www. .
Copyright DEWALT 2
Figure 1 b a d c g e h f 1
Figure 2 Figure 3 d c e Figure 4 Figure 5 b f 2
Figure 6 3
EN GLI S H CHIPPING HAMMER D25330 An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Congratulations! You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.
ENGLISH EC-Declaration of Conformity MACHINERY DIRECTIVE OUTDOOR NOISE DIRECTIVE D25330 DEWALT declares that these products described under “technical data” are in compliance with: 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009), EN 60745-1, EN 60745-2-6. 2000/14/EC, Electrical concrete breaker (hand-held), m ≤ 15 kg, Annex VIII, TÜV Rheinland Product Safety GmbH (0197), D-51105 Köln, Germany, Notified Body ID No.
EN GLI S H c) d) e) f) g) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach.
ENGLISH • Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for applications that generate dust. • Hammer bits and tools get hot during operation. Wear gloves when touching them. – Health hazards caused by breathing dust developed when working in concrete and/or masonry. Markings on Tool The following pictograms are shown on the tool: Read instruction manual before use.
EN GLI S H INTENDED USE Your chipping hammer has been designed for light chipping, chiselling and demolition applications. DO NOT use under wet conditions or in presence of flammable liquids or gases. These chipping hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. Electrical Safety The electric motor has been designed for one voltage only.
ENGLISH Replacing the Dust Cover (fig. 2) Chipping and Chiselling (fig. 1) The dust cover (e) prevents dust from entering into the mechanism. Insert the appropriate chisel and rotate it into one of 12 positions. IMPORTANT: Replace a worn dust cover immediately. Turn the tool on the tool and start working. 1. Pull back the tool holder/locking sleeve (d) and pull the dust cover (e) off. 2. Fit the new dust cover. 3. Release the tool holder/locking sleeve.
EN GLI S H Optional Accessories WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. Various types of SDS Plus® chisels are available as an option. Consult your dealer for further information on the appropriate accessories. Protecting the Environment Separate collection.
11
12
13
Belgique et Luxembourg België en Luxemburg Black & Decker - DEWALT Nieuwlandlaan 7, IZ Aarschot B156 B-3200 Aarschot Tel: +32 (0)015 - 15 47 9211 Fax: +32 (0)015 - 15 47 9210 www.dewalt.be Danmark DEWALT Sluseholmen 2-4 2450 København SV Tlf: 70201511 Fax: 70224910 www.dewalt.dk Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: 06126-21-1 Fax: 06126-21-2770 www.dewalt.de Ελλάς Black & Decker (Hellas) S.A.