D25501 D25601 D25602 D25603 D25820 D25831
Figure 1A m l f d a f w i h c D25501 f D25501, D25820 D25820 f e m l d a t w i b g h e c D25602, D25603 1
Figure 1B c m l f e d a w g p D25831 e Figure 2A l j k n m i h c 2 o
Figure 2B c z j p Figure 3 D25602 D25601 s t u D-65510 DEWALT, Y GERMAN IDSTEIN, lpU.com www.2he ALT.eu www.
Figure 4A Figure 5 f Figure 4B m Figure 6 D25831 D25501, D25601, D25602, D25603, D25820 d d c 4
EN GLI S H SDS MAX ® COMBINATION & CHIPPING HAMMERS D25501, D25601, D25602, D25603, D25820, D25831 Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users. Technical Data Voltage (U.K.
E NG L I S H differ. This may significantly increase the exposure level over the total working period. An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
EN GLI S H 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions.
E NG L I S H 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Red service indicator LED. For detailed description see under Service Indicator LED's. Yellow service indicator LED. For detailed description see under Service Indicator LED's. Additional Safety Instructions for Rotary Hammers • Wear ear protectors. Exposure to noise can cause hearing loss.
EN GLI S H i. Side handle clamp j. Steel ring k. Bush l. Tool holder m. Locking sleeve n. Pin o. Collar p. Side handle knob INTENDED USE D25501, D25601, D25602, D25603 Your rotary hammer has been designed for professional rotary drilling and chipping applications. D25820, D25831 Your chipping hammer has been designed for professional chipping, chiselling and demolition applications. DO NOT use under wet conditions or in presence of flammable liquids or gases. These hammers are professional power tools.
E NG L I S H indicator starts to flash if there is a fault with the tool or the brushes have completely worn out (refer to Brushes under Maintenance). D25831 The red service indicator LED (r) lights up if there is a fault with the tool or the brushes have completely worn out (refer to Brushes under Maintenance). Fully Vibration-Dampened Main Handle (fig. 1) D25601, D25602, D25603, D25831 The dampers in the main handle (d) absorb the vibrations transmitted to the user.
EN GLI S H 4. Slide and rotate the side handle to the desired position. 1. Rotate the mode selector switch (f) until it points position. towards the 5. Lock the side handle in place by tightening the knob (p). 2. Rotate the chisel in the desired position. Inserting and Removing SDS Max Accessories (fig. 1, 4A, 4B) ® This machine uses SDS Max® bits and chisels (refer to the inset in figure 4B for a cross-section of an SDS Max® bit shank). 1. Clean the bit shank. 2.
E NG L I S H 3. Release the button to lock rod into position. When drilling with the depth rod, stop when end of rod reaches surface of material. Switching On and Off (fig. 1) D25501, D25601, D25602, D25603 To turn the tool on, depress the trigger switch (a). OPERATION To stop the tool, release the trigger switch. Instructions for Use D25601, D25602, D25603 The lock-on slider (b) allows the trigger switch (a) to be locked on in chiselling mode only.
EN GLI S H 4. D25601, D25602, D25603 only: Turn the electronic speed and impact control dial (g) to a medium or high speed setting. 5. Fit and adjust the side handle (c). 6. Place the centerdrill on the spot and switch on the tool. Drill until the core penetrates into the concrete approximately 1 cm. 7. Stop the tool and remove the centerdrill. Place the core bit back into the hole and continue drilling. 8.
E NG L I S H A depth rod is available, at additional cost, as an optional accessory. GUARANTEE Consult your dealer for further information on the appropriate accessories. DEWALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user.