If you have questions or comments, contact us.
&OHMJTI DXPW PRESSURE WASHER A. Panel assembly B. Nozzle holder C. Professional Spray gun D. Wheel E. Quick-connect spray wand F. Frame G. Engine dipstick/oil plug H. Engine switch I. Starter grip C FIG. 1 P J. Engine K. Throttle control lever L. Choke control M. Fuel valve lever N. Gas cap O. Handle assembly P. High-pressure hose Q. High-pressure pump R. Top handle J A B R N O Q F &OHJOF Refer to the engine instruction manual for location and operation of other engine controls.
4QFDJmDBUJPOT WEIGHT HEIGHT WIDTH LENGTH PSI** GPM** ENGINE DXPW 125 lbs (56.7 kg) 28" (71.1 cm) 24" (60.7 cm) 38" (96.5 cm) 3800 (26,200 kPa) 3.5 (13.2 L/min) HONDA GX270*** 270 cc OHV ** PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA) standard PW101. *** HONDA™ is a registered trademarks of the HONDA MOTOR CO., LTD used under license from AMERICAN HONDA MOTOR CO. INC.
&OHMJTI Service land and may also be legally required under other statutes and ordinances. WARNING: This product and its exhaust contain chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. In addition, some cleaning products and dust contain chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
t .BUFSJBMT QMBDFE BHBJOTU PS near the pressure washer can interfere with its proper ventilation features causing overheating and possible ignition of the materials. t .VGGMFS FYIBVTU IFBU DBO damage painted surfaces, melt any material sensitive to heat (such as siding, plastic, rubber, vinyl or the pressure hose, itself), and damage live plants. t *NQSPQFrly stored fuel could lead to accidental ignition. Fuel improperly secured could get into the hands of DIJMESFO PS PUIFS VORVBMJGJFE persons.
&OHMJTI DANGER: RISK OF FLUID INJECTION AND LACERATION WHAT CAN HAPPEN HOW TO PREVENT IT t :PVS QSFTTVSF XBTIFS t *OTQFDU UIF IJHI QSFTTVSF operates at fluid pressures hose regularly. Replace and velocities high enough the hose immediately if it is to penetrate human and damaged, worn, has melted animal flesh, which could from contacting the engine, result in amputation or or shows any signs of other serious injury. Leaks cracks, bubbles, pinholes, or caused by loose fittings or other leakage.
&OHMJTI DANGER: RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT IT t 6OTBGF PQFSBUJPO PG ZPVS t %P OPU VTF DIMPSJOF pressure washer could lead bleach or any other to serious injury or death to corrosive compound. you or others. t #FDPNF GBNJMJBS XJUI UIF operation and controls of the pressure washer. t ,FFQ PQFSBUJOH BSFB DMFBS of all persons, pets and obstacles. t %P OPU PQFSBUF UIF QSPEVDU when fatigued or under the influence of alcohol or drugs. Stay alert at all times.
&OHMJTI t *G QSPQFS TUBSUJOH QSPDFEVSF is not followed, engine can kickback causing serious hand and arm injury. t 5IF TQSBZ HVO XBOE JT a powerful cleaning tool that could look like a toy to a child. t 3FBDUJWF GPSDF PG TQSBZ will cause gun/wand to kickback, and could cause the operator to slip or fall or misdirect the spray. Improper control of gun/ wand can result in injuries to self and others. t *G FOHJOF EPFT OPU TUBSU BGUFS UXP QVMMT TRVFF[F USJHHFS of gun to relieve pump pressure.
WARNING: RISK OF BURSTING WHAT CAN HAPPEN HOW TO PREVENT IT t Over inflation of tires could result in serious injury and property damage. t 6TF B UJSF QSFTTVSF HBVHF to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. NOTE: Air tanks, compressors and similar FRVJQNFOU VTFE UP JOGMBUF tires can fill small tires similar to these very rapidly. Adjust pressure regulator on air supply to no more than the rating of the tire pressure.
&OHMJTI WARNING: RISK OF CHEMICAL BURN WHAT CAN HAPPEN HOW TO PREVENT IT t 6TF PG BDJET UPYJD PS t %P OPU TQSBZ BDJET HBTPMJOF corrosive chemicals, kerosene, or any other poisons, insecticides, or any flammable materials with this kind of flammable solvent product. Use only household with this product could result detergents, cleaners and in serious injury or death. degreasers recommended for use with pressure washers. t 8FBS QSPUFDUJWF DMPUIJOH to protect eyes and skin from contact with sprayed materials.
R O OPERATION 1SFTTVSF "EKVTUNFOUT 4. Attach high-pressure hose (P) to spray gun. Make sure it is secure. 5. Connect wand (E) to spray gun. Make sure connection is secure. The pressure setting is preset at the factory to achieve optimum pressure and cleaning. To lower the pressure, follow these instructions. 1. Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40˚ nozzle (white).
&OHMJTI Nozzle Color Spray Pattern Uses Surfaces* 0˚ powerful pinpoint for very intense cleaning metal or concrete; DO NOT use on wood 15˚ intense cleaning of small areas metal, concrete or wood 25˚ intense cleaning of larger areas metal, concrete or wood 40˚ covers wide areas of cleaning metal, concrete, wood or vinyl Red Yellow Green White low pressure applies cleaning solutions CHANGING NOZZLES ON SPRAY WAND DANGER: Risk of fluid injection.
4UBSUJOH WARNING: To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before starting pressure washer. DANGER: Risk of fluid injection and laceration. When using the high-pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury will occur.
&OHMJTI START-UP PROCEDURE *O B XFMM WFOUJMBUFE PVUEPPS BSFB BEE GSFTI IJHI RVBMJUZ VOMFBEFE gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine instruction manual for correct procedure. 2. Check engine oil level. Refer to the engine instruction manual for correct procedure. 3. Connect the water hose to the water source. Turn the water source on to remove all air from the hose.
&OHJOF "EKVTU TQSBZ GPS UIF UBTL CFJOH QFSGPSNFE CZ DIBOHJOH RVJDL connect nozzle. Refer to Spray Wand Nozzles. 4IVUUJOH %PXO 1. If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTICE: Risk of property damage Failure to do so could cause damage to the pump. 2. Place the engine ON/OFF switch (H) to the OFF Position. 3. Place the fuel valve lever (M) in the OFF position.
STORAGE &OHJOF &OHMJTI /P[[MF $MFBOJOH If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions: 1. Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. Y 4.
1SFTTVSF 8BTIFS WARNING: The use of any other accessory not recommended for use with this tool could be hazardous. Use only accessories rated equal to or higher than the rating of the pressure washer.
&OHMJTI -JNJUFE 8BSSBOUZ This warranty does not cover the following: machines used for rental purposes, damage resulting from shipping (claims must be filed with freighter), accident, abuse, act of God, misuse, or neglect. Neither is damage from repairs or alterations performed by nonGBDUPSZ BVUIPSJ[FE QFSTPOOFM PS GBJMVSF UP JOTUBMM BOE PQFSBUF FRVJQNFOU according to the guidelines put forth in the instruction manual.
(MPTTBSZ 19 &OHMJTI Bypass mode: Allows water to re-circulate within pump when the gun trigger is not pulled. Chemical hose: Feeds cleaning agents into the pump to mix with the water. Refer to Chemicals and Cleaning Solvents. Chemical injection system: Mixes cleaners or cleaning solvents with water to improve cleaning effectiveness. Choke control: Opens and closes carburetor choke valve. CU: Cleaning Units. GPM multiplied by psi.
&OHMJTI 5SPVCMFTIPPUJOH (VJEF 5IJT TFDUJPO QSPWJEFT B MJTU PG UIF NPSF GSFRVFOUMZ FODPVOUFSFE NBMGVODUJPOT UIFJS DBVTFT BOE DPSSFDUJWF BDUJPOT 5IF PQFSBUPS PS NBJOUFOBODF QFSTPOOFM DBO QFSGPSN TPNF DPSSFDUJWF BDUJPOT BOE PUIFST NBZ SFRVJSF UIF BTTJTUBODF PG B RVBMJGJFE '/" UFDIOJDJBO or your dealer. Problem Code Engine will not start ........................................................................................................
(5SPVCMFTIPPUJOH $PEFT cont.) POSSIBLE CAUSE Fuel valve closed. Spray wand not in high pressure. Low water supply. Leak at high-pressure hose fitting. Nozzle obstructed. Water filter screen clogged. Air in hose. 15 16 Choke lever in the CHOKE position. High-pressure hose is too long. 17 Spray wand not in low pressure. 18 19 Chemical filter clogged. Chemical screen not in cleaning solution. 20 Chemical too thick. 21 22 23 24 25 26 27 Worn seal or packing. Chemical build up in chemical injector.
(5SPVCMFTIPPUJOH $PEFT cont.) &OHMJTI CODE 28 POSSIBLE CAUSE Pump head or tubes damaged from freezing. POSSIBLE SOLUTION Have replaced by authorized service center. 29 30 Oil seals worn. Loose drain plug. Have replaced by authorized service center Tighten. 31 32 Worn drain plug o-ring Worn fill plug o-ring. Check and replace. Check and replace. 33 Pump overfilled. Check for correct amount. 34 35 Incorrect oil used. Vent plug is clogged. 36 Air filter filled with oil.
T he F N A G roup 1 8 2 5 G reenleaf Avenue, E lk G rove V illage, IL 6 0 0 0 7 C opyright © 2 0 1 1 , 2 0 1 2 DXP W 6 0 6 0 4 P a rt N o. 7 1 0 4 9 2 5 r0 (M AR 1 2 ) o l T he following are trademarks for one or more DE W ALT power tools : the yellow and blac k c o r s c heme; the “D” s haped air intake grill; the array of pyramids on the handgrip; the kit box c onfiguration; and the array of lozenge- s haped humps on the s urfac e of the tool.