Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
IMPORTANT SAFETY INSTRUCTIONS Definitions: Safety Guidelines IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS CONTACT US AT: www.dewaltpw.com or 1 (877) 362 4271 WARNING: Please read this entire manual before attempting to assemble, operate or install the product. WARNING: This unit was designed for specific applications. It should not be modified and/or used for any application other than that which it was designed.
English 28. To allow free air circulation, the pressure washer should NOT be covered during operation. 29. Never touch, grasp or attempt to cover a pinhole or similar water leak on the high-pressure hose. The stream of water IS under high pressure and WILL penetrate skin. 30. Use only hoses and accessories rated for pressure higher than your pressure washer's psi. Never use with any other manufacturer’s accessories or components. 31. Never defeat the safety features of this product. 32.
Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
Downloaded from www.Manualslib.
English 9. Place the motor ON/OFF switch (K) to the ON Position. K K K DXPW2000E DXPW2500E K DXPW2000E DXPW2500E DXPW3000E DXPW3000E 10. Depress trigger on gun to start water flow. WARNING: Risk of unsafe operation. Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to kickback when triggered. 11. Release trigger to stop water flow. DANGER: Risk of injury from spray. Engage the X trigger lock (X) when gun is not in use to prevent accidental spraying. 12.
Downloaded from www.Manualslib.
English ACCESSORIES NOTE: Using pump guard helps provide proper lubrication to the internal seals of the pump regardless of temperature or environment. NOTICE: Risk of property damage. Use only SIMPSON® / POWERWASHERTM Pump Guard or equivalent. Other products could be corrosive and/or contain alcohol which may cause pump damage. 1. Turn off pressure washer and disconnect hoses from pump. 2. Unscrew bottle valve from Pump Guard bottle and remove seal. 3. Screw bottle valve back onto bottle. 4.
WARRANTY DOES NOT APPLY TO FAILURES DUE TO: • Freight damage • Damage due to chemical deterioration, scale build up, rust, corrosion or thermal expansion • Freeze damage • Damage caused by parts or accessories not obtained from an authorized dealer or not approved by the manufacturer. • Normal wear of moving parts or components affected by moving parts. MOTOR Covered by motor manufacturer warranty. See motor manual.
English Glossary PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. kPa (kilopascal): Metric pressure measurement. 1 kilopascal equal 1000 pascals. Quick-connect spray wand: Allows the user to quickly change out high-pressure nozzles. Refer to Spray Wand Nozzles.
Troubleshooting Codes CODE 1 POSSIBLE SOLUTION Place ON/OFF switch in ON position. Check that the main power supply is adequate. 3 The main voltage is insufficient, lower than the minimum required. Extension cord is too long or wire gauge is too small. 4 5 6 7 8 9 10 Tripped thermal overload due to overheating. Spray wand not in high pressure. Low water supply. Leak at high-pressure hose fitting. Nozzle obstructed. Water filter screen clogged. Air in hose.
English CODE 15 POSSIBLE CAUSE Chemical screen not in cleaning solution. 16 Chemical too thick. 17 18 19 20 21 22 23 24 Worn seal or packing. Chemical build up in chemical injector. Worn or obstructed valves. Worn unloader piston. Worn or broken o-ring. Loose hose connection. Piston packings worn. Pump head or tubes damaged from freezing. POSSIBLE SOLUTION Make sure end of chemical hose is fully submerged into cleaning solution. Dilute chemical. Chemical should be the same consistency as water.