® DW711
Dansk 1 Deutsch 8 English 15 Español 22 Français 29 Italiano 36 Nederlands 43 Norsk 50 Português 57 Suomi 64 Svenska 71 Türkçe 78 EÏÏËÓÈη 85 Copyright DEWALT
2 1 13 3 4 12 5 6 7 8 10 11 9 A1 14 19 A2 15 16 17 18
20 21 22 23 24 21 22 20 26 27 A3 25 25 A4 31 28 21 32 30 33 29 B A5 35 C1 34 C2 36 C3 C4
38 18 D1 55 D2 37 40 39 44 18 D3 E1 42 40 E3 E2 4 43 E4 E5 41
46 44 12 45 F1 ,, , ,, ,,, ,,, ,, ,,, , ,,, F2 12 50 47 51 49 48 49 F3 G1 8 45 7 H1 G2 44 45 11 H2 52 10 H3
31 2 mm 53 5 mm 54 H4 J1 56 J2 2 7 K 11 8 L 15 57 M N
ENGLISH TABLE TOP MITRE SAW DW711 Congratulations! EC-Declaration of conformity You have chosen a DEWALT Power Tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional Power Tool users. Table of contents Technical data EC-Declaration of conformity Safety instructions Package contents Description Electrical safety Mains plug replacement (U.K.
ENGLISH Safety instructions When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents. 2 Consider work area environment Do not expose Power Tools to humidity. Keep work area well lit.
ENGLISH 1 1 1 1 1 1 Allen key 4 mm Allen key 6 mm Two-pin spanner Dust extraction adapter for top guard Instruction manual Exploded drawing • Check for damage to the tool, parts or accessories which may have occurred during transport. • Take the time to thoroughly read and understand this manual prior to operation. • Remove the saw from the packaging material carefully. • Release the head lock down knob to raise the head of the machine. Description (fig.
ENGLISH Mounting and adjusting the rip fence (fig. C1 - C4) The rip fence consists of a fixed and a sliding fence. • Loosen the fence support locking knob (34) which holds the clamping plate in position (fig. C1). • Slide the fence onto the front of the table using the U-shaped slot as the guide (fig. C2 & C3). • Slide the fence towards the blade and tighten the locking knob. Check that the fence is parallel to the blade. If not, then adjust as follows (fig. C4).
ENGLISH If the saw blade is not exactly at 90° to the fence: • Loosen the two screws (53) and move the scale/head assembly left or right until the blade is at 90° to the fence as measured with the square (fig. H4). • Lock the mitre clamping knob (9) (fig. A1). • Tighten the two screws (53) (fig. H4). Make sure the rear edge of the mitre scale keeps in contact with the two location lugs (54) at all times. Adjusting the riving knife (fig.
ENGLISH Bevel cross-cut (fig. A1, G1 & M) Bevel angles can be set from 0° to 48° to the left. Bevels up to 45° can be cut with the head set between zero and a maximum of 45° mitre position right or left (fig. M). • Loosen the bevel clamp handle (12) and set the bevel as desired (fig. A1). • Use the 45°/48° adjustment handle (50) if required (fig. G1). • Tighten the bevel clamp handle firmly. • Proceed as for a vertical straight cross-cut. Sawing in the bench mode Ripping (fig.
ENGLISH GUARANTEE • 30 DAY NO RISK SATISFACTION GUARANTEE • If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to the point of purchase, for a full refund or exchange. Proof of purchase must be produced. • ONE YEAR FREE SERVICE CONTRACT • If you need maintenance or service for your DEWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DEWALT repair agent.
Belgique et Luxembourg België en Luxemburg DEWALT Weihoek 1, Nossegem 1930 Zaventem-Zuid Danmark DEWALT Hejrevang 26 B 3450 Allerød Tlf: Fax: 70 20 15 10 48 14 13 99 Deutschland DEWALT Richard-Klinger-Straße 65510 Idstein Tel: Fax: 06 12 62 16 061 26 21 24 40 EÏÏ¿˜ DEWALT §ÂˆÊ ™˘ÁÁÚÔ‡ 154 176 71 K·ÏÏÈı¤·, ∞ı‹Ó· España DEWALT Ctra de Acceso a Roda de Barà, km 0,7, 43883 Roda de Barà, Tarragona Tel: Fax: Fax: 977 29 71 00 977 29 71 38 977 29 71 19 France DEWALT Le Paisy BP 21, 69571 Dardilly