Product Description

eng
Getting started
1. Open the casing of the device by removing
the screw at the bottom of the device.
2. Use the included screws to mount the back
plate of the device on the wall
4. Insert batteries into the device respecting
the polarities.
5. When the batteries are inserted, the Keypad
will start searching (up to 15 minutes) for a
Zigbee network to join. While the Keypad is
searching for a Zigbee network to join, the
yellow LED ashes.
6. If the scanning has timed out, a short press
on the menu button inside the device will
restart it.
7. After connecting the device to a network,
attach the device to the back plate by
hooking the device to the top of the back
plate and pushing the device against the
back plate.
Disposal
Dispose the product and batteries properly at
the end of their lives. This is electronic waste
which should be recycled.
1. To replace the batteries, remove the screw
at the bottom of the device and open the
casing.
2. Replace all four batteries inside the device,
respecting the polarities.
3. Reattach the device to the backplate and
reinsert the screw at the bottom of the
device
Battery replacement
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside.
CAUTION: RISK OF EXPLOSION IF BATTER-
IES ARE REPLACED BY AN INCORRECT TYPE.
DISPOSE OF THE BATTERIES IN ACCORD-
ANCE WITH INSTRUCTIONS.
a.
b.
d.
e.
f.
g
c.
8. Finally, reinsert the screw at the bottom of
the device
Resetting
Resetting is needed if you want to connect
your Keypad to another gateway or if you need
to perform a factory reset to avoid abnormal
behavior.
STEPS FOR RESETTING
1. Open the casing of the device by removing
the screw at the bottom of the device.
2. Press and hold the menu button inside the
device with a thin pin – e.g. a paper clip.
Fault nding and cleaning
• In case of a bad or wireless weak signal,
change the location of the device.
Otherwise you can relocate your gateway
or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a
short press on the button will restart it.
Placement
• You can place the Keypad both indoors and
outdoors in 0-50 degrees °C.
• Place the device, so it is easily accessible
to users.
• Avoid placing the device in direct sunlight.
• Avoid placing the device in places exposed
to direct rain.
• Avoid placing moving items 40 cm or less
from the Keypad, as they will activate the
presence sensor.
• When mounting the device outdoors, use
screws rather than tape.
Precautions
• Do not remove the product label as it
contains important information.
• Be aware that electronics are sensitive
to static electricity, so aim to discharge
before touching, and avoid touching any
components inside the device.
• Do not paint the device.
• Do not use tape for mounting the device
outdoors.
• Do not use tape for mounting if you will use
the device for security purposes, as the
tamper switch will not function.
• When mounting with tape, make sure the
surfaces are clean and dry.
Product description
The Keypad includes a tag reader and allows
you to enable and disable an alarm system.
The Keypad detects when a person is within
operating distance, which will make it light up in
the dark. The Keypad includes a tamper switch,
making it ideal for security purposes.
Version 2.1
INSTALLATION MANUAL
Keypad
3. While you are holding the button down, the
LED rst ashes once, then two times in a
row, and nally numerous times in a row.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
• When mounting with tape, the room
temperature should ideally be between 21°
C and 38° C and minimum 16° C.
• Avoid mounting with tape on rough, porous
or bered materials such as wood or
cement, as they reduce the tape bond.
CAUTION:
• Disposal of a battery into re or a hot oven,
or mechanically crushing or cutting of a
battery, that can result in an explosion;
• Leaving a battery in an extremely high
temperature surrounding environment that
can result in an explosion or the leakage of
ammable liquid or gas;
• A battery subjected to extremely low air
pressure that may result in an explosion or
the leakage of ammable liquid or gas.
3. Alternatively, you can use the double
adhesive tape to mount the backplate.
Make sure to press rmly on the backplate
with the tape to make it stick.