TITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF DXST10000 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL
SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. Read all instructions and follow them with use of this product.
TECHNICAL SPECIFICATIONS 4 DXST10000 TECHNICAL SPECIFICATIONS TOTAL CAPACITY 10,000 lb (4,535.9 kg) *WHEN WEIGHT IS EVENLY DISTRIBUTED CAPACITY PER SHELF 2,500 lb (1,133.9 kg) *WHEN WEIGHT IS EVENLY DISTRIBUTED HEIGHT 72” (182.8 cm) WIDTH 77" (195 cm) DEPTH 24" (61 cm) WEIGHT 180.
• Keep work area clean and dry. • Use correct/recommended tools for the job. • Never leave tools unattended. • Never force a part into place. • Wear safety apparel. • Wear safety glasses/goggles. • Never crawl, sit, stand, or climb on a rack. • Keep small parts away from children. Never leave a small child unattended while assembling. • Always use common sense – your personal safety is your responsibility.
DXST10000 No. Description No. Description Qty. 1 Vertical Beam 2 10 Locking Shelf Pin 16 2 Pre-Bolted Vertical Assembly 2 11 Locking Grid Clip 12 3 Vertical Assembly Bolt 4 12 Carriage Bolt 2 4 Crossbeam 8 13 10 mm Nut 2 5 Shelf Support Strap 20 14 10 mm Wrench 1 6 Safety Strap With Weld Nut 12 15 4 mm Hex Key 1 7 Safety Strap Bolt 24 16 4 mm Hex Bit 1 8 Wire Grid 3 17 Wall Mount Bracket Assembly 1 Laminate Deck 1 9 PARTS LIST Qty.
2 4 9 8 Tools Required for Rack Assembly: 4 mm Hex Key (included) OR 4 mm Hex Bit (included); Rubber Mallet (not included) PARTS LIST 1
DXST10000 EXPANDABLE UPRIGHT FRAME INSTRUCTIONS • Note: For ease of assembly, two (2) Vertical Beams feature pre-bolted horizontal and diagonal beams. STEP 1 • 2 ft 24 (61 cm) (60.9 CM) Place one (1) Vertical Beam and one (1) Pre-Bolted Vertical Beam on the floor, parallel to one another (about 24”/60.9 cm apart). The widest part of the teardrop-shaped hole pattern on each beam should be facing upward (or away from you).
CROSSBEAM INSTRUCTIONS Note: It is recommended for one person to hold the upright frames in place while a second person installs the crossbeams. STEP 1 • LOCKING PIN HOLE There is a set of locking tabs at both ends of every crossbeam. To begin assembly, take one crossbeam and insert the tabs into two of the holes on the lower portion of one upright frame. Engage the locking tabs into the holes using a downward motion. The locking pin hole should be at the top.
DXST10000 SHELF SUPPORT AND SAFETY STRAP INSTRUCTIONS • Note: There are five (5) Shelf Support Straps and three (3) Safety Straps with Weld Nuts for every set of crossbeams. STEP 1 • Starting with the lowest set of crossbeams, place one shelf support strap perpendicular to the crossbeams and insert each end into the slots on each side of the crossbeam. STEP 2 ASSEMBLY • Continue aligning the remaining four supports perpendicularly across the beams, and secure them into place.
WALL MOUNTING INSTRUCTIONS • Note: Drywall anchors and anchor screws are included with this rack; however, different wall materials require different types of fasteners. Use fasteners suitable for your specific type of wall. If you are uncertain about what type of fasteners to use, then please contact your local hardware store. STEP 1 • Take the U-shaped bracket and rock it up at an angle to attach it to the bottom inner channel of the crossbeam.
DXST10000 LAMINATE DECK INSTRUCTIONS • Please the first laminate deck onto the top ridge of any set of crossbeams. If seated properly, it will “pop” into place and lay evenly. WIRE GRID INSTRUCTIONS ASSEMBLY • Note: Each wire grid consists of two sides. On one side, the wire runs the length of the crossbeams (the long side). One the opposite side, the wire runs the width between the set of crossbeams (the short side).
LOCKING SHELF PIN INSTRUCTIONS There is a locking pin hole at both ends of every crossbeam. This is where the locking shelf pins are to be installed. If a pin does not easily slip into place, moderately tap the end of the crossbeam closest to the upright frame to fully seat the locking tabs. MAXIMIZE YOUR DEWALT STORAGE OPTIONS NOTE: Connect multiple racks together to create the ultimate storage solution. * Additional racks are sold separately.
DXST10000 ONE YEAR LIMITED WARRANTY DEWALT will replace this industrial rack due to faulty materials or workmanship for one year from the date of purchase (please be sure to keep your receipt). This warranty does not cover part failure due to normal wear or rack abuse. This warranty does not apply to accessories or damage caused where repairs have been made or attempted. For further detail of warranty coverage, call 1-844-377-8451.
NOTES 15