OKIMAT 8 OKIMAT 8+2 FURNIBUS Installation Instructions (Translation of the original installation instructions)
OKIMAT 8 Foreword Foreword Disclaimer and exclusion of liability DewertOkin is not responsible for damage resulting from: • failure to observe these instructions, • changes made to this product which have not been approved by DewertOkin, or • the use of replacement parts which have not been approved or manufactured by DewertOkin..
Table of contents OKIMAT 8 Table of contents Foreword 3 Disclaimer and exclusion of liability 3 Creation of a complete operating instruction manual for the entire end product 3 Notice for customers in EU nations 3 Table of contents 4 1. General Information 6 1.1 Safety notices within the installation instruction and the operating instructions for the entire machine 6 1.2 Conventions used 6 2. Safety notices 7 2.1 Proper and intended usage 7 2.
OKIMAT 8 Table of contents 10. Disposal 28 10.1 Packaging material 28 10.
General Information 1. OKIMAT 8 General Information These installation instructions must be followed closely in order to install this drive successfully and safely in the end product. These instructions are not an operating manual for the end product. These instructions will help you to minimize danger, repair costs and down times. They will also help you to maximize the reliability and lifespan of the end product.
OKIMAT 8 Safety notices 2. Safety notices 2.1 Proper and intended usage The OKIMAT 8 drive is meant to be installed in beds. • It provides motor adjustment capabilities for movable reclining bed parts. It should be used in conjunction with suitable fittings and mechanics: CAUTION Risk of accident This drive should only be used for the applications described above. Any other use is forbidden. Improper usage can lead to accidents or destruction of the unit.
Safety notices OKIMAT 8 Optional: battery-operated reset function NOTICE The battery-operated reset function is not a safety system and does not avert danger. DewertOkin does not guarantee that the drive will function in the event of a power outage. If the end-product manufacturer chooses to guarantee the functionality of the end product during a power outage, then the end-product manufacturer is responsible for arranging a mechanism to ensure this functionality. 2.
OKIMAT 8 Safety notices 2.4 Product identification 2.4.1 Ratings plate The ratings plate shown is an example; the specifications for your drive may differ from this illustration. Figure 2 Ratings plate example OKIMAT 8+2, OKIMAT 8+2 FURNIBUS Model name xxxxx Article number 24 – 29V Input voltage Max. 6.00A Current consumption Intermittent Operation 2min/18min Intermittent operations: 2 minutes / 18 minutes Max. force Push force Prod.date Calendar week / year 2.
Possible combinations 3. OKIMAT 8 Possible combinations The OKIMAT 8 double drive can be combined for use with other single or double drives. The following basic combinations are possible: • an OKIMAT 8 with a hand-held remote control, • an OKIMAT 8 as the main drive and a single drive used as a slave drive with a hand-held remote, • an OKIMAT 8 as the main drive and two single drives used as slave drives with a hand-held remote.
OKIMAT 8 4. Description Description The drives units are powered by electrical motors. The back and leg sections of a bed can be adjusted depending on the drive options. The drive is controlled by means of an OKIN controller.
Technical specifications 5. OKIMAT 8 Technical specifications Power supply (AC) or Input voltage (DC) 120 / 230 / 240 V, 50/60 Hz (refer to the ratings plate) Current consumption under rated load (AC) 0.63 A AC – 3.15 A AC, depending on mains connection and load (refer to the ratings plate) Current consumption under rated load (24 V DC) Max. 8.0 A DC Permitted push force Max. 6000 N Mode of operation1 under max. rated load. Intermittent duty 2 min./18 min.
OKIMAT 8 Technical specifications Dimensions of housing 119 179 714 Figure 4 Dimensions of OKIMAT 8 drive (in mm) Dimensions of the pivot lever 581 ± 2 74.6 R 11 480 ± 2 Figure 5 72 50.5 Pivot lever position, in mm Make sure that you consider the amount of torque that is generated by the drive when you design the weld between the bracket and the end product. • Max. torque: 435 Nm. We recommend: the OKIN pivot lever (ID number 2.00.718.108.
Installation OKIMAT 8 6. Installation 6.1 Safety notices to observe during installation Basic safety rules must be followed in order to ensure that the end product can be continually operated in a safe manner. These rules must be observed while using the end product and while installing the drive. Avoiding fatigue fractures Drives that are incorrectly installed can undergo fatigue fractures which then create a risk of injury. • Install the drive in the end product so that it is properly aligned.
OKIMAT 8 Installation 6.2 Installation procedure 6.2.1 An example installation Before installing the drive, make sure that you are observing all of the safety notices found in the "Safety notices to observe during installation" section. 1 Move your product into a position where it is supporting no load. CAUTION Danger of crushing injury! • Be sure to carry out work on the drive in a position so that no loads are bearing on it. Only in this way can you be sure to avoid any risks of crushing or injury.
Installation OKIMAT 8 Figure 8 Installing the double drive 4 Push the drive in so that the brackets (D) fit into the slots (B). Press in until the tubes snap into the brackets. 5 Close the shutters (A) on the drive by snapping them back in. The OKIMAT 8 is now securely attached to the end product. 6 Disconnect all additional components (handset, etc.) from their sockets. 7 Now connect the drive to the power supply.
OKIMAT 8 Installation Option: Connecting the OKIMAT 8 to an external switched-mode power supply (SMPS) The OKIMAT 8 should be connected to an external switched-mode power supply (SMPS: such as the PD12/PD13 power supply with the country-specific mains plug as described in the power supply's installation instructions) using a connecting cable, as shown in Figure 9.
Installation OKIMAT 8 Optional: battery-operated reset function Connecting the nine-volt batteries A B C B Figure 10 C Connecting the 9-V battery/batteries A Battery clip connected, B Battery clip, unattached C 9-V battery (type 6LR61) Connect the nine-volt batteries first when you would like to perform a battery-operated reset. The batteries may only be used to power the reset function one time. Take out the batteries and dispose of them properly after the reset function has been carried out.
OKIMAT 8 6.2.3 Installation Dismantling CAUTION Risk of accident • Work on electrical components should be conducted only when the mains power connection is unplugged. • Disconnect the nine-volt battery if you are using the battery-operated reset function. .. Certain details may change because of technical changes. Figure 11 Removing the double drive 1 Move your product into a position where it is supporting no load.
Installation OKIMAT 8 C Figure 12 D D Removing the double drive C End product (bed) D Brackets 6 Pull out the OKIMAT 8 far enough so that the brackets (D) are out of the slots (B). The OKIMAT 8 is now unattached and can be removed. A A B B Figure 13 A Shutters Removing the double drive B Fitting mounts 7 Push the shutters (A) back onto the OKIMAT 8 so that they are not lost during transportation. Close the optional locking device.
OKIMAT 8 7. Information about creating your Operating Manual Information about creating your Operating Manual The factual information contained within may be used when you are creating the end-product manual. The installation instructions do not contain all information required for the safe operation of the end product. They only describe the installation and operation of the drive as a partially assembled piece of machinery.
Information about creating your Operating Manual OKIMAT 8 Shutting off the drive To shut off the drive, first disconnect the system from the power supply and then disconnect the battery. The power supply must always be accessible during operations so that the system can be shut off. Avoiding cable damage Be sure that your operating instructions inform the user about the possible cable risks. NOTICE The cables (particularly the mains cable) should not be run over.
OKIMAT 8 Information about creating your Operating Manual 7.2 Notice for operating with optional configuration 7.2.1 Optional: battery-operated reset function The battery-operated reset function allows the drive system to be operated during a power outage. One or two 9-V batteries can be used to power the OKIMAT 8 in the event of a power outage. The batteries should be connected only then when the outage occurs. The batteries are not connected by default since they have very limited capacity.
Information about creating your Operating Manual 7.2.2 OKIMAT 8 Programming the RF hand-held remote A Figure 14 Function key on the OKIMAT 8 A Function key (at rear of the drive) 1 Press the drive's function key (A) twice (a quick double click). The drive will be in the teach-in (programming) mode for approximately 10 seconds. The LED on the function key lights up. More information on programming the hand-held remote and its key functions is provided in the hand-held remote's manual.
OKIMAT 8 7.2.3 Information about creating your Operating Manual Optional: integrated floor lighting The integrated floor lighting should only be used for illuminating under the bed. It is built into the front or back of the double drive, as shown in Figure 15. A B Figure 15 Location of the integrated floor lighting (optional) A Floor lighting on front B Floor lighting on back CAUTION Never look directly into the light from the floor lighting. Never point the floor lighting towards someone's eyes.
Troubleshooting 8. OKIMAT 8 Troubleshooting This chapter describes troubleshooting methods for fixing problems. If you experience an error that is not listed in this table, please contact your supplier. CAUTION Only qualified specialists who have received electrician training should carry out troubleshooting and repairs. Problem Possible cause Solution The handset or drive system is not functioning. There is no mains supply voltage. Connect the mains power.
OKIMAT 8 Maintenance 9. Maintenance 9.1 Maintenance The OKIMAT 8 drive requires no maintenance. 9.2 Cleaning and care Clean the OKIMAT 8 drive as needed using a dry cloth. NOTICE • Always disconnect the power supply before you start to clean the drive system! • Disconnect the nine-volt battery if you are using the battery-operated reset function. xxx.. • Never clean the OKIMAT 8 in an automated washing system or with a high-pressure cleaner. Do not allow fluids to penetrate the unit.
Disposal OKIMAT 8 10. Disposal 10.1 Packaging material The packaging material should be sorted into recyclable components and then disposed of in accordance with the appropriate national environmental regulations (in Germany according to the recycling law KrWG from 01.06.2012; internationally according to the EU Directive 2008/98/EC (Waste Framework Directive WFD as of 12.12.2008)). 10.2 Drive components The OKIMAT 8 drive consists of electronic components, cables and metal and plastic parts.
FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Section 15.21 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Declaration of Incorporation According to Appendix II of the EU Machinery Directive 2006/42/EC The manufacturer: DewertOkin GmbH Weststraße 1 32278 Kirchlengern Germany declares that the incomplete machine described below OKIMAT 8 complies with the following basic requirements of the Machinery Directive (2006/42/EC): Sections: 1.1.3; 1.3.3; 1.3.4; 1.3.7; 1.5.1; 1.5.2; 1.5.5; 1.5.6; 1.5.7; 1.5.8; 1.5.9; 1.5.10; 1.5.13; 1.6.
EU Declaration of Conformity In compliance with Appendix IV of the EU EMC Directive 2004/108/EC In compliance with Appendix III of the EU Low Voltage Directive 2006/95/EC In compliance with Appendix VI of the EU RoHS Directive 2011/65/EU In compliance with Appendix VII of the EU Directive 1999/5/EC (only for the 2.
DewertOkin GmbH Weststrasse 1 Kirchlengern 32278, Germany Tel: +49(0)5223/979-0 Fax.: +49 0 522375182 http://www.dewertokin.de Info@dewertokin.de ID No.
