If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contáctenos. 1-800-4-DEWALT • www.dewalt.com INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE Definitions: Safety Guidelines The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
English e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Additional Safety Rules for Heavy Duty Rotary Hammers • Wear ear protectors. Exposure to noise can cause hearing loss. • Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
English • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities.
..........safety alert .............symbol SPM .....strokes per minute sfpm .....surface feet per .............minute J SAVE THESE INSTRUCTIONS FOR FUTURE USE F A H FIG. 1 G Motor Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does not operate, check power supply. COMPONENTS (Fig. 1) WARNING: Never modify the power tool or any part of it.
English These heavy duty rotary hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. TO CHANGE SIDES For right-hand users: slide the side handle clamp over the chuck, handle at the left. For left-hand users: slide the side handle clamp over the chuck, handle at the right.
Inserting and Removing SDS Plus® Accessories (Fig. 1) WARNING: Burn hazard. ALWAYS wear gloves when changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands. WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur.
English FIG. 5 FIG. 6 C E D D Reversing Lever (Fig. 7) (ONLY FOR D25413 & D25416) The reversing lever (H) is used to reverse the rotary hammer for backing out fasteners or jammed bits in drill-only mode. WARNING: When reversing to clear jammed bits, be ready for strong reactive torque. To reverse the rotary hammer, turn it off and position the reversing lever (H) to the right. To position the lever for forward operation, turn the rotary hammer off and push the reversing lever (H) to the left.
(ONLY FOR D25413 & D25416) 1. Always unplug the drill when attaching or changing bits or accessories. 2. Always use sharp drill bits. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits rated for percussion drilling. 3. Be sure the material to be drilled is anchored or clamped firmly.
English 2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed. 3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with the tool still running to help clear debris from the hole. 4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates the proper drilling rate.
1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. Repairs 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. LATIN AMERICA: This warranty does not apply to products sold in Latin America.
avertissements et des directives pourrait se solder par un choc électrique, un incendie et/ou une blessure grave. Français Définitions : lignes directrices en matière de sécurité CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES DIRECTIVES POUR UN USAGE ULTÉRIEUR Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière à ces symboles.
c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à la position de marche risque de provoquer un accident. d) Retirer toute clé de réglage ou clé avant de démarrer l’outil.
Français c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil électrique avant de faire tout réglage ou changement d’accessoire ou avant de ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de l’outil électrique. d) Ranger les outils électriques hors de la portée des enfants et ne permettre à aucune personne n’étant pas familière avec un outil électrique ou son mode d’emploi d’utiliser cet outil.
• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles. Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles. • Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG, American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le calibre est petit, et plus sa capacité est grande. Un calibre 16, par exemple, a une capacité supérieure à un calibre 18.
Français AVERTISSEMENT : porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ : • Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3) ; • Protection auditive ANSI S12.6 (S3.19) ; • Protection des voies respiratoires NIOSH/OSHA/MSHA.
CONSERVER CES CONSIGNES POUR UTILISATION ULTÉRIEURE J F A H FIG. 1 G Moteur S’assurer que le bloc d’alimentation est compatible avec l’inscription de la plaque signalétique.Une diminution de tension de plus de 10 % provoquera une perte de puissance et une surchauffe. Les outils DEWALT sont testés en usine ; si cet outil ne fonctionne pas, vérifier l’alimentation électrique. DESCRIPTION (Fig.
La gâchette à vitesse variable (A) permet de contrôler la vitesse. Plus on appuie sur la gâchette, plus la vitesse du marteau rotatif est grande. REMARQUE : utiliser une vitesse réduite pour commencer un trou sans pointeau, pour percer le métal, les plastiques ou la céramique, ou enfoncer des vis. Les vitesses élevées sont recommandées pour percer le bois et les panneaux d’aggloméré, et pour utiliser des accessoires abrasifs ou de polissage. Français Poignée latérale (Fig.
REMARQUE : la flèche jaune sur le cadran de sélection de mode DOIT constamment être alignée sur l’un des symboles. Il n’existe aucune position d’utilisation entre les symboles. faites tourner la mèche jusqu’à ce qu’elle se verrouille en place. La mèche sera maintenue fermement. Pour libérer un foret, tirez le mandrin (F) vers l’arrière puis retirez le foret. E-Clutch et Voyant (Fig. 4) UTILISATION (D25416 SEULEMENT) l’E-clutch offre à l’utilisateur un surcroît FIG.
Pour inverser le marteau rotatif, arrêtez-le et positionnez le levier d’inversion (H) sur la droite. Pour mettre le levier en marche avant, arrêtez le marteau rotatif puis poussez le levier d’inversion (H) sur la gauche. Tige de profondeur (Fig. 6) Français (D25413 ET D25416 SEULEMENT) POUR RÉGLER LA TIGE DE PROFONDEUR 1. Maintenez appuyé le bouton de dégagement de la tige de profondeur (E) sur la poignée latérale. 2.
production uniforme de copeaux métalliques à débit moyen indique un perçage convenable. Utiliser de l’huile de coupe pour percer dans les métaux, sauf la fonte et le laiton qui se percent à sec. REMARQUE: Il peut être plus facile de percer de gros trous dans l’acier [7,6 mm à 13 mm (5/16" à 1/2")] lorsqu’on perce un trou de guidage [3,8 mm to 5 mm (5/32" to 3/16")] au préalable.
3. Pendant la perforation de trous profonds, si la vitesse du marteau venait à diminuer, retirez la mèche partiellement du trou alors que l’outil est toujours en marche pour aider l’expulsion des débris. 4. Pour la maçonnerie, utilisez des mèches au carbure ou à maçonnerie. Un jet fluide et régulier de débris indiquera une vitesse adéquate. Nettoyage AVERTISSEMENT : enlever les saletés et la poussière hors des évents au moyen d’air comprimé propre et sec, au moins une fois par semaine.
CAPACITÉS MAXIMALES RECOMMANDÉES Capacité maximale Béton 28,5 mm (1-1/8 po) R/min 0-820 (à vide) FORET, perçage du métal 13 mm (1/2 po) Bois, alésage plat 28,5 mm (1-1/8 po) Capacité optimale Béton 13 à 25 mm (1/2 à 1 po) BPM à vide 0-4 700 Garantie limitée de trois ans Réparations Pour assurer la SÉCURITÉ et la FIABILITÉ du produit, les réparations, l’entretien et les réglages doivent être réalisés (cela comprend l’inspection et le remplacement du balai) par un centre de réparation en usine DEWALT, un ce
Français REMPLACEMENT GRATUIT DES ÉTIQUETTES D’AVERTISSEMENT : si les étiquettes d’avertissement deviennent illisibles ou sont manquantes, composer le 1 800 433-9258 (1 800 4-DEWALT) pour en obtenir le remplacement gratuit.
CONSERVE TODAS LAS ADVERTENCIAS E INSTRUCCIONES PARA FUTURAS CONSULTAS Definiciones: Normas de seguridad Las siguientes definiciones describen el nivel de gravedad de cada palabra de señal. Lea el manual y preste atención a estos símbolos. PELIGRO: indica una situación de peligro inminente que, si no se evita, provocará la muerte o lesiones graves. ADVERTENCIA: indica una situación de peligro potencial que, si no se evita, podría provocar la muerte o lesiones graves.
Español c) No exponga las herramientas eléctricas a la lluvia o a condiciones de humedad. Si entra agua a una herramienta eléctrica, aumentará el riesgo de descarga eléctrica. d) No maltrate el cable. Nunca utilice el cable para transportar, tirar o desenchufar la herramienta eléctrica. Mantenga el cable alejado del calor, el aceite, los bordes filosos y las piezas móviles. Los cables dañados o enredados aumentan el riesgo de descarga eléctrica.
b) No utilice la herramienta eléctrica si no puede encenderla o apagarla con el interruptor. Toda herramienta eléctrica que no pueda ser controlada mediante el interruptor es peligrosa y debe repararse. c) Desconecte el enchufe de la fuente de energía o el paquete de baterías de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o almacenar la herramienta eléctrica. Estas medidas de seguridad preventivas reducen el riesgo de encender la herramienta eléctrica en forma accidental.
Español • Use gafas protectoras u otra protección para los ojos. Las operaciones de martilleo pueden hacer que salgan volando astillas. Las partículas volantes pueden ocasionar daño permanente a los ojos. Use una mascarilla antipolvo o un respirador para las aplicaciones que produzcan polvo. Puede que sea necesario utilizar una protección auditiva para la mayoría de las aplicaciones. • Agarre firmemente la herramienta en todo momento. No intente utilizar esta herramienta sin sujetarla con ambas manos.
ADVERTENCIA: Use SIEMPRE lentes de seguridad. Los anteojos de diario NO SON lentes de seguridad. Utilice además una cubrebocas o mascarilla antipolvo si la operación de corte genera demasiado polvo. SIEMPRE LLEVE EQUIPO DE SEGURIDAD CERTIFICADO: • Protección ocular ANSI Z87.1 (CAN/CSA Z94.3), • Protección auditiva ANSI S12.6 (S3.19), • Protección respiratoria NIOSH/OSHA/MSHA.
Español • La etiqueta de su herramienta puede incluir los siguientes símbolos. A continuación se indican los símbolos y sus definiciones: V ............. voltios A ............ amperios Hz ........... hertz W ........... vatios min ......... minutos .......... corriente alterna ...... corriente directa .......... corriente alterna ........... Construcción de Clase I ............... o directa no ........... velocidad sin ............... (tierra) ........... Construcción de Clase II ............... carga ...
Mango lateral (Fig. 2) J F A H FIG. 1 ADVERTENCIA: Para reducir el FIG. 2 riesgo de lesiones corporales, SIEMPRE opere la herramienta con el mango lateral debidamente instalado y ajustado. El incumplimiento con lo anterior podría resultar en que el mango lateral se suelte durante la operación de la herramienta y que el operador pierda el control como consecuencia. Sostenga la herramienta con ambas manos para maximizar control. El mango lateral viene ensamblado a este rotomartillo.
El interruptor de gatillo de velocidad variable (A) permite controlar la velocidad. Cuanto más se apriete el interruptor, mayor será la velocidad del martillo rotativo. NOTA: Use velocidades menores para perforar el comienzo de orificios sin hacer una marca de centrado con un punzón, para perforar metales, plásticos o cerámica o para atornillar. Las velocidades mayores son mejores para taladrar madera y tableros compuestos y para usar accesorios abrasivos y de pulido.
FIG. 5 la herramienta. Esto podría dañar el broquero y causar lesiones corporales. Para insertar la broca, inserte el vástago aproximadamente 19 mm (3/4"), no más de 22 mm (7/8") en el broquero. Empuje y gire la broca hasta que encaje en la posición correcta. La broca quedará firmemente ajustada. Para soltar la broca, tire del portabrocas (F) hacia atrás y retire la broca. C D OPERACIÓN Barra de profundidad (Fig. 6) Posición adecuada de las manos (Fig.
FIG. 6 Taladrado (SOLO PARA D25413 Y D25416) 1. Siempre desconecte el taladro cuando instale o cambie brocas o accesorios. 2. Utilice exclusivamente brocas afiladas. PARA MADERA utilice la posición de velocidad baja y brocas helicoidales, brocas de horquilla, brocas de poder o brocas sierra. PARA METAL utilice la posición de velocidad baja y brocas helicoidales de alta velocidad o brocas sierra. PARA MAMPOSTERIA utilice brocas con punta de carburo de tungsteno.
7. Para reducir el peligro de que se atasque el taladro, reduzca la presión y deje ir suavemente la broca hacia el final del barreno. 8. Conserve el motor trabajando al retirar la broca del interior del barreno, de esta manera evitará que se atasque. 9. Con los taladros con velocidad con velocidad variable no hay necesidad de hacer una marca de centro.
Los accesorios que se recomiendan para utilizar con la herramienta están disponibles a un costo adicional en su distribuidor local o en un centro de mantenimiento autorizado. Si necesita ayuda para localizar algún accesorio, póngase en contacto con DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, llame al 1-800-4-DEWALT (1-800-433-9258) o visite nuestro sitio Web: www.dewalt.com. CAPACIDADES MÁXIMAS RECOMENDADAS Capacidad máxima Concreto de (28,5 mm) R.P.M.
CULIACAN, SIN Blvd.Emiliano Zapata 5400-1 Poniente Col. San Rafael (667) 717 89 99 GUADALAJARA, JAL Av. La Paz #1779 - Col. Americana Sector Juárez (33) 3825 6978 MEXICO, D.F. Eje Central Lázaro Cárdenas No. 18 Local D, Col. Obrera (55) 5588 9377 MERIDA, YUC Calle 63 #459-A - Col. Centro (999) 928 5038 MONTERREY, N.L. Av. Francisco I. Madero 831 Poniente - Col. Centro(818) 375 23 13 PUEBLA, PUE 17 Norte #205 - Col. Centro (222) 246 3714 QUERETARO, QRO Av. San Roque 274 - Col.
1 AÑO DE SERVICIO GRATUITO DEWALT mantendrá la herramienta y reemplazará las piezas gastadas por su uso normal, sin cobro, en cualquier momento durante un año a contar de la fecha de compra. Los artículos gastados por la clavadora, tales como la unidad de hoja y retorno del impulsador, no están cubiertas. Registro en línea Gracias por su compra.
ESPECIFIÇIONES D25413, D25416 Tension de alimentación: 120 v c.a.~ Potencia nominal: 1000 W Frecuencia de operación: 50/60 Hz Revoluciones por minuto 0-820 Consumo de corriente: 9A ESPECIFIÇIONES Tension de alimentación: Potencia nominal: Frecuencia de operación: Consumo de corriente: SOLAMENTE PARA PROPÓSITO DE MÉXICO: IMPORTADO POR: DEWALT INDUSTRIAL TOOL CO. S.A. DE C.V. AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9 COLONIA LA FE, SANTA FÉ CÓDIGO POSTAL : 01210 DELEGACIÓN ALVARO OBREGÓN MÉXICO D.F.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (APR14) Part No. N395977 D25413, D25416, D25430 Copyright © 2014 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.