DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 DWFP12569 2-N-1™ FLOORING TOOL HERRAMIENTA 2 EN 1™ PARA INSTALACIÓN DE PISOS OUTIL À PLANCHER 2 EN ™ INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTIONS DE FONCTIONNEMENT, CENTRES DE SERVICE, POLITIQUE DE GARANTIE.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 INTRODUCTION DEWALT tools are precision-built tools, designed for precise, high volume nailing. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and understand the safety warnings and cautions.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 DWFP12569 TOOL SPECIFICATIONS All dimentions in inches unless otherwise specified MODEL LENGTH HEIGHT WIDTH WEIGHT DWFP12569 20.35” (517 mm) 22.08” (561 mm) 3.15” (80 mm) 10.85 lbs (4.9 kg) FASTENER SPECIFICATIONS: MODEL FASTENER CROWN WIDTH GAUGE FASTENER RANGE DWFP12569 BCS15xx 1/2” (13mm) 15-1/2 Ga., 1/2" Crown Staples 1-1/2" (38mm) to 2" (50mm) DWFP12569 FLN-xxx - 16 Ga.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 AIR SUPPLY AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a minimum of 150 p.s.i. (10.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 LOADING THE DWFP12569 EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 IN ADDITION TO THE OTHER WARNINGS CONTAINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERATION • Use the DEWALT pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area. • Do not use the tool as a hammer. • Always carry the tool by the handle.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 MAINTAINING THE DWFP12569 SERIES TOOLS TO REPLACE PISTON: a. Insert the flats on the lower end of the driver piston stem carefully into the end of piston and plunger wrench, BC1009. b. Using another special wrench, BC1009, or another wrench of the proper size, unscrew the plunger from the upper end of the stem. After this is done, it will be possible to lift the poppet off the stem. c.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 INTRODUCCIÓN Las herramientas DEWALT son herramientas construidas a precisión, diseñadas para clavar con exactitud un alto volumen de clavos. Estas herramientas entregan un servicio eficiente y fiable cuando se usan correctamente y con cuidado. Al igual que con toda herramienta automática de calidad, deben seguirse las instrucciones del fabricante para obtener el óptimo rendimiento.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 INSTRUCCIONES DE SEGURIDAD Al cargar, operar o dar servicio a esta herramienta, el operador y los demás presentes en el área de trabajo deben usar SIEMPRE PROTECCIÓN DE LOS OJOS en conformidad con las especificaciones ANSI y que proteja contra partículas que vuelen por DELANTE y por el LADO, cuando se haga la conexión al suministro de aire.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 ESPECIFICACIONES DE LA HERRAMIENTA DWFP12569 Todos las medidas de tornillos y tuercas son inglés. MODELO LARGO ALTURA ANCHO PESO DWFP12569 517 mm (20,35”) 561 mm (22,08”) 80 mm (3,15”) 4,9 kg (10.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 MANTENIMIENTO DE LA HERRAMIENTA Tome nota de las advertencias en este manual al trabajar con herramientas neumáticas y tenga mayor cuidado al evaluar herramientas problemáticas. SUMINISTRO DE AIRE Y CONEXIONES No use oxígeno, gases combustibles ni gases envasados en cilindros para operar esta herramienta porque puede explotar, causando posibles lesiones.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 CARGA DE LAS HERRAMIENTAS SERIE F Al cargar, operar o dar servicio a esta herramienta, el operador y los demás presentes en el área de trabajo deben usar SIEMPRE PROTECCIÓN DE LOS OJOS en conformidad con las especificaciones ANSI y que proteja contra partículas que vuelen por DELANTE y por el LADO, cuando se haga la conexión al suministro de aire.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 ADEMÁS DE LAS OTRAS ADVERTENCIAS CONTENIDAS EN ESTE MANUAL OBSERVE LO SIGUIENTE PARA LA OPERACIÓN SEGURA • Use la herramienta neumática DEWALT solamente para el fin que fue diseñada. • Nunca use esta herramienta en forma que pueda causar la salida de una fijación hacia el usuario u otros presentes en el área de trabajo. • No use la herramienta como martillo.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 MANTENIMIENTO DE LAS HERRAMIENTAS DE LA SERIE DWFP12569 PARA REEMPLAZAR EL PISTÓN: a. Inserte con cuidado el extremo plano de la sección inferior del vástago del pistón del impulsor en el extremo del pistón y de la llave de émbolo, BC1009. b. Con ayuda de otra llave especial BC1009 u otra de tamaño adecuado, destornille el émbolo del extremo superior del vástago.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 INTRODUCTION Le DWFP12569 de DEWALT est un outil de précision, conçu pour clouer de grandes surfaces très apidement Ces cloueurs sont faits pour assurer un service efficace et durable, à condition d’être utilisés avec un inimum d’attention et dans des conditions normales d’utilisation.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 INSTRUCTIONS DE SÉCURITÉ Une PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit TOUJOURS être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement à une source d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 CARACTÉRISTIQUES DU DWFP12569 Toutes les mesures des vis et des boulons sont dans le système anglais. MODELE LONGEUR HAUTEUR LARGEUR POIDS DWFP12569 517 mm (20,35”) 561 mm (22,08”) 80 mm (3,15”) 4,9 kg (10.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 ENTRETIEN DE L’APPAREIL Lors de l’utilisation d’un outil fonctionnant sous-pression, lire les avertissements du manuel et user d’extrêmes précautions lors de la découverte d’un problème. ALIMENTATION EN AIR ET CONNEXIONS N’utilisez jamais de l’oxygène, des gaz combustibles ou des bouteilles de gaz comme source d’alimentation pour cet outil; il pourrait exploser et causer des blessures.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 CHARGEMENT DES OUTILS DE LA SÉRIE F Une PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’AVANT et des CÔTÉS, doit TOUJOURS être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement à une source d’air, du chargement, du fonctionnement et de la maintenance de l’outil.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 EN PLUS DES AUTRES AVERTISSEMENTS CONTENUS DANS CE MANUEL, VEILLEZ À OBSERVER LES PRÉCAUTIONS SUIVANTES : • N’utilisez jamais l’outil pneumatique DEWALT dans un but autre que celui pour lequel il a été conçu. • N’orientez jamais l’outil de façon à ce qu’il puisse éjecter une attache en direction de l’utilisateur ou d’autres personnes dans la zone de travail. • N’utilisez jamais l’outil comme un marteau.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 ENTRETIEN DES OUTILS DE LA SÉRIE DWFP12569 POUR REMPLACER LE PISTON : a. Insérer les flasques sur l’extrémité inférieure de la tige de piston d’entraînement avec précautions dans l’extrémité du piston et la clé de démontage de piston, BC1009. b. En utilisant une autre clé spéciale BC1009, ou une autre clé de taille adéquate, dévisser le piston de la partie supérieure de la tige.
DWFP12569_9R202311RA_DWLT_2in1 FLOORING TOOL MANUAL_MAN_JM:103697RevE_MIIIFS_MIIIFN.qxd 2012/9/25 上 DÉPANNAGE PROBLÈME CAUSE SOLUTION Le logement de soupape de la gâchette laisse fuir de l’air Le joint torique est coupé ou craquelé Remplacez le joint torique La tige de soupape de la gâchette laisse fuir de l’air.