® DW743
11 10 1A 12 13 14 15 9 8 16 17 6 7 5 4 19 18 1 2 3 A1 20 27 28 26 21 22 24 A2 25 23
0 29 33 31 32 A3 36 37 38 42 40 39 34 35 A4 41 A5
3 44 35 A7 A6 B H 45 B1 B H A8 B2
3 52 4 48 49 50 51 D C 56 54 53 22 56 26 19 E1 E2 27 13 14 59 61 60 57 30 F1 57 62 F2
21 61 50 16 66 F3 63 9 65 G H 76 75 68 67 67 68 24 8 0° 72 69 70 71 24 K1 J 73 73 74 72 K2 L1 77 45° 71 L2 M1 75 76
27 7 79 M2 N1 19 26 N2 30 82 80 81 29 59 30 2 mm 3-8 mm O P 88 33 84 85 86 83 Q R S T 87
24 U V W X1 93 X2 92 90 93 91 X3 Y 89
ENGLISH FLIP-OVER SAW DW743 Congratulations! EC-Declaration of conformity You have chosen a DEWALT product. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional users. Table of contents Technical data EC-Declaration of conformity Safety instructions Package contents Description Electrical safety Mains plug replacement (U.K.
ENGLISH Safety instructions When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Keep work area well lit.
ENGLISH • Allow the motor to reach full speed before cutting. • Raise the blade from the kerf in the workpiece prior to releasing the switch. • Do not wedge anything against the fan to hold the motor shaft. • Never place either hand in the blade area when the saw is connected to the electrical power source. • Do not attempt to cut excessively small pieces.
ENGLISH Mains plug replacement (U.K. & Ireland only) Optional accessories For use in mitre saw mode: A3 32 Mitre fence (DE3496) A4 34 Adjustable stand 760 mm (max.
ENGLISH Assembly for mitre saw mode Mounting the under-table guard (fig. D) The under-table guard (48) is fitted to the top of the saw bench table. • Place the two hooks on the left of the guard into the oblong slots (49) on the left of the blade slot (50). • Place the guard flat on the table and press it in the locking grommet (51). • To remove, loosen the grommet with a screwdriver (52) and proceed in reverse order. Turning the sawhead and table over (fig.
ENGLISH Checking and adjusting the 45° bevel position in mitre mode (fig. M1 & M2) • Ensure that the sawhead is to its extreme left-hand position with the bevel clamp handle locked. • Release and retract the lower guard. • Check the angle from the blade to the table with a suitable protractor. It should be 45° (fig. M1). • If adjustment is required, proceed as follows: • Adjust the grub screw (78) as required. The grub screw is self-locking (fig. M2).
ENGLISH • To switch the machine on, press the green start button (87). • To switch the machine off, press the red stop button (88). Mitre saw mode (fig. A) • To switch the machine on, keep the guard retraction lever (12) squeezed and press the trigger switch (1A). • To switch the machine off, release the trigger switch. Basic saw cuts Sawing in mitre saw mode It is dangerous to operate without guarding. Guards must be in position when sawing. Always clamp the workpiece when cutting non-ferrous metals.
ENGLISH Optional accessories Prior to assembling any accessories always unplug the machine. Dust extraction kit (fig. A1, A2 & A8) This machine is provided with three dust extraction points for use in each mode. • Whenever possible, connect a dust extraction device designed in accordance with the relevant regulations regarding dust emission. Connecting - mitre saw position • Connect one hose to the under-table guard.