Use and Care Manual

ManualsBrandsDEWALT ManualsGarage Shelving15 Amp GFCI 8-Outlet Power Station with Detachable Rechargeable Work Light/Cord Minder Set for Storage Rack

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-844-377-8451 • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DXSTA151PS

15 Amp Power Station with GFCI and Detachable Work Light

Station électrique 15 A avec DDFT et lampe de travail amovible

Central eléctrica de 15 AMP con GFCI y luz de trabajo desmontable

DEWA LT

and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an afliate

thereof and are used under license. The yellow/black color scheme is a trademark for

DEWALT power tools & accessories.

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

SAVE THESE INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Parts List

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL

FREE AT: 1-844-377-8451

Technical Specifications

POWER STATION

Height 5.5" (13.97 cm)

Width 14.75" (37.47 cm)

Depth 3.5" (8.89 cm)

Weight 3.5 lb (1.59 kg)

Amperage 15 AMP

CORD MINDERS

Total Capacity per 2 Piece

Cord Minder Set

50 lb (22.6 kg)

*when weight is evenly distributed

Holding Capacity Up to 100 ft of 10/3 Heavy Duty extension cord

No. Description

Qty.

1 Power Station with Lighted Handle

2 Mounting Bracket for DXST10000 Series (A)

3 Mounting Bracket for DXST4500 Series (B)

4 Cord Minder Bracket

5 Locking Pin

6 Mounting Screw

5 6

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave tools unattended.

• Never force a part into place.

• Wear safety apparel.

• Wear safety glasses/goggles.

• Never hang from the Cord Minders.

• Never crawl, sit, stand, or climb on the rack.

• Keep small parts away from children. Never leave small children unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION:

(Used without word) Indicates a safety related message.

Indicates a practice not related to personal injury which, if not avoided,

may result in property damage.

NOTICE:

NEVER EXCEED THE FOLLOWING WEIGHT LIMITS FOR THIS 2

PIECE CORD MINDER

• Maximum load per Cord Minder set is 50 lb (22.6 kg).

• Immediately remove the load should there be separation between the Cord Minder and the mounting bracket.

• Immediately remove the load should there be damage, bending or warping of the rack uprights or the

Cord Minders.

WARNING:

Serious injury or death can occur from the rack tipping over. To prevent this, the rack must

be secured to the wall, especially in earthquake-prone areas, or where surfaces are uneven, and where children

and/or pets are present. For added safety we recommend also mounting the rack to the floor using DEWALT part

number DXSTA04MP (sold separately).

NOTE: The Power Station and Cord Minders are to be used with your DEWALT DSXT10000 or DXST4500

Industrial Rack (not included).

SPECIFIC SAFETY FOR WALL MOUNT BRACKET

USE OF EXTENSION CORDS WITH WORKLIGHT

WARNING! Read and understand all instructions. This manual contains

important safety and operating instructions. Please read this manual carefully

before assembling this storage rack and save it for reference.

GENERAL SAFETY

READ ALL INSTRUCTIONS

BEFORE YOU BEGIN:

• Read all instructions thoroughly.

• Remove all components from the box, and lay them on the floor in an orderly fashion.

• Wear eye protection.

• Be cautious of sharp edges.

• Keep this information for further reference.

WARNING:

RISK OF FIRE OR EXPLOSION – Batteries should only be replaced by authorized

service technicians.

Keep electrical cords in good condition. Do not use worn, bare, or frayed cords because they

can cause electrical shock.

Operating equipment at low voltage can cause it to overheat. Using an excessively long

extension cord can cause the cord to overheat.

WARNING:

Serious injury or death can occur from the rack tipping over. To prevent this, the rack must

be secured to the wall, especially in earthquake-prone areas, or where surfaces are uneven, and where children

and/or pets are present. For added safety we recommend also mounting the rack to the floor using DEWALT part

number DXSTA04MP (sold separately).

1. Fully insert the Power Station plug into a 110VAC 60Hz power source.

2. Verify the circuit breaker switch is in the “Reset” position and the switch light is on indicating that power is

flowing through the unit.

3. The LED charging indicator for the removable work light handle will flash RED and GREEN to indicate reset

and will then remain illuminated. A constant RED LED means that recharging is in progress. A constant GREEN

LED means that the removable work light is fully charged. Allow the work light to charge fully before use.

4. Fully insert the plug of power tools or other electronic devices into a Power Station outlet (8 outlets total).

5. The Power Station is rated up to 15 amps. If the amperage draw exceeds the rating and the circuit breaker

powers off the Power Station, unplug all devices from the Power Station and set the circuit breaker switch to

the “Reset” position before resuming use.

6. This model is equipped with a Ground Fault Circuit Interrupter. A Ground Fault Circuit Interrupter shuts off an

electric power circuit when it detects that current is flowing along an unintended path. To reset the GFCI, unplug

all devices from the Power Station. Verify the circuit breaker is in the “Reset” position before resuming use.

7. Fully insert USB plugs into the USB ports (under rubber cap) at the end of Power Station to power or charge

devices with USB power ports.

Power Station Operation Instructions

Rechargeable Work Light Instructions

1. Rotate the handle to the desired position. Turn the work light on by depressing and releasing the power button

on the handle next to the LED lens. Depress and release the switch again to turn off.

2. To release the work light from the Power Station, depress the release button on the opposite side of the handle

from the work light on/off switch and pull the work light module up and away from the dock.

3. To recharge the work light module, return the light module to the dock on the Power Station. Verify the light

module aligns with the key way on the handle before fully inserting into the dock. The LED charging indicator

will turn RED indicating that recharging is in progress.

NOTE: This Power Station can be mounted to either the DXST4500 or DXST10000 racks, which are

sold separately.

1. Remove rubber feet from the bottom of Power Station to expose hang holes. (Fig. 1)

2. Select the mounting bracket for the correct rack upright:

• (A) Wider bracket fits DXST10000 Industrial Racks.

• (B) Narrower bracket fits DXST4500 series Industrial Racks.

3. Install the mounting bracket to the rack’s upright by aligning the tabs to the mounting holes, then slide

downward until secure. (Fig. 2)

4. Install locking pins. (Fig. 3)

Power Station Mounting to a Rack Instructions (Fig. 1-5)

2 3

Only use a grounded extension cord that is rated at least 12 amps and has a third-wire ground. When a long

extension cord is used to connect a power station or tool, a voltage drop occurs. The longer the cord, the greater

the voltage drop. This results in less voltage being supplied to the power station or tool and increases the amount

of current (amp) draw or reduces performance. A heavier cord with a larger wire size will reduce the voltage drop.

Be sure to choose a cord that will supply enough voltage to operate your tool and/or power station. The table

below indicates appropriate gauge for extension cords.

WARNING:

Do not incinerate.

Volts

Than

Ampere Rating

Not More

Than

AWG

120V

240V

25 (7.6)

50 (15.2) 100 (30.5)

100 (30.5)

200 (61.0)

100 (30.5)

200 (61.0)

Total Length of Cord in Feet (meters)

Minimum Gauge for Extension Cord Sets

Summary of content (4 pages)

PAGE 1
Central eléctrica de 15 AMP con GFCI y luz de trabajo desmontable Station électrique 15 A avec DDFT et lampe de travail amovible DXSTA151PS 15 Amp Power Station with GFCI and Detachable Work Light INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES 1-844-377-8451 • www.dewalt.com If you have questions or comments, contact us.
PAGE 2
5. Insert supplied screws to the bracket, depending on bracket position on the rack upright, two screws will bottom out when threaded into the bracket, which is designed to be an indicator for the other two screws to stick out at the same length for proper mounting. (Slight adjustment may be require for final secure fitment.) (Fig. 4) POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS: 1-844-377-8451. 6.
PAGE 3
LIRE TOUTES LES CONSIGNES Mode d’emploi pour supports de câble (Fig. 9-10) REMARQUE : Les supports peuvent pivoter sur quatre positions différentes, par incréments de 90°. AVANT DE COMMENCER : 1. Pour faire pivoter le support, tirez à partir d’un point le proche possible de la base du support. Faites ensuite pivoter jusqu’à la position désirée, puis relâchez. Ne tirez pas à partir du haut du support. (Fig. 9) • Veuillez lire attentivement toutes les instructions.
PAGE 4
(amperaje) o reduce el rendimiento. Un cable más pesado con un tamaño de cable más grande reducirá la caída de voltaje. Asegúrese de elegir un cable que suministre suficiente voltaje para hacer funcionar a su herramienta y/o estación de energía. La siguiente tabla indica el calibre apropiado para los cables de extensión . ADVERTENCIA: Mantenga los cables eléctricos en buenas condiciones. No use cables desgastados, Instrucciones de montaje de la estación de energía a una estantería (Fig.