Phone ● Press the button to start Bluetooth. Screen of Bluetooth start Start-up screen displays the Phone Book list of phone paired. : Displays call lists during absence. : Di Displays l phone h callll lilists t received. i d : Displays phone call lists sent. : Use for making a call dialing numbers. : Displays a Phonebook list. : Setup of Bluetooth. : Finishes Bluetooth.
Bluetooth Phone ● Enter the Pairing Mode for Paring with Bluetooth by pressing the button 1. Pairing mode is set by pressing the button. 2. Connect Bluetooth to a cell phone you want searching Bluetooth device.(Enter the Pin code depending on type of cell phones) 3. Message is displayed when it is connected as below. 4 Return to the start 4. start-up up screen of Bluetooth by pressing the button.
Bluetooth Phone ● : Displays devices Paired.
Bluetooth Phone ● ● :Connection automatically when receiving a call :Incoming call automatically after a set time when receiving a call from the set on the state. •Name : Phone on display during Pairing is the name of that instrument. • Address : Bluetooth Address. • Bluetooth Soft ware Version is displayed.
Bluetooth Phone ● Down load phonebook list after pairing succeed. •Call after press the number in the list.
4.
6.Specification - LCD : Built in 8“ TFT LCD (WVGA 800x480, with Touch Panel) - Camera : 4Ch input (1 Vp-p, 75Ω) /NTSC, PAL ( Video & Audio ) - Audio Output p 1Ch - AUX1, AUX2 - Trigger 5 input (Cable Input : 12 ~ 24V) - ALS Sensor (Night & Daytime Brightness detection) - Power : 12~24Vdc (12Vdc 1.3A) - Operating Temp. : -20’C ~ 55’C - Storage Temp.