Full Product Manual

ManualsBrandsDEWALT ManualsGarage Storage18 in. H x 44 in. W Black Steel Pegboard (2-Pack)

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-844-377-8451 • www.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

DXST4500PBK

2 Piece Pegboard Kit for DXST4500 Industrial Rack

Ensemble de 2 panneaux perforés pour étagère industrielle DXST4500

Kit de panel perforado de 2 piezas para estantería industrial DXST4500

DEWA LT

and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an afﬁliate thereof

and are used under license. The yellow/black color scheme is a trademark for DEWALT power tools

& accessories.

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS

TECHNICAL SPECIFICATIONS

BEFORE YOU BEGIN:

Parts List

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-844-377-8451

WARNING! Read and understand all instructions. This manual contains

important safety and operating instructions. Please read this manual carefully

before assembling this storage rack and save it for reference.

Technical Specifications

Height 18" (45.72 cm)

Width 47" (119.38 cm)

No. Description Qty.

1 Metal Pegboard

2 Pegboard Mounting Beam

3 Side Mounting Bracket (Right)

4 Side Mounting Bracket (Left)

• Read all instructions thoroughly.

• Remove all components from the box, and lay them on the floor in an orderly fashion.

• Wear eye protection.

• Be cautious of sharp edges.

• Keep this information for further reference.

NOTE: DXST4500 Industrial Racks are sold separately.

WARNING:

Serious or fatal crushing injuries can occur from rack tipping over. To prevent this, the

assembled rack must always be secured to a wall, especially in earthquake-prone environments, where

surfaces are uneven, and where children and/or pets are present.

NOTE: This same process can be used for mounting double side panels.

1. Position one right and one left bracket onto the top two mounting slots of each upright on one side

of the rack with the hanging tab arrows pointing upwards. Slide the side mounting brackets down

completely into the slots to secure them. For the bottom set of mounting brackets, offset them one

slot upwards from the bottom of the rack uprights then follow the same procedure as the top mounting

brackets. (Fig. 1)

2. Take the pegboard and position it to line up the holes on the pegboard with the hanging tabs on the

mounting brackets. Slide the pegboard onto the mounting brackets, and firmly push down on the top of

the pegboard to secure it onto the mounting brackets. (Fig. 2)

3. Insert a large locking pin into the hole on the top of each of the four (4) mounting brackets. (Fig. 3)

NOTE: Pegboards can be mounted to the back or sides of racks for multi-functional organization.

NOTE: See images below for different pegboard mounting options.

Side Pegboard Panel Assembly (Fig. 1-3)

Pegboard Assembly Orientations

GENERAL SAFETY

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave tools unattended.

• Never force a part into place.

• Wear safety apparel.

• Wear safety glasses/goggles.

• Never crawl, sit, stand, or climb on a rack.

• Keep small parts away from children. Never leave a small child unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION:

(Used without word) Indicates a safety related message.

Indicates a practice not related to personal injury which, if not avoided,

may result in property damage.

NOTICE:

*Double side panels *Single side and back panels *Double back panels

No. Description Qty.

5 Rear Mounting Bracket (Right)

6 Rear Mounting Bracket (Left)

7 Large Locking Pin 12

8 Small Locking Pin

Summary of content (4 pages)

PAGE 1
DXST4500PBK 2 Piece Pegboard Kit for DXST4500 Industrial Rack Ensemble de 2 panneaux perforés pour étagère industrielle DXST4500 Kit de panel perforado de 2 piezas para estantería industrial DXST4500 INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES 1-844-377-8451 • www.dewalt.com If you have questions or comments, contact us.
PAGE 2
FIG. 1 PEGBOARD FIG. 2 TOP RACK UPRIGHTS SIDE MOUNTING BRACKET (RIGHT) FIG. 3 LINE UP AND SLIDE PEGBOARD HOLE ONTO MOUNTING BRACKET HANGING TAB Définitions : Règles de sécurité LARGE LOCKING PIN IN MOUNTING BRACKETS THEN, PRESS PEGBOARD DOWN TO SECURE IT TO BRACKET Les définitions ci-dessous décrivent le niveau de danger pour chaque mot indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles.
PAGE 3
4. Montez les panneaux perforés sur les poutres de montage en commençant par le panneau inférieur. Alignez le panneau perforé avec les plaquettes de la poutre de montage et faites-le glisser vers le bas jusqu’à ce qu’il soit complètement fixé aux plaquettes. Répétez l’opération avec le panneau perforé supérieur. REMARQUE : Les bords des panneaux perforés doivent être bien alignés aux bords inférieur et supérieur des poutres de montage. (Fig. 10) 5.
PAGE 4
Lista de piezas: FIG. 1 N.° Descripción 1 Panel perforados metálico 2 2 Viga de montaje de panel perforado 2 3 Soporte de montaje lateral (derecha) 4 4 Soporte de montaje lateral (izquierda) 4 5 Soporte de montaje trasero (derecha) 2 6 Soporte de montaje trasero (izquierda) 2 7 Pasador de bloqueo grande 12 8 Pasador de bloqueo pequeño 8 FIG. 2 MONTANTES SUPERIORES DE LA ESTANTERÍA PANEL PERFORADO Cant.