If you have questions or comments, contact us. AUST 1800 841 749 NZ 0800 467 813 www.dewaltpw.
FIG. 1 A. Panel assembly B. Nozzle holder C. Professional spray gun D. Tyres E. Quick-connect spray wand F. Frame G. Engine H. Handle assembly I. High pressure hose J. High pressure pump I A C B Engine Refer to the engine instruction manual for location and operation of other engine controls.
Specifications PSI* LPM* ENGINE 3300 PSI 9.4 L/min HONDA** GC190 187 cc * Rated Pressure and Rated Water Flow is within manufacturing tolerance of (+/- 10%) ** HONDA™ is a registered trademark of the HONDA MOTOR CO., LTD used under license from AMERICAN HONDA MOTOR CO. INC. Important Safety Instructions Definitions: Safety Guidelines DANGER: Carbon Monoxide. Using an engine indoors can kill you in minutes.
English SAVE THESE INSTRUCTIONS WARNING: Do not operate this unit until you read this instruction manual and the engine instruction manual for safety, operation and maintenance instructions. WARNING: When using this product basic precautions should always be followed, including the following: 1. Read all instructions before using the product. 2. To reduce the risk of injury, close supervision is necessary when a product is used near children. 3. Know how to stop the product and bleed pressures quickly.
• Always keep pressure washer a minimum of 1.2 m away from surfaces (such as houses, automobiles or live plants) that could be damaged from muffler exhaust heat. • Improperly stored fuel could lead to accidental ignition. Fuel improperly secured could get into the hands of children or other unqualified persons. • Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind of flammable solvent with this product could result in serious injury or death.
English • Your pressure washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! • Inspect the high pressure hose regularly.
English DANGER: RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT • Unsafe operation of your • Do not use chlorine pressure washer could lead bleach or any other to serious injury or death to corrosive compound. you or others. • Become familiar with the operation and controls of the pressure washer. • Keep operating area clear of all persons, pets and obstacles. • Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times.
English • If proper starting procedure is not followed, engine can kickback causing serious hand and arm injury. • The spray gun/wand is a powerful cleaning tool that could look like a toy to a child. • Reactive force of spray will cause gun/wand to kickback, and could cause the operator to slip or fall or misdirect the spray. Improper control of gun/ wand can result in injuries to self and others. • If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure.
WARNING: RISK OF BURSTING WHAT CAN HAPPEN HOW TO PREVENT IT WHAT CAN HAPPEN • Spray directed at electri cal outlets or switches, or objects connected to an electrical circuit, could result in a fatal electrical shock. • Unplug any electrically operated product before attempting to clean it. Direct spray away from electric outlets and switches. • Over inflation of tires could result in serious injury and property damage.
English • High-velocity fluid spray directed at pneumatic tire sidewalls (such as found on automobiles, trailers and the like) could damage the sidewall resulting in serious injury. • On pressure washers rated above 1600 psi (11032 kPa) use the widest fan spray (40º nozzle) and keep the spray a minimum of 200 mm from the pneumatic tire sidewall. Do not aim spray directly at the joint between the tire and rim.
FIG. 3 The pressure setting is preset at the factory to achieve op ti mum pressure and cleaning. To lower the pressure, follow these instructions. 1. Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream of water and a wider spray pattern. Refer to Spray Wand Nozzles. NOTICE: DO NOT attempt to increase pump pressure.
English Nozzle Color Spray Pattern Uses Surfaces*** 0˚ powerful pinpoint for very intense cleaning metal or concrete; DO NOT use on wood 15˚ intense cleaning of small areas metal, concrete or wood 25˚ intense cleaning of larger areas metal, concrete or wood 40˚ covers wide areas of cleaning metal, concrete, wood or vinyl Red Yellow Green White low pressure applies cleaning solutions CHANGING NOZZLES ON SPRAY WAND DANGER: Risk of fluid injection.
• Operate pressure washer in a well-ventilated area. Avoid enclosed areas such as garages, basements, etc. • Never operate unit in or near a location occupied by humans or animals. WARNING: Risk of fire, asphyxiation and burning. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • NEVER fill fuel tank completely. Fill tank to 12.7 mm below bottom of filler neck to provide space for fuel expansion.
English START-UP PROCEDURE (FIG. 1, 10–16) 1. In a well-ventilated outdoor area, add fresh, high-quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure. NOTICE: Use of fuels with greater than 10% ethanol are not approved for use in this product per EPA regulations and will damage the unit and void the warranty. 2. Check engine oil level.
NOTICE: Risk of property damage Failure to do so could cause damage to the pump. 2. Place the engine ON/OFF switch (H) to the OFF Position. FIG. 14 FIG. 16 OFF ON FIG. 15 NOTICE: Risk of property damage. NEVER turn water supply off while pressure washer engine is running or damage to pump will result. 4. Turn water source off. 5. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 6. Refer to Storage for proper storage procedures. X 15.
English temperatures or dusty conditions, more frequent maintenance checks will be required. 5. Direct water supply into spray nozzle to back flush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun then turn on water supply. 8. Start pressure washer and place spray wand into high pressure setting to test. Engine Consult the engine instruction manual for the man u fac tur er's recommendations for any and all maintenance.
STORAGE Engine ACCESSORIES Consult the engine instruction manual for the manufacturer's recommendations for storage. Pump The manufacturer recommends using a pump guard product when storing the unit for more than 30 days and/or when freezing temperatures are expected. NOTE: Using pump guard helps provide proper lubrication to the internal seals of the pump regardless of temperature or environment. NOTICE: Risk of property damage.
English Limited Warranty Warranty Periods: The manufacturer of this product agrees to repair or replace designated parts that prove defective within the warranty periods below. Specific limitations/extensions and exclusions apply. These warranties pass through to the end user and are non-transferable. This warranty covers defects in material and workmanship.
Glossary Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. Chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents. Chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness. Choke control: Opens and closes carburetor choke valve. CU: Cleaning Units. GPM multiplied by psi.
English Troubleshooting Guide This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified FNA technician or your dealer. Problem Code Engine will not start .........................................................................................................
(Troubleshooting Codes cont.) POSSIBLE CAUSE Low water supply. Leak at high pressure hose fitting. Nozzle obstructed. Water filter screen clogged. 14 Air in hose. 15 16 Choke lever in the CHOKE position. High pressure hose is too long. 17 Spray wand not in low pressure. 18 19 Chemical filter clogged. Chemical screen not in cleaning solution. 20 Chemical too thick. 21 22 23 24 25 26 27 Worn seal or packing. Chemical build up in chemical injector. Worn or obstructed valves. Worn unloader piston.
(Troubleshooting Codes cont.) English CODE 28 POSSIBLE CAUSE Pump head or tubes damaged from freezing. POSSIBLE SOLUTION Have replaced by authorized service center. 29 30 Oil seals worn. Loose drain plug. Have replaced by authorized service center Tighten. 31 32 Worn or torn drain plug o-ring. Worn or torn fill plug o-ring. Check and replace. Check and replace. 33 Pump overfilled. Check for correct amount. 34 35 Incorrect oil used. Vent plug is clogged. 36 Air filter filled with oil.
