Purchaser’s Reference Information IT IS IMPERATIVE THAT YOU FILL IN THE FOLLOWING INFORMATION AND REFER TO IT SHOULD THE NEED FOR SERVICE ARISE. Product Name: Diamondback 650T/660T ___________ Serial Number: H To Activate Warranty: COMPLETELY FILL OUT THE ATTACHED WARRANTY CARD (SEE BACK COVER) AND RETURN TO DIAMONDBACK WITHIN 15 DAYS OF THE DATE OF PURCHASE. FAILURE TO COMPLY WITH THE WARRANTY ACTIVATION PROCEDURE MAY VOID THE MANUFACTURER’S WARRANTY.
Table of Contents • • • • • • • Purchaser’s Reference Information ................................... 2 Introduction ....................................................................... 4 Features ............................................................................ 5 Safety Instructions and Warnings ..................................... 6 660T Assembly Instructions ............................................. 7 650T Assembly Instructions .............................................
Introduction Good health is an exercise in common sense. The basics of good health are really common sense. Eat right, drink lots of water, get enough sleep, and exercise at least 3-4 times a week. It may sound simple, but to achieve the look and vitality most health-conscious men and women want, takes more discipline than most people are willing to endure. Having fitness equipment in your home makes it easier to achieve your goals. And having Diamondback equipment gives you even more of an edge.
Features 660T Folded Position Console Reading Rack & Accessory Holder Safety Key Handrail Upright Post Horizontal Handlebar On/Off Switch Motor Cover 5 Running Belt Step Rail Belt Adjustment 660T Folding Lock Release 600 SERIES TREADMILL O W N E R’ S M A N U A L
Instructions and Warnings The 650T/660T treadmills are built for optimum safety and are designed to meet or exceed all domestic and international standards. However, certain precautions need to be followed when operating any exercise equipment. BE SURE TO READ THE ENTIRE OWNER’S MANUAL BEFORE OPERATING YOUR 650T/660T UNIT. ATTENTION - DO NOT OPERATE THE HEART RATE MONITOR TRANSMITTER TOGETHER WITH AN ELECTRICAL HEART PACEMAKER. THE TRANSMITTER MAY CAUSE ELECTRICAL DISTURBANCES.
660T Assembly Instructions WARNING: FOLD THE TREADMILL UP BEFORE REMOVING FROM THE BOX. Upright Posts Assembly 1. Connect the wire harness connectors before assembling Left upright post into the upright post receptor of the base frame. 2. Slide the Left upright post into the receptor. Locate the L shaped upright brace. Insert 4 bolts with washers into the post, making sure the rear 2 bolts go through the upright brace. Insert 1 bolt with washer through the remaining hole in the upright brace.
650T Assembly Instructions Upright Posts Assembly 1. Connect the wire harness connectors before assembling Left upright post into the upright post receptor of the base frame. 2. Slide the Left upright post into the receptor, insert 4 bolts with washers, and slightly tighten with an Allen wrench. Be careful not to pinch the wire harness when installing. (See figure A.) 3. Assemble the Right upright post with the same procedure as Left upright post.
Exercise Guidelines Anyone over the age of 35, as well as younger persons whom are overweight, should check with his/her physician before beginning any type of exercise program. People who have diabetes or high blood pressure, a family history of heart disease, high cholesterol or have lead a sedentary lifestyle should protect themselves with a medical check-up and a stress test, preferably administered during exercise by a healthcare professional.
Console Layout Data Windows Safety Key 10 Elevation Adjustment Keys Program Selection Keys Speed Adjustment Keys Safety Key and Clip The safety key is designed for safety use only. When you pull the safety key, it will cut the power to the treadmill and bring the treadmill to an immediate stop. Press the “Stop” button if you need to stop the treadmill. Do not pull the safety key unless it is for an emergency stop. The treadmill will not restart until safety key is re-engaged on the console properly.
Getting Started The 650T/660T are designed and manufactured for home use with a maximum utilization time of 1 hour per day / 7 days per week. User weight capacity is 300 lbs. / 135 kgs. • Place this treadmill on a firm level surface. • Make sure every part on this treadmill is secure and tightened. • Plug power cord into the wall outlet, 110V • Ensure the safety cord and clip are in engaged. • Initialize the 650T/660T by turning the power switch to the “ON” position.
Programs PROGRAMS - QUICK START Beginning the Program Stop or Reset the Program • Press “START” key to begin the program • The console will start a 3 second count down • Begin workout • To Stop this program, press “STOP” key once. The console will Stop the program. At this time, all the data window will show the end of workout information, the Speed will return to 0 MPH and Elevation will return to 0%. • To Reset this program, press “STOP” key after the program stops.
Programs SPEED PROGRAMS - Speed Interval Program (P1); Weight Loss Program (P2)) Beginning the Program • Press “SELECT” key once to enter the program mode. At this time, the CAL./PULSE window will show “P1” and the speed window will show top speed of “6.0”. • Press + - key to select the desired program, P1 for Speed Interval Program and P2 for Weight Loss Program. Please see attached speed charts for program details. • User may adjust the program’s top speed setting, the default top speed is 6.0 MPH.
Programs ELEVATION PROGRAMS - Fat Burner Program (P3) ; Cross Country Program (P4) ; Hill Climb Program (P5) Beginning the Program Program Notes • Press “SELECT” key once to enter the program mode. At this time, the CAL./PULSE window will show “P1”. • Press + - key to select the desired program, P3 for Fat Burner Program, P4 for Cross Country Program and P5 for Hill Climb Program. At this time, elevation window will display “8%”. Please see attached elevation charts for program details.
Programs USER TARGET PROGRAMS - Distance Target Program ; Calories Target Program ; Time Target Program Distance Target Program Beginning the Program Stop or Reset the Program • Press “SELECT” key Twice to enter the Distance Target program. At this time, the Distance window will show “2.0”. • Press + - key to set the Target Distance.
Programs Time Target Program • Press “SELECT” key Four times to enter the Time Target program. At this time, the Time window will show “20:00”. • Press + - key to set the Target Distance. • Press “START” key to accept the setting and begin the program • The console will start a 3 second count down • Begin workout During Workout, user may Adjust Speed • The Speed window is displaying the default speed: 0.5MPH.
Domestic Warranty Information (Applies to all product sold and placed within the continental US only) Effective: August 2001 Diamondback warrants its 650T/660T to be free from defects in material and workmanship under normal use in the home.
Maintenance Always inspect hardware prior to any exercise session. Turn power switch to the “OFF” position and unplug electrical cord from the outlet before attempting maintenance. Inspect unit for loose parts and frayed wires. Repair or replace any damaged or worn parts, tighten all loose hardware as necessary. After training, always wipe down your 650T/660T unit. Perspiration that continuously settles on frame, pads or casing may eventually cause rust or damage to the unit.
Marking Label MODEL: 650T RATING: 120 VAC, 60 Hz, 900 W 3031266 Diamondback Fitness a division of Raleigh America, Inc. CONFORMS TO UL STD. 1647 CERTIFIED TO CAN/CSA STD. C22.2 NO. 68 * THE FOLLOWING WARNINGS SHOULD BE MARKED PERMANENTLY ON THE CONSOLE OR SAFETY KEY OF THE TREADMILL: WARNING: REMOVE SAFETY KEY WHEN NOT IN USE AND STORE OUT OF REACH OF CHILDREN. AVERTISSEMENT: RETIRER LA CLÉ DE SÉCURITÉ QUAND L´APPAREIL N´EST PAS EN SERVICE, ET LA PLACER HORS D´ATTEINTE DES ENFANTS.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using the treadmill. DANGER - To reduce the risk of electric shock: 1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning. 1. An appliance should never be left unattended when plugged in.
GROUNDING INSTRUCTIONS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
IMPORTANT! IMPORTANT! IMPORTANT! IMPORTANT! Warranty Card must be completed and returned to Diamondback within days of purchase. Failure to comply may void manufacturer’s warranty.
Sales & Distribution Corporate Headquarters 300 Camarillo Ranch Road Camarillo, CA 93012 T 800-776-7642 • F 805-388-5890 22710 - 72nd Avenue South, Box 97072 Kent, WA 98032 T 253-395-1100 • F 253-872-0257 600 SERIES TREADMILL O W N E R’ S M A N U A L Part Number: 22-19-131 08-21-02