INSTRUCTION MANUAL DCF813-XE 3/8" (9.5 mm) 10.8 V CORDLESS IMPACT WRENCH DCF815-XE 1/4" (6.35 mm) 10.
SAVE THESE INSTRUCTIONS Definitions: Safety Guidelines 1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods.
• DO NOT splash or immerse in water or other liquids. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40 ˚C (105 ˚F) (such as outside sheds or metal buildings in summer). WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack.
Important Safety Instructions for All Battery Chargers • Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing. • Do not operate charger with damaged cord or plug.
Charging Procedure (Fig. 1) WEAK BATTERY PACKS: Weak batteries will continue to function but should not be expected to perform as much work. FAULTY BATTERY PACKS: This charger will not charge a faulty battery pack. The charger will indicate faulty battery pack by refusing to light or by displaying problem pack or charger. NOTE: This could also mean a problem with a charger. 1. Plug the charger into an appropriate outlet before inserting battery pack. 2.
6. Do not freeze or immerse charger in water or any other liquid. WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric shock may result. CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling. FIG. 2 G C J D Storage Recommendations DCF813-XE 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 2.
ASSEMBLY AND ADJUSTMENTS FIG. 3 WARNING: To reduce the risk of serious personal injury, place the forward/ reverse button in the lock-off position or turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. G F Belt Hook (Optional Accessory) To remove the battery pack from the tool, press the release button (G) and firmly pull the battery pack out of the tool handle.
NOTE: The worklights are for lighting the immediate work surface and are not intended to be used as a flashlight. To install a socket on the hog ring anvil, firmly push socket onto the anvil (J). The hog ring (K) compresses to allow the socket to slide on. After the socket is installed, the hog ring applies pressure to help provide socket retention. To remove a socket, grasp the socket and firmly pull it off. Quick-Release Chuck (Fig. 2, 4, 5) DCF815 NOTE: The chuck accepts 1/4" (6.35 mm) hex accessories.
MAINTENANCE Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 1800 444 224 or (NZ) 0800 339 258.
DEWALT BATTERY AND CHARGER SYSTEMS Battery Output Nominal Chargers/Charge Time 240 Volts 12 Volts Cat.