INSTRUCTION MANUAL DCF895-XE 6.
LPA (sound pressure) dB(A) 97 KPA (sound pressure uncertainty) dB(A) 3 LWA (sound power) dB(A) 108 KWA (sound power uncertainty) dB(A) 3 Vibration total values (triax vector sum) determined according to EN 60745: Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
GENERAL POWER TOOL SAFETY WARNINGS 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods. WARNING: We recommend the use of a residual current device with a residual current rating of 30mA or less.
Important Safety Instructions for All Battery Chargers NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in the ON position. WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g.
Indicator Light Operation • Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing. • Do not operate the charger with a damaged cord or plug. • Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way.
be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug the charger before attempting to clean. 7. Do not freeze or immerse the charger in water or any other liquid. WARNING: Shock hazard. Don’t allow any liquid to get inside the charger. Electric shock may result. WARNING: Burn hazard. Do not submerge the battery pack in any liquid or allow any liquid to enter the battery pack.
F. Battery pack Belt Hook and Bit Clip (Fig. 2, 3) L. Magnetic bit clip FIG. 2 WARNING: To reduce the risk of serious personal L injury, place the forward/reverse button in the lockoff position or turn tool off and disconnect battery I pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury. WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook.
Forward/Reverse Control Button (Fig. 2) FIG. 4 A forward/reverse control button (B) determines the direction of the tool and also serves as a lock-off button. To select forward rotation, release the trigger switch (A) and depress the forward/reverse control button on the right side of the tool. To select reverse, release the trigger switch and depress the forward/reverse control button on the left side of the tool. The center position of the control button locks the trigger switch in the off position.
MAINTENANCE FIG. 7 FIG. 6 WARNING: To reduce the risk of serious personal injury, place the forward/ reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. D Lubrication D Your power tool requires no additional lubrication. C Cleaning Usage WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ) 0800 339 258. WARNING: To reduce the risk of injury, use only DEWALT impact-ready accessories. CAUTION: Use only impact sockets. Non-impact sockets may break and cause a hazardous condition.
DEWALT BATTERY AND CHARGER SYSTEMS Battery Output Nominal Chargers/Charge Time 240 Volts 12 Volts Cat.
