Use and Care Manual

ManualsBrandsDEWALT ManualsGarage ShelvingYellow 2- Tier Heavy Duty Shop Workbench Industrial Steel Garage Storage Shelving Unit 50 in. W x 56 in. H x 18 in. D

•

•---Jin

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

EWALT

EWALT.

EW A LT

and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an afliate thereof

and are used under license. The yellow/black color scheme is a trademark for D

EWALT

power tools & accessories.

Deﬁnitions: Safety Guidelines

The deﬁnitions below describe the level of severity for each signal word. Please

read the manual and pay attention to these symbols.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

(Used without word) Indicates a safety related message.

Indicates a practice not related to personal injury which, if not avoided, NOTICE:

may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-855-558-2422

WARNING! Read and understand all instructions. This manual contains

important safety and operating instructions. Please read this manual carefully

before assembling this storage rack and save it for reference.

SAVE THESE INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Technical Specifications

INDUSTRIAL RACK

Total Rack Capacity

3,000 lbs. (1,360.78 kg)

*when weight is evenly distributed

Capacity per Shelf

1,500 lbs. (680 kg)

*when weight is evenly distributed

WORK STATION

Height 47" (119.4 cm)

Width 49.5" (125.73 cm)

Depth 18" (45.72 cm)

DRAWER KIT

Height 6.21" (15.77 cm)

Width 42.95" (109.09 cm)

Depth 16.86" (42.82 cm)

Drawer Capacity 120 lbs. (54.43 kg)

PEGBOARD

Height 18" (45.72 cm)

Width 47" (119.4 cm)

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-855-558-2422 • www.dewalt.com

INSTRUCTION MANUAL

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

GUIDE D’UTILISATION

DE USAR EL PRODUCTO.

MANUAL DE INSTRUCCIONES

DXST3000WB

2-Shelf Industrial Storage Rack Work Station

Poste de travail et rangement industriel à 2 étagères

Estación de trabajo de estantería para almacenamiento industrial de 2 estantes

GENERAL SAFETY

• Keep work area clean and dry.

• Use correct/recommended tools for the job.

• Never leave unattended tools plugged in or running.

• Never force a part into place.

• Wear appropriate safety apparel for the job you are doing.

• Wear safety glasses/goggles.

• Never crawl, sit, stand, or climb on the rack, pegboards, or drawer.

• Never overload the Drawer Kit.

• Do not leave drawer open.

• Keep small parts away from children. Never leave a small child unattended while assembling.

• Always use common sense – your personal safety is your responsibility.

SPECIFIC SAFETY FOR WALL MOUNT BRACKET

WARNING:

Serious injury or death can occur from the rack tipping over. To prevent this, the rack

must be secured to a wall, especially in earthquake -prone areas, or where surfaces are uneven, and where

children and/or pets are present.

Different wall materials require different types of fasteners. Use fasteners suitable for your specific type of

wall. If you are uncertain about what type of fastener to use, then please contact your local hardware store.

WARNING:

NEVER EXCEED THE FOLLOWING WEIGHT LIMITS

• Maximum load for the Drawer: Up to 120 lbs. (54.43 kg) when evenly distributed.

• Maximum load for each shelf: Up to 1,500 lbs. (680 kg) when weight is evenly distributed.

• It is recommended that the heaviest load be placed on the bottom shelf.

• Immediately remove the load should there be damage, bending or warping of the rack uprights

Parts List

No. Description Qty. No. Description Qty.

1 Vertical Beam 2 18 Locking Grid Clip 4

2 Pre-Bolted Vertical Assembly 2 19 U-Bracket Cover 4

3 Vertical Assembly Bolt 4 20 Fold Up Drawer 1

4 Crossbeam 4 21 Drawer Pull 1

Shelf Support Strap

Safety Strap With Weld Nut

Mounting Bracket with

Drawer Slides

7 Safety Strap Bolt 8

23 Drawer Carriage Bolts 4

8 Laminate Deck 1

24 Drawer Carriage Nut

9 Wire Grid 1

25 Metal Pegboard 1

10 Locking Pin 29

26 Pegboard Mounting Beam 2

11 Carriage Bolt 2

27 Side Mounting Bracket (Right) 2

12 10 mm Nut 2

28 Side Mounting Bracket (Left) 2

13 10 mm Wrench 1

29 Rear Mounting Bracket (Right) 2

14 4 mm Hex Key 1

30 Rear Mounting Bracket (Left) 2

15 4 mm Hex Bit 1

31 Small Locking Pin 8

16 Wall Mount Bracket Assembly 1

32 Pegboard Tool Holders 6

17 Stacking Plate 2

Summary of content (8 pages)

PAGE 1
Estación de trabajo de estantería para almacenamiento industrial de 2 estantes Poste de travail et rangement industriel à 2 étagères DXST3000WB 2-Shelf Industrial Storage Rack Work Station INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES 1-855-558-2422 • www.dewalt.com If you have questions or comments, contact us.
PAGE 2
Crossbeam Installation (Fig. 3-5) 25 28 27 NOTE: It is recommended for one person to hold the upright frames in place while a second person installs the crossbeams. 1. There is a set of locking tabs at both ends of every crossbeam. To begin assembly, take one crossbeam and insert the tabs into two of the holes on the lower portion of one upright frame. Engage the locking tabs into the holes using a downward motion. The locking pin hole should be at the top.
PAGE 3
FIG. 13 FIG. 14 FIG. 22 FIG. 15 FIG. 23 TOP RACK UPRIGHTS PEGBOARD SIDE MOUNTING BRACKET (RIGHT) FIG. 24 LINE UP AND SLIDE PEGBOARD HOLE ONTO MOUNTING BRACKET HANGING TAB THEN, PRESS PEGBOARD DOWN TO SECURE IT TO BRACKET LARGE LOCKING PIN IN MOUNTING BRACKETS HANGING TAB ROCK BRACKET UPWARDS .......... ................................. ..................... A WARNING: Serious injury or death can occur from the rack tipping over.
PAGE 4
A MESURES DE SÉCURITÉ GÉNÉRALES -i ----~ 25 • Gardez la zone de travail propre et sèche. • Utilisez des outils appropriés/recommandés pour le travail. • Ne laissez jamais les outils sans surveillance. • Ne forcez jamais une pièce. • Portez des vêtements de sécurité. • Portez des lunettes de sécurité. • Assurez-vous de ne jamais ramper, vous assoir, vous tenir debout ou grimper sur un support, panneaux perforés, ou tiroir. • Ne surchargez jamais le tiroir.
PAGE 5
Instructions pour la traverse (Fig. 3-5) REMARQUE : Il est recommandé pour une personne supporte les cadres verticaux tandis qu’une deuxième personne installe les traverses. 1. Il y a un ensemble de languettes de verrouillage aux deux extrémités de chaque entretoise. Pour commencer l’assemblage, prenez la traverse et insérez les languettes dans deux des trous sur la partie inférieure d’un cadre vertical. Insérez les languettes de verrouillage dans les trous à l’aide d’un mouvement vers le bas.
PAGE 6
Partie 1b : Assemblage du panneau latéral du panneau perforé (Fig. 22-24) ESTACIÓN DE TRABAJO REMARQUE : Ce même processus peut être utilisé pour le montage des panneaux latéraux doubles. Altura 47" (119.4 cm) 1. Placez un support droit et un support gauche sur les deux fentes de montage supérieures de chaque montant d’un côté de l’étagère. Assurez-vous que les flèches de la plaquette de suspension pointent vers le haut.
PAGE 7
22 20 5. Repita los pasos 1 a 4 para ensamblar los tres marcos verticales restantes. Una vez que todos estén ensamblados, ajuste los pernos por completo en las cuatro esquinas. Tenga cuidado de no ajustar demasiado los pernos. No debe haber ninguna deformación en los soportes en forma de U ni en las vigas horizontales. FIG. 1 FIG. 2 VIGA HORIZONTAL SUPERIOR 2 ft 18" (61 cm) 45.
PAGE 8
3. Para cada conjunto de travesaños, coloque una agarradera de soporte de estante perpendicular a los travesaños e inserte cada extremo en las ranuras a cada lado del travesaño. (Fig. 11) FIG. 10 FIG. 11 BARRA DE SEGURIDAD CON TUERCA PARA SOLDAR (DEBAJO) FIG. 12 FIG. 20 FIG. 19 FIG.