Product Manual

Instruction Manual
Guide D’utilisation
M
anual de instrucciones
AIRLINK™
11:53
99%
Unit Nickname:
Serial Number:
Ex: “Garage”
AIR COMPRESSOR MAINTENANCE
SETTINGS
Air Compressor Monitoring System
Parts Manual #
Parts Manual Rev:
Compressor Model Number:
Power Type:
The following data will populate automatically upon selecting a
a compressor model number from the drop down menu. However,
the values can also be populated manually if you have a different
brand air compressor. Refer to that compressor’s manual for
Maintenance intervals.
Electric
Ex: “1234567890”
Ex: “200-3165”
Ex: “A”
Select
Patent Pending
AIRLINK™
11:53
99%
Pump Oil Change Interval in Months:
Ex: "6
Pump Filter Check Interval Hrs:
Ex: "50
Pump Filter Check Interval Months:
Ex: "6
Fastener Torque Interval in Hours:
Ex: "200
Fastener Torque Interval in Months:
Ex: "12
Electric Motor Horespower:
Ex: "3.7
Compressor Run Hours:
0
Average Kwh Cost $:
Ex:"$0.12
Tank Drain Notication:
Daily Maintenance Notication:
Daily Alert Time
On
On
SET DAILY TIME
Ex: “200”
Air Compressor Monitoring System
OFF
BatteryDashboard Settings Maintenance Connection
Patent Pending
Drive Type:
Direct
Pump Oil Change Interval in Hours:
Ex: “200”
Pump Oil Change Interval in Months:
Ex: “6”
Pump Oil Change Interval Hrs:
Ex: “50”
Pump Oil Change Interval Months:
Ex: “6”
Fastener Torque Interval in Hours:
Ex: “200”
Fastener Torque Interval in Months:
Ex: “12”
Electric Motor Horsepower:
Ex: “3.7”
Compressor Run Hours:
0
Average Kwh Cost $:
Ex: “$0.12”
ENGLISH
WARNING: To reduce the risk of injury, user
must download and read instruction manual
before operating product. This quick start guide
is not a substitute for reading the manual. The
manual contains detailed information and
instructions that the user must be aware of and
follow in order to maintain the product
properly and use it safely.
WARNING: Battery acid leakage can cause
personal injury and cause damage to the
product and surrounding property. If battery
leakage occurs, thoroughly wash any affected
skin, making sure to keep battery acid away
from eyes, ears, nose and mouth. Immediately
wash any clothing or other surface that comes
in contact with leaked battery acid. If a
chemical burn occurs or if irritation persists,
seek medical attention. Dispose according to
Local, State or Federal regulations.
• Batteries are to be inserted following the
polarity markings on the product.
• NEVER mix old and new batteries or different
brands of batteries. Replace all batteries at the
same time.
• NEVER mix alkaline, standard (carbon-zinc),
rechargeable (nickel-cadmium) batteries with
this product.
• NEVER dispose of batteries in fire, as they may
leak and explode.
• Promptly remove exhausted batteries from
product.
• Remove batteries before extended storage.
Contents (Fig. A)
x1 Air Compressor Monitoring Device
x3 AA batteries
x2 Velcro strips (1 hook, 1 loop)
x1 Alcohol pad
Install Batteries (Fig. B-D)
Use a #1 or smaller Phillips screwdriver (not
included) to open and install (3) AA batteries.
Put cover back on and tighten the screws.
Surface Preparations (Fig. E-F)
Use alcohol pad to clean mounting location
on the compressor platform and back of the
Air Compressor Monitoring Device.
Secure Velcro Strips (Fig. G-H)
Attach one velcro strip to back of the Air
Compressor Monitoring Device. Attach other
velcro strip to the compressor.
Surface Installation (Fig. I)
Mount Air Compressor Monitoring Device
firmly by matching and firmly pressing velcro
pieces together.
Download and Install the APP (Fig. J)
On a smart phone or tablet go to Google Play
Store™ or Apple App Store™. When searching
on the app store, ‘DEWALT Air Compressor
Monitoring System’ will be listed as text along-
side the icon . Install the App.
Open the APP on Phone (Fig. J-K)
Press Air Compressor Monitoring System App
icon . Then press
ADD COMPRESSOR
.
Input Compressor Information (Fig. L)
Press
ADD NEW
.
Then either select a pre-loaded
DEWALT model number, or enter your own
model number, and fill in all the fields.
Turn on the Air Compressor
Monitoring Device (Fig. M-N)
Once Air Compressor Monitoring Device is on
the compressor, press and hold power button
for 6 seconds. Blue/red LED light flashes when
in pairing mode.
Pair Device (Fig. O-P)
Press
PAIR DEVICE
on the App. When the
“Discovering” button appears, press it.
When the
ADD
button appears at the bottom
of the screen, press it. Setup is complete.
Troubleshooting
If no device is found:
• Make sure phone or tablet is within 30 feet
of the Air Compressor Monitoring Device
while pairing.
• Air Compressor Monitoring System Pairing
Mode may have timed out. If LED light
is no longer flashing red/blue, press and
hold power button for 6 seconds to put Air
Compressor Monitoring Device back into
Pairing Mode.
Note: Air Compressor Monitoring Device
should be flashing red/blue if in Pairing Mode
• Make sure there are batteries in the Air
Compressor Monitoring Device.
• Make sure you did not connect the Air
Compressor Monitoring System through the
“Bluetooth” setting on your phone, it must
be connected through the Air Compressor
Monitoring System application only. If your
app and Air Compressor Monitoring Device
stop interacting, check for system updates
on your IOS or Android phone.
• Check Air Compressor Monitoring System
App occasionally for updates to the App.
DXCM024-0393
11:53
99%
Pump Oil Change Interval in Months:
Ex: "6
Pump Filter Check Interval Hrs:
Ex: "50
Pump Filter Check Interval Months:
Ex: "6
Fastener Torque Interval in Hours:
Ex: "200
Fastener Torque Interval in Months:
Ex: "12
Electric Motor Horespower:
Ex: "3.7
Compressor Run Hours:
0
Average Kwh Cost $:
Ex:"$0.12
Tank Drain Notication:
Daily Maintenance Notication:
Daily Alert Time
On
On
Air Compressor Monitoring System
AIR COMPRESSOR SETTINGS
PAIR DEVICE
SET DAILY TIME
ADD
Phone Web Mail Tunes
ACMS
ACMS
11:53
99%
11:53
99%
Air Compressor Monitoring System
AIR COMPRESSOR
MONITORING SYSTEM
ADD COMPRESSOR
NEED A NEW COMPRESSOR? WE CAN HELP.
VIEW OUR SELECTION GUIDE
Patent Pending
AIRLINK™
11:53
99%
Air Compressor Monitoring System
AIR COMPRESSOR SETTINGS
Patent Pending
ADD NEW
11:53
99%
Ex: “200”
Air Compressor Monitoring System
OFF
BatteryDashboard Settings Maintenance Connection
Pump Oil Change Interval Months:
Ex: “6”
Patent Pending
Fastener Torque Interval in Hours:
Ex: “200”
Fastener Torque Interval in Months:
Ex: “12”
Electric Motor Horsepower:
Ex: “3.7”
Compressor Run Hours:
0
Average Kwh Cost $:
Tank Drain Notification:
Daily Maintenance Notification:
Ex: “$0.12”
Daily Alert Time
On
Off
PAIR DEVICE
SET DAILY TIME
11:53
99%
Pump Oil Change Interval in Months:
Ex: "6
Pump Filter Check Interval Hrs:
Ex: "50
Pump Filter Check Interval Months:
Ex: "6
Fastener Torque Interval in Hours:
Ex: "200
Fastener Torque Interval in Months:
Ex: "12
Electric Motor Horespower:
Ex: "3.7
Compressor Run Hours:
0
Average Kwh Cost $:
Ex:"$0.12
Tank Drain Notication:
Daily Maintenance Notication:
Daily Alert Time
On
O
SET DAILY TIME
PAIR DEVICE
Discovering
DEWALT 62:BB -- 36 BC:33:AC:BD:62:BB
Air Compressor Monitoring System
Fig. A Fig. B
Fig. C Fig. D
Fig. E Fig. F
Fig. G Fig. H
Fig. I Fig. J
Fig. K Fig. L
Fig. M Fig. N
Fig. O Fig. P
STRIP 2
VELCRO
Phone Web Mail Tunes
11:53
99%
200-3207-1021
For complete, detailed instructions, download
the User Manual from www.DEWALT.com
Power button.
LED light.