www. .
Figure 1 b d e g a D26411 c f d b d h e g a c D26414 f 1
Figure 2 Figure 3 Figure 4 A 2
EN GLI S H HEAT GUN D26411, D26414 or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
E NG L I S H EC-Declaration of Conformity MACHINERY DIRECTIVE D26411, D26414 DEWALT declares that these products described under “technical data” are in compliance with: 2006/42/EC, EN 60335-1, EN 60335-2-45. These products also comply with Directive 2004/108/EC. For more information, please contact DEWALT at the following address or refer to the back of the manual. The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.
EN GLI S H d) e) f) g) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
E NG L I S H • DO NOT poke anything down the nozzle as it could give you an electric shock. Do not look down the nozzle while the unit is working because of the high temperatures being produced. • DO NOT allow paint to adhere to the nozzle or scraper as it could ignite after some time. • DO NOT remove the heat barrel cover during use. Additional Safety Warnings for Heat Guns • To reduce the risk of explosion, DO NOT use in paint spray booths or within 3.0 m of paint spraying operations.
EN GLI S H 4. Work in one room at a time. Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths. 5. Children, pregnant or potentially pregnant women and nursing mothers should not be present in the work area until the work is done and all clean up is complete. 6. Wear a dust respirator mask or a dual filter (dust and fume) respirator mask. Be sure the mask fits.
E NG L I S H DATE CODE POSITION (FIG. 1) Your DEWALT tool is double insulated in accordance with EN 60335; therefore no earth wire is required. The Date Code (h), which also includes the year of manufacture, is printed into the housing. WARNING: 115 V units have to be operated via a fail-safe isolating transformer with an earth screen between the primary and secondary winding.
EN GLI S H D26414 Icon • Press and release the LCD air temperature indicator and adjuster (d) to set the desired temperature in 10˚ C increments. • To continously increase or decrease the temperature press and hold the LCD air temperature indicator and adjuster (d). • Release the indicator when desired temperature or minimum/maximum temperature is reached. • The display shows the actual rising/falling temperature until the desired temperature is reached.
E NG L I S H Switching On and Off (fig. 4) 1. Push the on/off switch (a) to the desired air flow settings: I: 240 liter/min (50ºC–400ºC) 250 liter/min (50˚–400˚C)] (D26414) A low air flow to heat up the workpiece slowly. II: 450 liter/min (50˚–600˚C) 500 liter/min (50˚–600˚C) (D26414) A high air flow to heat up the workpiece quickly. 2. To turn the tool off, push the on/off switch (a) to position O. Disconnect the tool from the power source and let the tool cool down before moving or storing it.
EN GLI S H Lubrication Your power tool requires no additional lubrication. Cleaning WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts.
E NG L I S H GUARANTEE DEWALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.